Related Manuals for DeWalt DCD960-XE
Summary of Contents for DeWalt DCD960-XE
-
Page 1: Instruction Manual
INSTRUCTION MANUAL DCD960-XE, DCD980-XE HEAVY-DUTY 13 mm (1/2") CORDLESS DRILL/DRIVER DCD950-XE, DCD970-XE, DCD990-XE HEAVY-DUTY 13 mm (1/2") CORDLESS HAMMERDRILL/DRILL/DRIVERS... -
Page 3: Safety Instructions For Power Tools
The term “power tool” in the warnings refers to your mains-operated (corded) power Definitions: Safety Guidelines tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these 1) WORK AREA SAFETY symbols. -
Page 4: Electrical Safety
c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits etc., in accordance with before plugging in. Carrying power tools with your finger on the switch or these instructions and in the manner intended for the particular type of plugging in power tools that have the switch on invites accidents. -
Page 5: Extension Cords
• Young children and the infirm. This appliance is not intended for use by • Wear ear protectors when hammering for extented periods of time. Prolonged young children or infirm persons without supervision. Young children should be exposure to high intensity noise can cause hearing loss. Temporary hearing loss supervised to ensure that they do not play with this appliance. -
Page 6: Residual Risks
Your risk from these exposures varies, depending on how often you do this type of Residual Risks work. To reduce your exposure to these chemicals: work in a well ventilated area, and • In spite of the application of the relevant safety regulations and the work with approved safety equipment, such as those dust masks that are specially implementation of safety devices, certain residual risks cannot be avoided. -
Page 7: Specific Safety Instructions For Lithium Ion (Li-Ion)
received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced • If battery contents come into contact with the skin, immediately wash area with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. with mild soap and water. - Page 8 • Do not disassemble charger; take it to an authorized service center when CAUTION: Burn hazard. To reduce the risk of injury, charge only D WALT service or repair is required. Incorrect reassembly may result in a risk of rechargeable batteries. Other types of batteries may burst causing personal injury and electric shock, electrocution or fire.
- Page 9 Chargers Charge Indicators Some chargers are designed to detect certain problems that can arise with battery Your tool uses a D WALT 12, 14.4, 18 Volt charger. Be sure to read all safety packs. Problems are indicated by the red light flashing at a fast rate. If this occurs, instructions before using your charger.
-
Page 10: Storage Recommendations
G. Gear shifter a. Check current at receptacle by plugging in a lamp or other appliance C. LED light H. Side handle (DCD950-XE, DCD960-XE, b. Check to see if receptacle is connected to a light switch which turns power off D. Chuck DCD970-XE only) when you turn out the lights. - Page 11 NOTE: Side handle comes equipped on models DCD950-XE, FIG. 2 DCD960-XE and DCD970-XE. Forward/Reverse Control Button (Fig. 2) A forward/reverse control button (B) determines the direction of the tool and also serves as a lock off button. To select forward rotation, release the trigger switch and depress the for ward/re verse control button on the right side of the tool.
- Page 12 Rotate the mode control collar (F) so the hammer any number. symbol is aligned with the arrow. KEYLESS SINGLE SLEEVE CHUCK (FIG. 6–8) DCD960-XE, DCD980-XE SCREWDRIVING (FIG. 4) Torque Adjustment Collar (Fig. 3–5) Your tool features a keyless chuck with one rotating...
-
Page 13: Operation
3. Insert the accessory about 19 mm (3/4") into the chuck and tighten securely by SELF-TIGHTENING CHUCK OPERATION (FIG. 9–11) rotating the chuck sleeve clockwise with one hand while holding the tool with the DCD950-XE, DCD970-XE, DCD990-XE other hand. Continue to rotate the chuck sleeve until several ratchet clicks are To insert a drill bit or other accessory: heard to ensure full gripping power. -
Page 14: Maintenance
To remove the battery pack from the tool, press the release buttons (J) and firmly Hammerdrill Operation pull the battery pack out of the tool handle. Insert it into the charger as described in 1. Select the desired speed/torque range using the gear shifter to match the speed the charger section of this manual. - Page 15 Repairs • Damage caused where repairs have been made or attempted by others. • Damage due to misuse, neglect, wear and tear, alteration or modification. This charger is not user serviceable. There are no user serviceable parts inside the This warranty gives you specific legal rights and you may have other rights under the charger.
- Page 16 WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 • 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (DEC08) Part No. N022098 DCD950-XE, DCD960-XE, DCD970-XE, DCD980-XE, DCD990-XE Copyright © 2008 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...