DeWalt DCH213-XE Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Rotary Hammer
  5. DCH213-XE
  6. Instruction manual
DeWalt DCH213-XE Instruction Manual

DeWalt DCH213-XE Instruction Manual

Heavy-duty 18v cordless rotary hammer
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
DCH213-XE
HEAVY-DUTY 18V CORDLESS ROTARY HAMMER

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCH213-XE

Summary of Contents for DeWalt DCH213-XE

  • Page 1 INSTRUCTION MANUAL DCH213-XE HEAVY-DUTY 18V CORDLESS ROTARY HAMMER...

  • Page 3: Definitions: Safety Guidelines

    1) WORK AREA SAFETY Definitions: Safety Guidelines a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the The definitions below describe the level of severity for each signal presence of flammable liquids, gases or dust.

  • Page 4: Electrical Safety

    c) Prevent unintentional starting. Ensure the switch is in the off position g) Use the power tool, accessories and tool bits etc., in accordance with before plugging in. Carrying power tools with your finger on the switch or these instructions and in the manner intended for the particular type of plugging in power tools that have the switch on invites accidents.

  • Page 5: Extension Cords

    • Replacement of the supply cord. If the supply cord is damaged, it must be be used at all times. Operating this tool with one hand will result in loss of replaced by the manufacturer or an authorised D WALT Service Centre in order control.

  • Page 6: Important Safety Instructions For All Battery Packs

    Important Safety Instructions for All Battery Packs Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and When ordering replacement battery packs, be sure to include the catalog number and work with approved safety equipment, such as those dust masks that are specially voltage.

  • Page 7: Specific Safety Instructions For Lithium Ion (Li-Ion)

    the battery terminals inadvertently come in contact with conductive materials buildup of metallic particles should be kept away from the charger cavities. Always such as keys, coins, hand tools and the like. The US Department of Transportation unplug the charger from the power supply when there is no battery pack in the cavity. Hazardous Material Regulations (HMR) actually prohibit transporting batteries in Unplug the charger before attempting to clean.

  • Page 8: Charge Indicators

    Charge Indicators • NEVER attempt to connect 2 chargers together. • The charger is designed to operate on standard 230 V household electrical This charger is designed to detect certain problems that can arise. Problems are indicated power. Do not attempt to use it on any other voltage. This does not apply to the by the red light flashing at a fast rate.

  • Page 9: Storage Recommendations

    SAVE THESE INSTRUCTIONS FOR FUTURE USE 3. A cold battery pack will charge at about half the rate of a warm battery pack. The battery pack will charge at that slower rate throughout the entire charging cycle and will not return to maximum charge rate even if the battery pack warms. COMPONENTS (FIG.

  • Page 10: Operation

    Side Handle (Fig. 2) To select forward rotation, release the trigger switch (B) and depress the forward/ reverse control button on the right side of the tool. WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with To select reverse, depress the forward/reverse control button on the left side of the the side handle (A) properly installed.
  • Page 11 Installing and Removing the Battery Pack (Fig. 4) SDS Chuck (Fig. 5) To insert bit, insert shank of bit about 19 mm (3/4") into chuck (L). Push and rotate WARNING: To reduce the risk of injury, never depress the battery release button bit until it locks in place.

  • Page 12: Maintenance

    DRILLING IN METAL 51 positions. An SDS Plus to round shank adaptor chuck is required for the DCH213-XE. Ensure ® 3. Adjust the side handle (A) as required. that tool is in drill-only mode. Start drilling with slow speed and increase to full power while applying firm pressure on the tool.
  • Page 13 Lubrication MAXIMUM RECOMMENDED CAPACITIES DCH213-XE Your power tool requires no additional lubrication. Spindle speed 0–1,110 min Cleaning Hammering speed 0–4,200 min WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once Masonry Drilling 20 mm (7/8")
  • Page 16 701 East Joppa Road, Baltimore, MD 21286 • 82 Taryn Drive, Epping, VIC 3076 Australia 1800 444 224 or (NZ) 0800 339 258 (JUL11) Part No. N129011 DCH213-XE Copyright © 2011 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

Table of Contents