Starting The Program; Progress Of Program; Childproof Lock; Changing The Selections After The Program Has Started - Beko WMB 51031 CS PT User Manual

Additional laundry may be loaded during the
C
time delay period.
5. The selected program duration is displayed
at the end of the countdown process.
"_" symbol disappears and the selected
program starts.
Changing the delay time
If you want to change the time during the
countdown:
1. Press the time delay button. Every time the
button is pressed, the time will be increased
in 1-hour increments.
2. If you wish to shorten the time delay, keep
on pressing the time delay button until the
time delay you would like to set appears on
the screen.
Canceling the time delay
If you want to cancel the time delay countdown
and start the program:
1. Set the Time Delay to zero or turn the
Program selection knob to any program.
Thus, the time delay will be cancelled. The "
" (End/Cancel) light flashes continuously.
Then, select the program you wish to run
again.
2. Press "Start/Pause" button to start the
program.

Starting the Program

1. Press "Start/Pause" button to start the
program.
2. Program follow-up lamp showing the startup
of the program will light up.
If no program is started or no key is pressed
C
within 1 minute during program selection
process, the machine will switch to "Stand-
by" mode and the illumination level of the
temperature, speed and door indicators
will decrease. Other lights and indicators
will turn off. In case of turning the program
selection knob or pressing any button, lights
and indicators will turn on.

Progress of program

Progress of a running program is shown through
the program follow-up indicator. At the beginning
of every program step, the relevant indicator LED
will light up and light of the completed step will
turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
program flow while the program is running.
However, the change to be made must be
compatible with the program step the machine
is currently in. If the change is not compatible,
relevant lights will flash for 3 times.
If the machine is not spinning, the program
C
may be in rinse hold mode or the automatic
spin correction system has been activated
due to an excessive unbalanced distribution
of laundry in the machine.
Changing the selections after the
program has started
Switching the machine to standby mode
Press the "Start/Pause" button to switch the
machine to pause mode while a program is
running. The light of the step which the machine
is in starts flashing in the program follow-up
indicator to show that the machine has been
switched to the pause mode. Also, when the
door is ready to be opened, "Door" light will also
illuminate continuously in addition to the program
step light. If necessary conditions to open the
door are not met, the "Door" light will remain off.
Changing the speed and temperature set-
tings for auxiliary functions
Auxiliary functions can be cancelled or selected,
or the spin speed and temperature settings can
be changed in accordance with the step the
program is in. If the change can not be made,
relevant light will flash for 3 times.
Adding/removing laundry in pause mode
If the "Door" light flashes while the machine is in
pause mode, it means that the conditions (low
water level, etc.) to open the door have been
met and the period of approx. 1 or 2 minutes to
open the door has started. "Door" lamp will light
up continuously when the door is unlocked. Door
can be opened to load or unload the laundry
after this moment. If the front door cannot be
opened because of a safety reason after the
machine has been switched to the pause mode
by pressing the "Start/Pause" button, the "Door"
light will continue to remain off. Nevertheless, the
follow-up light of the relevant program in which
the machine was taken to "Pause" mode will
flash.

Door lock

The loading door can be opened once the
"Door" lamp stops flashing and starts lighting up
continuously.
Child-proof lock
Protect the appliance from being tampered by
children by means of the child-proof lock. In this
case, no change can be made in the running
program.
If the program selection knob is turned when
C
the child-proof lock is activated, "Con" label
will be displayed. In this case, any change in
temperature, speed and auxiliary functions
which are already selected for the programs
is not allowed.
If the program selection knob is turned to
C
"On/Off" position and then another program
is selected while a program is running, the
previously running program will resume
operating.
The machine is switched to child-lock by
pressing the 1st and 2nd auxiliary functions for
3 sec. While the lights on the auxiliary function
9 - EN