Table of Contents
Advertisement
Sys tem Check list & Trou ble shoot ing (Con tin ued)
Step 3. (Continued)
Test the chirps.
NOTE: If the 20A fuse blows upon arm ing:
n
Disconnect the ACE 2000's two parking light wires, replace the 20A fuse and rearm. If
the fuse blows while the parking light wires are dis con nected, the door locks are not
wired cor rectly. Re con nect the ve hi cle's power lock ing sys tem to its origi nal con di tion,
then re test the volt ages as in di cated in the Door Locks sec tion of this binder and wire the
locks as in di cated, then re place the 20A fuse.
Step 4.
Test the park ing lights.
Arm the sys tem by press ing the
Two flashes. This is the correct response, proceed to step 5.
n
n
One flash. If the parking lights flash only once, the ACE 2000 had pre vi ously
AutoArmed it self pas sively and by press ing the but ton the sys tem dis armed (re mote
dis arm ing is ac knowl edged with one chirp and one parking light flash). Disarm and
rearm the system.
n
No flashes. If no flashes, ver ify the parking light bulbs are op era tional. If not, they must
be re placed. If so, re peat steps 1-5 of the Parking Lights sec tion at the end of this manual.
Only one side flashes. If only the right or the left side parking lights flash, see the
n
Parking Lights sec tion at the end of this manual.Sys tem Check list & Trou ble shoot ing
(Con tin ued)
Step 5.
Test the door locks.
Arm the sys tem by press ing the
n
Doors lock. This is the correct response, proceed to step 6.
n
Doors do not lock. You ei ther se lected the wrong door lock dia gram , con nected the
wires in cor rectly, or a servo may be required. Re con nect the ve hi cle's power lock ing
sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door
Lock ing/Un lock ing sec tion of this binder and wire the locks as in di cated. Polarity
programming should also be verified.
WARN ING: If the doors do not lock, DO NOT ac ti vate the ve hi cle's lock
switches. If the locks have been mis wired, do ing so may dam age the ACE
2000 con trol unit, the ve hi cle's elec tri cal sys tem and/or the power lock servo
mo tors.
Doors unlock. You ei ther se lected the wrong door lock dia gram, con nected the wires
n
in cor rectly, or a servo may be required. Re con nect the ve hi cle's power lock ing sys tem to
its origi nal con di tion, then re test the volt ages as in di cated in the Door
Lock ing/Un lock ing sec tion of this binder and wire the locks as in di cated.
n
Only one door locks. You ei ther se lected the wrong door lock dia gram, con nected the
wires in cor rectly, or a servo may be required. Re con nect the ve hi cle's power lock ing
sys tem to its origi nal con di tion, then re test the volt ages as in di cated in the Door
Lock ing/Un lock ing sec tion of this binder and wire the locks as in di cated.
Step 6.
Test the LED.
Arm the system by pressing the
n
Flashes repeatedly. This is the correct response, proceed to step 7.
n
No flashes. If the LED does not flash, ver ify that the LED's VIO LET and BLACK wires
are sol idly con nected to the same color wires on the ACE 2000's wire loom. Warn ing:
This is a 2- volt LED, test ing with 12 volts will de stroy the LED.
but ton on the re mote con trol.
button on the re mote con trol.
button on the remote control.
19
Advertisement
Table of Contents
