JBL On Air Control 2.4G Owner's Manual
Jbl speaker owner's guide 2.4g
Hide thumbs
Also See for On Air Control 2.4G:
- Service manual (14 pages) ,
- Owner's manual (9 pages) ,
- Specification sheet (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JBL On Air Control 2.4G
Summary of Contents for JBL On Air Control 2.4G
- Page 1 ® ® ON AIR CONTROL ® 2.4G OWNER’S GUIDE...
-
Page 2: Federal Communications Commission Interference Statement
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. -
Page 3: Read First
READ FIRST! Important Safety Precautions! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. -
Page 4: Unpacking The System
THANK YOU FOR CHOOSING JBL For more than 60 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident that the JBL system you have chosen will provide every note of enjoyment that you expected –... - Page 5 When in doubt, please consult your local JBL dealer or distributor. The JBL On Air Control 2.4G may be connected to your source in several ways. First, determine how you would like to use the JBL On Air Control 2.4G; then follow the setup instructions for that application.
- Page 6 If your computer does feature preamp outputs, we recommend that they be used instead of speaker outputs. If you would like to connect the computer to the JBL On Air Control 2.4G using preamp outputs on your computer, follow the steps in Connection A.
- Page 7 When first plugged in, it will sometimes take several seconds for the Control 2.4G active speaker to initialize and “wake up.” Until then, the top LED will be in red. Once the top LED is green, the bottom LED should flash green until the transmitter and active speaker “lock in.”...
-
Page 8: Operation
A/V source’s volume control. Please note that Control 2.4G will retain its volume setting when it is in standby, so there is no need to set its volume level every time the system is turned on. - Page 9 I. Once the orientation of the speaker is finalized, use the metal bar (5) in one of the holes on the molded nut (2) and tighten securely. J. Securely attach the other end (10) of the backup cord (8) to the Control 2.4G by engaging it through the bar (12) on the back speaker.
-
Page 10: Maintenance And Service
The frequency of maintenance depends on the metals involved in the connec- tions, atmospheric conditions and other factors, but once per year is the minimum. In the event that your system ever needs service, contact your local JBL dealer or distributor, or visit www.jbl.com for a service center near you. -
Page 11: Specifications
SPECIFICATIONS Frequency Range (±3dB): 50Hz – 20kHz Amplifier Output: 15 Watts per channel Low-Frequency Driver: 4" (100mm) Magnetically shielded High-Frequency Driver: 1/2" (12mm) Titanium-laminate, magnetically shielded Operating Range: Up to 70' (21m) depending upon conditions RF Operating Frequency: 2.4GHz Dimensions Speaker (H x W x D): 9"... - Page 12 JBL and Control Series are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Pro Sound Comes Home is a trademark of Harman International Industries, Incorporated. PRO SOUND COMES HOME Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA 8500 Balboa Boulevard, Northridge, CA 91329 USA 516.255.4JBL (4525) (USA only) www.jbl.com...