3) When changing from ALPS (connector ; pin 7) cylinder to SEM (connector ; pin 5) cylinder. - Change CN605 (Connector ; pin 7 pin 5) - Change CN605B (Cable-Flat ; pin 7 pin 5) 4) After replacing the “SEM Cylinder”, use type “C, D, G, H” optional for “NVRAM Option Setting”. (See page 5-9) Toshiba...
Page 4
3) When replacing the TM-Block as a service parts, be sure to replace only the TM-Block which is SIF available. The only part-no of “SIF available” is shown in the “CH7. Replacement Parts List” of Service Manual. 4) After replacing “TM-Block”, use type “B, D, F, H” optional for “NVRAM Option Setting” regardless of VR501. (See page 5-9) Toshiba...
Page 5
Alternatively, wear a discharging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Toshiba...
Page 6
Always inspect for pinched, out- of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. Toshiba...
Line input : 308 mV(rms), more than 47 Kohm, pin jack Audio output Line input : 308 mV(rms), more than 47 Kohm, pin jack Audio frequency range(Hi-Fi) 20Hz - 20KHz Audio dynamic range(Hi-Fi) 68dB Utilization conditions Temperature : 5°C to 40°C Humidity : less than RH 80% Toshiba...
Hook. Fig. 4-1 Cabinet Top Removal CN701 4-1-2 Ass’y Front Panel Removal CN703 Fig. 4-3 Jack PCB/Key PCB Removal Œ RELEASE 4 HOOKS (Top View) ´ RELEASE 2 HOOKS (Bottom View) Fig. 4-2 Ass’y Front Panel Removal Toshiba...
Page 24
When installing the ass'y full deck on the Main PCB, be sure to align the assembly point of mode switch. MODE SWITCH ASSEMBLY POINT Œ REMOVE 2 SCREWS ´ REMOVE BRACKET-FRAME Ø LIFT THE ASS'Y MAIN PCB UP TO REMOVE. ˇ REMOVE 2 SCREWS Fig. 4-4 Chassis Removal Toshiba...
Page 25
¨ Ø ∏ Fig. 4-5 Top parts Location-1 Œ BRACKET FL TOP (Optional) ´ GEAR FL CAM ˇ MOTOR LOADING ASS’Y ¨ LEVER FL ARM ASS’Y ˆ HOLDER FL CASSETTE ASS’Y Ø LEVER FL DOOR ∏ SLIDER FL DRIVE Toshiba...
Page 26
Ò GEAR IDLE ¨ PLATE CYLINDER B Ú LEVER IDLE ˆ PLATE CYLINDER A Æ LEVER T BRAKE ASS’Y Ø ACE HEAD ASS’Y ı DISK T REEL ∏ UNIT PINCH ASS’Y ” LEVER #9 GUIDE ASS’Y ’ LEVER TENSION ASS’Y Toshiba...
Page 27
Œ GEAR JOINT 1 ´ GEAR JOINT 2 ˇ BRAKET GEAR ¨ MOTOR CAPSTAN ASS’Y ˆ LEVER T LOAD ASS’Y Ø GEAR LOADING DRIVE ∏ LEVER S LOAD ASS’Y ” HOLDER CLUTCH ASS’Y ’ BELT PULLEY ˝ SLIDER CAM Ô SLEEVE TENSION Toshiba...
Page 28
Note : Take care not to change assembly direction. in the direction of arrow “B”. Œ 2 SCREWS Œ LEVER FL DOOR ´ BRACKET FL TOP "A" "B" ´ HOOK Fig. 4-9 Lever FL Door Removal Fig. 4-8 Braket FL Top Removal Toshiba...
Page 29
´ BOSS ˇ SLIDER FL DRIVE "B" Fig. 4-11 Lever FL Arm Ass’y Removal BOSS [B] RAIL [C] Œ HOLDER FL RAIL [D] CASSETTE ASS'Y ´ LEVER FL CASSETTE-R "A" BOSS [A] Fig. 4-10 Holder FL Cassette Ass’y Removal Toshiba...
Page 32
Œ GEAR LOADING DRIVE HOOK [A] ´ SLIDER CAM ˇ LEVER T LOAD ASS'Y ¨ LEVER S LOAD ASS'Y Œ SCREW Fig. 4-16 Motor Loading Ass’y Removal Fig. 4-17 Gear Loading Drive, Slider Cam, Lever T, S Load Ass’y Removal 4-10 Toshiba...
Page 33
PIN A PIN C PIN D PIN B ˇ SLIDER CAM Fig. 4-18 Assembly of Gear Loading Drive, ´ SLEEVE TENSION Slider Cam, Lever T, S Load Ass’y Fig. 4-19 Lever Tension Ass’y, Band Brake Ass’y, Sleeve Tension Removal Toshiba 4-11...
Page 34
ˇ SPRING BRAKE HOOK [A] HOOK [C] ´ GEAR IDLE "B" ´ LEVER T BRAKE ASS'Y Œ LEVER S BRAKE ASS'Y ´ GEAR IDLE HOOK [B] Fig. 4-21 Lever Idle Ass’y Removal Fig. 4-20 Lever S, T Brake Ass’y Removal 4-12 Toshiba...
Page 35
Gear Center Ass’y as shown in detail B. Œ WASHER SLIT ´ HOLDER CLUTCH ASS'Y Fig. 4-22 Disk S, T Reel Removal DETAIL A SPRING <GOOD> <BAD> DETAIL B SPRING <GOOD> <BAD> Fig. 4-23 Holder Clutch Ass’y Removal Toshiba 4-13...
Page 36
ˆ GUDIE Œ LEVER UP DOWN ASS'Y ¨ RING ˇ GEAR ∏ HOOK 35˚ Ø POST MAIN BASE Fig. 4-25 Assembly of Lever Up Down Ass’y, Gear Center Ass’y Fig. 4-24 Lever Up Down Ass’y, Gear Center Ass’y Removal 4-14 Toshiba...
Page 37
2) When reinstalling, be sure to apply grease on the post pinch roller. HOOK [A] ´ PLATE JOINT Œ UNIT PINCH ASS'Y ˇ SPRING PINCH DRIVE Fig. 4-26 Guide Cassette Door Removal Fig. 4-27 Unit Pinch Ass’y, Plate Joint, Spring Pinch Drive Removal Toshiba 4-15...
Page 38
2) After reinstalling, check the bottom side of the Post #9 Guide to stick to the top side of Main Base. ´ LEVER #9 GUIDE ASS'Y Œ SPRING #9 GUIDE Fig. 4-29 FE Head Removal Fig. 4-28 Lever #9 Guide Ass’y Removal 4-16 Toshiba...
Page 39
2) Remove the screw Œ. 3) Lift the ACE Head Ass’y ´. Œ SLIDER S ASS'Y Œ SCREW ´ SLIDER T ASS'Y ´ ACE HEAD ASS'Y Fig. 4-31 Slider S, T Ass’y Removal Fig. 4-30 ACE Head Removal Toshiba 4-17...
Page 40
Plate Cylinder C ´. ∏ CYLINDER ASS'Y ˆ SCREW Œ SCREW ´ PLATE CYLINDER C ˇ SCREW ¨ PLATE CYLINDER B Ø PLATE CYLINDER A Fig. 4-33 Belt Pulley Removal Fig. 4-32 Cylinder Ass’y Removal 4-18 Toshiba...
Page 41
4) Rotate Gear Worm Wheel ˇ counterclockwise using screw driver again up to the state of eject mode and then pick out the tape. (Refer to Fig. 4-35) ´ MOTOR CAPSTAN ASS'Y Fig. 4-34 Motor Capstan Ass’y Removal FRAME Fig. 4-36 Toshiba 4-19...
Page 42
∆ CAPSTAN MOTOR PULLEY BELT PULLEY ∆ HOLDER CLUTCH ASS’Y GEAR CENTER ASS’Y GEAR IDLE (2Point) LOADING MOTOR BAND BRAKE ASS’Y BRAKE T ASS’Y ◆ : Add Oil ∆ : Cleaning O : Check and replacement in necessary 4-20 Toshiba...
- If the corresponding adjustment button is pressed, the adjustment is preformed automatically. - If the adjustment is completed, be sure to turn the power off. 5-1-1 Location of adjustment button of remote control X-Point (Tracking Center) Adjustment Head Switching Adjustment NVRAM Option Setting Fig. 5-1 Toshiba...
Page 44
Alignment and Adjustment 5-1-2 Test point location for adjustment mode setting Short-Circuit Fig. 5-2 Main PCB (Top View) Toshiba...
Fig. 5-3 Location of Tape Transport Adjustment FE HEAD CYLINDER ASS'Y PINCH ROLLER GUIDE ROLLER "S" GUIDE ROLLER "T" POST TENSION #8 GUIDE POST #9 GUIDE POST MAIN BASE ACE HEAD CAPSTAN SHAFT #3 GUIDE POST Fig. 5-4 Tape Travel Diagram Toshiba...
Page 46
Test point : TP601 (Control Pulse) TP602 (H’D S/W -Trigger) TP301 (Envelope) TP302 (Audio output) TP303 (Video output) Test tape : ST-N1 BLANK TAPE : T-160 AUDIO OUTPUT ENVELOPE HEAD SWITCHING Fig. 5-5 Location of Test point (Main PCB-Top View) Toshiba...
Page 47
4) Connect the CH-1 probe to TP301 (Envelope) the CH-2 probe to TP602 (H’D switching pulse) and then trigger to CH-1. 5) Insert the (-) driver into the X-Point adjustment hole and adjust it so that envelope wavwform is maximum. 6) Turn the Power off. Toshiba...
Page 48
) driver to obtain a flat video RF envelope as shown in Fig. 5-11. IDEAL ENVELOPE S HEIGHT S HEIGHT T HEIGHT T HEIGHT TOO HIGH TOO LOW TOO HIGH TOO LOW GUIDE ROLLER T GUIDE ROLLER S Fig. 5-11 Guide Roller S, T Height Adjustment Toshiba...
Page 49
T-120 (E-120). The video envelope should meet the specification as shown in Fig. 5-13. In SP mode, (A) should equal (B). If the head gap is wide, upper cylinder should be checked. Fig. 5-13 Envelope Output and Output Level Toshiba...
Page 50
2) Be careful not to deform the region of adjusting on Fig. 5-14 Main Base up and down at adjusting. ¨ GEAR FL CAM TIMING POINT ˇ SLIDER FL DRIVE ´ GEAR WORM WHEEL Fig. 5-15 Toshiba...
<Table 5-2> How to identify the Type MODEL TYPE OPTION NUMBER Assy-Cylinder Capstan Motor VR501 W-603 2, 3, 6, 8, 9, 12, 16 Type ALPS Sankyo None 2, 3, 6, 8, 9, 12 2, 3, 6, 8, 12, 16 •...
Page 52
How to identify the Assy-Cylinder ALPS Cylinder SEM Cylinder CONNECTOR ; Pin 5 CONNECTOR ; Pin 7 or Pin 5 Fig. 5-19 How to identify the Capstan Motor TOP VIEW SANKYO CAPSTAN MOTOR SEM CAPSTAN MOTOR CAPSTAN SHAFT CAPSTAN SHAFT Fig. 5-20 5-10 Toshiba...
Page 53
Alignment and Adjustment Location for VR501 VR501 Fig. 5-21 Main PCB (Top View) Toshiba 5-11...
Important safety notices : Components identified with the mark have the special characteristics for safety. When replacing any of these components. Use only the same type. ◆ Block Identification of Main PCB 10-2 Toshiba...
Page 76
5V when the front video jack is inerted VCR:5, TV:0 5p-p 5p-p Clock data Safety Tab, YES:5, NO:0 5p-p 5p-p 5p-p 5p-p for Hi-Fi/EEPROM/PLL data,clock 5p-p 5p-p data for LED display 5p-p Video out signal 5p-p 5p-p 5p-p 5p-p Video input signal Toshiba 10-5...
Page 78
0.7 0.7 Video Out Video Out 0.7 0.7 0.8p-p 0.8p-p Video from L1(rear) 4.4 1.8 0.8p-p 0.8p-p 4.4 1.8 Video from L2(front) 4.4 1.8 4.4 1.8 Video from TM-block 1.7 0.3 0 2.7 1.2 0 2.4 2.4 2.5 2.5 Toshiba 10-7...
Page 80
Audio R from front jack (option) 5p-p for Hi-Fi data,clock 5p-p 5p-p Audio to TM-block 2.5 2.5 Audio R from rear jack (L1) 2.5 2.5 Audio L from front jack (option) 2.3 2.3 Audio from TM-block 0.7 0.7 Toshiba 10-9...