1. Manuals
  2. Brands
  3. Lampo Manuals
  4. Lighting Equipment
  5. IP66
  6. User manual

Lampo IP66 User Manual

Decorator 250w whell ip66 colour changer
Hide thumbs Also See for IP66:
Table of Contents

Advertisement

Quick Links

Download this manual
D
E
C
O
R
A
D
E
C
O
R
A
D
E
C
O
R
A
I
P
6
6
c
I
P
6
6
c
I
P
6
6
c
USER' S MANUAL release 1.0
This manual must be considered an integral part of the projector.
T
O
R
2
5
0
W
T
O
R
2
5
0
W
T
O
R
2
5
0
o
l
o
u
r
c
h
a
o
l
o
u
r
c
h
a
o
l
o
u
r
c
h
a
w
h
e
e
l
w
h
e
e
l
W
w
h
e
e
l
n
g
e
r
n
g
e
r
n
g
e
r

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IP66 and is the answer not in the manual?

Questions and answers

Related Manuals for Lampo IP66

Summary of Contents for Lampo IP66

  • Page 1 USER’ S MANUAL release 1.0 This manual must be considered an integral part of the projector.

  • Page 2: Table Of Contents

    BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE INSTRUCTIONS IN THIS MANUAL. AUTHORISED AND QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR. BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR.

  • Page 3: Dimensions And Weight

    Magnetic ballast with power factor correction (1.8A max @ 230VAC with lamp ON) 5 colours filter plus white, 11 colours combination with diffuser (code AP44) IP66 protection rate, not immersion! Storage The projector, in its original packing, must be kept in covered, dry areas with a temperature between –10°C and +50°C.

  • Page 4: Admissible Environmental Conditions

    Admissible environmental conditions The projector was engineered and produced to function in outdoor areas with an air temperature ranging between 0° and 35°C and with a humidity level between 30 and 90%. When choosing the installation, please make sure that the device is not exposed to extreme heat or in small area. Power supply Connect the fixture to the mains.

  • Page 5: Example Of Connection

    Example of connection Example 1: The DMX signal is generated by a DMX controller, the signal cable goes in and out from each projector up to the last one. The projectors will execute the same scenes if the DMX addresses are the same (factory set is 1) or they can be driven one by one if the DMX addresses are different from each other.
  • Page 6 Standard DMX controllers have only one signal out-put. If more than 32 projectors are used it is necessary to have a signal SPLITTER, that will duplicate the signal in 2 or more lines. If the signal cable is very long, it is necessary to install a signal AMPLIFIER on the DMX line (at least every 300m of good quality cable), so that it will repeat the signal to the following projectors.

  • Page 7: User's Interface

    User’s interface The LED lighted indicates the presence of DMX signal. The LED flashing indicates the absence of DMX signal. To modify the DMX address and the settings, it is necessary to move the dip-switches on ON or OFF position, following the tables and the drawings of this manual.
  • Page 8 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9...
  • Page 9 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9...
  • Page 10 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9...
  • Page 11 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9 DMX Dip1 Dip2 Dip3 Dip4 Dip5 Dip6 Dip7 Dip8 Dip9...

  • Page 12: Stand Alone Mode (Colour Sequence)

    Stand alone mode (colour sequences) For the stand alone mode (STAND ALONE/MASTER), the dip-switch 12 has to be on the ON position. When the projector is switched on, it will execute the functions set on the dip-switches. If the projector has to execute colour sequences, the dip-switches 12 has to be on ON position. WARNING: The projector in stand alone mode becomes a DMX generator, it is necessary to disconnect that projector by DMX controller or by the other projector MASTER because generates conflict in the signal.
  • Page 13 COLOUR HOLDING TIME SETTING Setting the dip-switches 7, 8, 9, 10, 11, it is possible to choose the colour holding time (from 5 seconds to 8 hours). Dip 7 Dip 8 Dip 9 Dip 10 Dip 11 Seconds Minutes Hours...

  • Page 14: Lamp Replacement

    Lamp Replacement • Disconnect the projector from the main power supply. • Unscrew the 4 screws that hold the protection of the lamp holder. • Unscrew the 3 screws and remove the lamp holder • Remove the lamp, taking care to wear proper protective gloves. •...

  • Page 15: Spare Parts

    Spare parts When ordering spare parts for the projector remember to mention the model and serial number which can be found on the plate at the rear of the projector. Call your area dealer or feel free to contact the manufacturer for any additional assistance. SPARE PART LIST CODE DESCRIPTION...

This manual is also suitable for:

Msd 250w

Table of Contents