Related Manuals for Sur-e slice SSG300PTR/B
Summary of Contents for Sur-e slice SSG300PTR/B
- Page 1 Professional slicer CE SSG300PTR/B mod. Operating and Maintenance Manual SERVICE CENTRE AUTHORISED DEALER...
-
Page 3: Chap. 8 - Dismantling
INTRODUCTION CHAP. 8 - DISMANTLING This manual has been re-presented to provide the Client with all the 8.1 - OUT OF SERVICE information on the machine and its safety regulations, and also the use and If for some reason it is decided to put the machine out of service, make sure that maintenance instructions which permit using the machine in the best way it cannot be used by anyone: detach or cut the electrical connections. -
Page 4: Chap. 7 - Maintenance
CHAP. 5 - MACHINE USE page 19 CHAP. 7 - MAINTENANCE - OPERATIONAL CHECK - LOADING AND CUTTING THE PRODUCT 7.1 - GENERALITIES - SHARPENING THE BLADE Before carrying out any maintenance operations it is necessary to: a) disconnect the feed plug from the electrical network to completely isolate CHAP. - Page 5 6.2.3 - Cleaning the sliceguard (Fig. CHAP. 1 - RECEIVING THE MACHINE n°51) To remove the sliceguard simply grasp 1.1 - PACKAGE the handgrip (1) and pull up so that the two pins unhook (2), and then extract the sliceguard. The slicer is shipped in a package which consists of (Fig.
- Page 6 with warm water, equipped detergent or neutral detergent (pH 7) Do not expose the package to humidity Fig. n°47. or rain (Fig. n°4). Fig. n°47 Fig. n°4 6.2.2 - Cleaning the blade, the bladeguard and the ring Unscrew the blade cover tie rod (3) and remove the blade cover (2) (Fig.
-
Page 7: Chap. 2 - Installation
grinders and the blade (chapter overturn the package!! When transporting it make sure that it is firmly held by the four corners (keeping it parallel to the floor 6.2.3); 9. once operation finished, replace the sharpening device in its original position, doing the procedure CHAP. - Page 8 2.2 - therefore the cutting effort increases (chapter 5.3). POSITIONING Position the pallet, with the slicer, on a 5.3 - SHARPENING THE BLADE flat surface and take off (a) the sharpener from the slicer (Fig. n°12). WARNING: Before starting to sharpen the blade, pay attention to At this point turn the machine on its RESIDUAL RISKS (chapter 4.2.2) concerning the dangers of cutting without side (Fig.
-
Page 9: Loading And Cutting The Product
5.2 - LOADING AND CUTTING THE PRODUCT 2.3 - ELECTRICAL CONNECTION WARNING: The goods to be cut are loaded on the plate only with the graduated Check that the data reported on the handgrip at “0” and the motor stopped, being careful with the blade and the technical-part number plate (Fig. -
Page 10: Operational Check
the position of two of the three phase CHAP. 5 - MACHINE USE wires (black, gray or brown) in the plug. 5.1 - OPERATIONAL CHECK For the 1° use follow these instructions: Fig. n°20 check that installation has been carried out correctly as in chapter 2; 2.3.5 - Electrical connection modification check that the plate is well fastened Unless otherwise specified, the slicers are equipped with 400 V. - Page 11 2.4.1 - 115 V. tension selection 2.4.2 - Single-phase 220-240 V. tension selection Fig. n°34 2.4.3 - Three-phase 230 V. tension selection TAB. n°1 - DIMENSION MEASUREMENTS AND TECHNICAL FEATURES Model U.m. SSG300PT Diameter blade Motor Watt/Hp 275/0,37 Cut thickness Run of carriage Hopper 305x270...
-
Page 12: Preliminary Check
2.5 - PRELIMINARY CHECK - A relay in the control circuit, that requires the machine to start up again Before testing make sure the goods in case of an accidental loss of holder plate is well-blocked, after which electricity (Fig. n°33). test functioning with the following procedure: Push the “ON”... -
Page 13: Safety Devices Installed On The Machine
4.2 - SAFETY DEVICES INSTALLED ON THE MACHINE The slicer must only be used by trained personnel who know the 4.2.1 - Mechanical safety safety norms contained in this manual As far as mechanical safety is concerned, the slicer described in this manual perfectly. -
Page 14: Construction Features
Do not pull the slicer or the feeding LEGEND: cable (Fig. n°29) to unplug it. Sharpener handgrip Blade protection Regularly check the state of the Sharpener Base feeding cable; a worn out cable or in any case not intact represents a Thickness gauge plane Extractable pin serious electrical danger.
Need help?
Do you have a question about the SSG300PTR/B and is the answer not in the manual?
Questions and answers