Extension Cords - DeWalt DCH213-XE Instruction Manual

• Replacement of the supply cord. If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised D
to avoid a hazard.

Extension Cords

CAUTION: Use only extension cords that are approved by the country's Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
MINIMUM GAUGE FOR CORD SETS
For Cable length (m): 7.5 15
Use Cable with minimum rating (Amperes)
Tool Amperes
0 - 3.4 7.5 7.5
3.5 - 5.0 7.5 7.5
5.1 - 7.0 10 10
7.1 - 12.0 15 15
12.1 - 20.0 20 20
Additional Safety Instructions for Rotary Hammers
• Wear ear protectors. Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the tool. Loss of control can cause
personal injury.
• Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
• Be certain that the material being drilled does not conceal electric or gas
service and that their locations have been verified with the utility companies.
• Use clamps or another practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body leaves it
unstable and may lead to loss of control.
• Wear safety goggles or other eye protection. Hammering operations cause
chips to fly. Flying particles can cause permanent eye damage.
• Keep a firm grip on the tool at all times. Do not attempt to operate this tool
without holding it with both hands. It is recommended that the side handle
WALT Service Centre in order
E
25 30 45 60
7.5 7.5 7.5 7.5
7.5 7.5 10 15
10 10 15 15
15 15 20 20
20 20 25 –
NOTE: Do not overheat the bit (discoloration) while grinding a new edge. Badly worn
chisels require reforging. Do not reharden and temper the chisel.
current rating of 30mA or less.
the following standards:
other construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
3
be used at all times. Operating this tool with one hand will result in loss of
control. Breaking through or encountering hard materials such as re-bar may be
hazardous as well.
• Do not operate this tool for long periods of time. Vibration caused by hammer
action may be harmful to your hands and arms. Use gloves to provide extra
cushion and limit exposure by taking frequent rest periods.
• Do not recondition bits yourself. Chisel reconditioning should be done by an
authorized specialist. Improperly reconditioned chisels could cause injury.
• Accessories and tool may get hot during operation. Wear gloves when handling
them if performing heat producing applications such as hammerdrilling and
drilling metals.
• Never lay the tool down until the bit has come to a complete stop. Moving bits
could cause injury.
• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal
or material chips could dislodge and cause injury.
• Slightly worn chisels can be resharpened by grinding.
• Air vents often cover moving parts and should be avoided. Loose clothes,
jewelry or long hair can be caught in moving parts.
WARNING: We recommend the use of a residual current device with a residual
WARNING: ALWAYS wear approved protective safety equipment complying with
• Eye protection: AS/NZS1337 Eye Protectors for Industrial Applications;
• Hearing protection: AS/NZS1270 Acoustics – Hearing Protection;
• Respiratory protection: AS/NZS1716 Respiratory Protective Devices.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.