Maintenance; Cleaning The Bath; Repairs To The Surface; Bath Additives - Jacuzzi Finestra FL61000 Installation & Operation Instructions

Cleaning the Bath

To clean your bath, simply use a mild, nonabrasive liquid
detergent solution. You can protect and restore the gloss to a
dulled acrylic surface by applying Meguiar's #10 Mirror Glaze,
a product specifically designed for use on acrylic finishes. If
Meguiar's is not available, an acrylic polish of equal quality or
automotive paste wax is acceptable.
never use abrasive household cleaners on any Jacuzzi
Whirlpool Bath product.

repairs to the surface

Minor scratches which do not penetrate the color finish can be
removed by lightly sanding with 600-grit wet/dry sandpaper.
Restore the gloss using Meguiar's Mirror Glaze or automotive
paste wax.
Major scratches and gouges which penetrate the acrylic
surface will require refinishing. Ask your Jacuzzi Whirlpool
Bath dealer for special instructions.

Bath additives

note: Do not use oil or oil-based bath additives.
If you want to use any kind of bath additive, use only a small
amount of low-foaming powder or crystal substance; the
whirlpool action intensifies the foaming properties of soaps.
The use of certain bath oils, bubble baths and bath additives
may increase the level of accumulations of bath residue in the
whirlpool system. If excess accumulations persist, you should
discontinue use of these products.

Purging the Whirlpool system

note: The Whirlpool System should be purged at least twice
a month.
To remove accumulations of bath residue from the whirlpool
system, it is recommended that a whirlpool bath be purged
at least twice a month. For best results, however, we
recommend that you purge your whirlpool bath after each
use using, Systems Clean™, our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.
Systems Clean™ is available through an authorized Jacuzzi
Whirlpool Bath distributor or by calling us direct at 1-800-288-
4002.
Jacuzzi Whirlpool Bath: finestra Walk-in Bath

MaintenanCe

systems Clean™ instructions
Refer to the instructions on the Systems Clean™ packet.
CaUtion: Do not use while bathing! Use extreme caution
when handling this product!
Immediately after bathing and exiting the whirlpool bath,
leave the bath water in the tub and add more hot water. The
water level in the tub must be at least 2" (5,08 cm) above the
highest jet.
note: Inducted air from the hydromassage system will cause
the Systems Clean™ contents to foam increasing odor.
Turn OFF the whirlpool air control or turn it to the lowest
setting and pour in the entire contents of PACkET #1 ONLY
directly into the bath water. For best results, pour the System
Clean into the tub near the intake for the circulation pump and
be sure to avoid contact with your skin. Allow the whirlpool
to run for 30 seconds and then add PACkET #2 ONLY. it is
important to use Packet #1 before Packet #2 to avoid a
strong odor. Allow the bath to run for 5 to 10 minutes then
drain the tub completely. Refill the tub with cold water and run
for 2 to 3 minutes. Drain completely and rinse off any residue.
Remember to reset the air valves to your bathing comfort
level.
Danger: Harmful if swallowed. Eye irritant. Protect your
eyes, skin and mucus membranes from contact with this
product or its concentrated solution. A strong alkaline product
can cause severe burns to the eyes and skin.
If you have followed the standard purging instructions above
and still have an excess accumulation of bath residue and
desire an alternative cleaning mechanism, we recommend
sUPer sYsteMs Clean™ PlUs manufactured by Stearns
Packaging to rectify this condition. This may be obtained by
contacting us at 1-800-288-4002. It is recommended that
you follow the instructions provided by the manufacturer
with the product. Repeated use may be necessary. sUPer
sYsteMs Clean™ PlUs does not replace the necessity to
regularly purge your whirlpool system with Systems Clean™
as recommended.

ozone Maintenance

The PrO 3 Ozone Sanitation System is a maintenance-free
system. All that is required is the regular system cleaning
using the Systems Clean™ as directed.
Page 1 fl61000B • 10/07