Related Manuals for Jonsered FR2218FA
Summary of Contents for Jonsered FR2218FA
- Page 1 Oper ator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine. FR 2216 F A FR 2218 FA 4X4...
-
Page 2: Table Of Contents
CONTENTS Contents Checking and adjustment of the cutting unit’s ground pressure ............... CONTENTS Checking the cutting unit’s parallelism ......Contents ..............Adjusting the parallelism of the cutting unit ....INTR ODUCTION Service position for the cutting unit ......Dear Customer , ............Checking the blades ............. -
Page 3: Intr Oduction
Dear Customer , Thank y ou for choosing a Jonsered Frontrider. Jonsered Frontriders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. FrontRiders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine. -
Page 4: Ser Vice Journal
Ser vice journal Pre-deliver y service 1 Charge the battery for 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure (60 Kpa, 0.6 bar, 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb). -
Page 5: Key To Symbols
KEY T O SYMBOLS Symbols Noise emission to the environment according to the European Community’s Directive. The machine’s emission is These symbols are on the machine and in the instr uctions. specified in chapter Technical data and on label. WARNING! Careless or incorrect use can result in serious or fatal injury to the Clutch in operator or others. - Page 6 KEY T O SYMBOLS Chec k the engine’s oil level Check transmission oil level Lift up the cutting unit Apply the parking brake. If the engine is cold, use the choke Release the parking brake before driving 6 – English...
-
Page 7: Wha T Is What
WHA T IS WHA T? Location of the contr ols 1 Throttle control/choke control 9 Product and serial number plate 2 Ignition lock 10 Seat adjustment. 3 Cutting height adjustment lever 11 Lever to disengage the driving front axle FR 2218FA 4X4 4 Lifting lever for the cutting unit 12 Fuel cap 5 Speed limiter for reversing... -
Page 8: Safety Instr Uctions
SAFETY INSTR UCTIONS Saf ety instructions • Stop the engine and prevent the engine from being started until you have cleaned the outlet channel. These instr uctions are for your safety. Read them carefully. • Look out for the ejector and do not direct it towards anyone. -
Page 9: Driving On Slopes
SAFETY INSTR UCTIONS This is what y ou do • Never allow children or other persons not trained in the use of the machine to use or service it. Local laws may • Remove obstacles such as stones, branches, etc. regulate the age of the user. -
Page 10: Children
SAFETY INSTR UCTIONS • Follow the manufacturer’s recommendations regarding • Petrol and petrol fumes are poisonous and extremely wheel weights or counterbalance weights to increase flammable. Be especially careful when handling petrol, as machine stability. carelessness can result in personal injury or fire. •... -
Page 11: Transport
SAFETY INSTRUCTIONS • Do not change the setting of governors and avoid running Engage the parking brake and tie the tension belts around the engine at excessively high revs. If you run too fast, you stable parts on the machine, e.g. frame or rear wagon. risk damaging the machine components. -
Page 12: Presentation
PRESENTATION Presentation The parking brake lock disengages automatically when the brake pedal is pressed. Congratulations on your choice of an excellent quality product that will give you great pleasure for many years. FR 2218 FA Cutting unit 4X4 is equipped with all wheel drive. FR 2216FA and FR 2218FA 4x4 can be equipped with two The power transmission from the engine is handled by a different cutting units. -
Page 13: Seat
PRESENTATION Combi-unit 40-90 mm (1 9/16” - 3 9/16”) Pull the controls to the end positions, do not use an intermediate position. Release lever FR 2218FA 4X4 FR 2218 FA 4X4 has one control for the front axle and one control for the rear axle. -
Page 14: Driving
Driving Before starting Move the throttle to position 3 (choke position). In this position the engine is fed with a richer mixture, which means the engine is easier to start. IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. -
Page 15: Starting The Engine With A Weak Battery
Driving Let the engine run at moderate speed or half throttle for 3- • Finally the RED cable from both batteries. 5 minutes before subjecting it to heavy load. When mowing, use 3/4 to full throttle. Driving the Rider 1 Release the parking brake by first pressing down the WARNING! Never run the engine indoors, in parking brake pedal and then releasing it. -
Page 16: Cutting Tips
Driving Cutting tips 1 Lift up the cutting unit by pulling the lever backwards to its locked position. • Localise and mark stones and other fixed objects to avoid collision. Pull back the throttle and turn the ignition key to the •... -
Page 17: Maintenance
Maintenance Maintenance schedule The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised service workshop. Daily maintenance At least once Maintenance Maintenance before starting a year interval in hours 100 200... -
Page 18: Cleaning
Maintenance Cleaning Right-hand fender Remove the accelerator knob (1), screws (2), and remove the Clean the machine directly after use. It is much easier to wash cover. off grass cuttings before they dry. Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer. -
Page 19: Adjusting The Parking Brake
Maintenance FR 2218FA 4X4 1 Remove the frame plate by loosening the screws (2) and lift the frame plate by the rear edge. 1 Remove the left-hand wing cover. 2 Loosen the locking nuts (1). 2 Check the tension of the steering wires by pushing them together (at the arrows). -
Page 20: Replacement Of Fuel Filter
Maintenance 1 Loosen the clamping screw for the cable’s outer casing 4 Press the new filter into the ends of the hoses. If and move the throttle to the full throttle position. necessary apply liquid detergent to the ends of the filter to facilitate connection. -
Page 21: Checking The Fuel Pump's Air Filter
Maintenance 7 Align the tabs on the cover with the slits in the housing and 4 Measure the electrode gap with a gapping tool. The gap replace the air filter cover. should be 0.75 mm/0.030”. Adjust as necessary by bending the side electrode. 5 Reinsert the spark plug, turning by hand to avoid damaging the threads. -
Page 22: Check The Safety System
Maintenance Check the safety system Start motor The machine is equipped with a safety system that prevents starting or driving under the following conditions. Ignition system The engine should only be possible to start when the cutting unit is in its raised position and the gear shift lever or hydrostat pedals are in the neutral position. -
Page 23: Main Fuse
Maintenance Main fuse Check that the cooling intake is free from leaves, grass and dirt. The main fuse is placed in a detachable holder under the battery case’s cover, in front of the battery. Type: Flat pin, 15 A. Check the air duct, located on the inside of the engine cover, ensure it is clean and does not rub against the cooling air Do not use any other type of fuse when replacing. -
Page 24: Checking The Cutting Unit's Parallelism
Maintenance Checking the cutting unit’s Service position for the cutting unit parallelism The cutting head can be placed in the service position to provide easy access for cleaning, repairs and servicing. In the Check the cutting unit’s parallelism as follows: service position the cutting unit is raised and locked in the vertical position. -
Page 25: Checking The Blades
Maintenance 5 Remove the drive belt and place it in the belt holder. 2 Tension the belt with the belt adjuster. 6 Grip the front edge of the unit and pull forwards until it Fit the front cover. stops. Checking the blades To achieve the best mowing results it is important that the blades are undamaged and well-sharpened. -
Page 26: Lubrication
Lubrication Checking the engine’s oil level. 2 Remove the dipstick. Remove the drain plug from the engine’s left side. Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Open the engine cover. Loosen the dipstick, pull it up and wipe it off. -
Page 27: Lubricating The Belt Adjuster
Lubrication Lubricating the front wheel bearings Work on the system entails particular demands on cleanliness and the system must be vented before the machine is used. The front cover and wing covers must be removed on Rider with rear ejection, so that the tubular loop can be lifted to remove the wheel. -
Page 28: Troubleshooting Schedule
Troubleshooting schedule Problem Procedure Engine does not start There is no fuel in the fuel tank Spark plug defective Faulty spark plug connections or interchanged cables Dirt in the carburettor or fuel line Dirt in the carburettor or fuel line Starter motor does not turn over the engine Battery flat Bad contact between the cable and battery Lift lever for cutting unit in wrong position... -
Page 29: Storage
Storage Winter storage Service At the end of the season, or if the machine is going to stand Low season is the most suitable time to perform a service or idle for more than 30 days, it should immediately be made overhaul of the machine in order to ensure high function ready for storage. -
Page 30: Technical Data
TECHNICAL DATA FR 2216 FA FR 2218FA 4X4 Dimensions Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 890/2,92 890/2,92 Height, mm/ft 1150/3,77 1150/3,77 Operating weight with cutting deck, kg/lb 271-274/597-604 292-295/644-650 Wheel base, mm/ft 887/2,9 887/2,9 Track width, front, mm/ft 712/2,34 712/2,34... -
Page 31: Ec-Declar Ation Of Conformity
EC-declaration of conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Jonsered FR 2216 FA and FR 2218 FA 4X4 from 2010’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE:... - Page 32 Original instructions 1153120-26 ´®z+U,"¶6C¨ ´®z+U,"¶6C¨ 2009-12-22...