DG-SC7100P-10 Day/Night SPEED DOME POE IP Camera with IR CUT FILTER and 10x OPTICAL ZOOM User Manual V1.0 2012-06-22 As our products undergo continuous development the specifications are subject to change without prior notice...
Page 2
Trademarks: DIGISOL™ is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property of the respective manufacturers. Safety This equipment is designed with the utmost care for the safety of those who install and use it.
DG-SC7100P-10 User Manual Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable protection against harmful interference in a residential installation.
DG-SC7100P-10 User Manual FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.
DG-SC7100P-10 User Manual INDEX 1. Product Information....................... 8 1-1 Product Introduction ....................8 1-1 Safety Instructions....................... 9 1-2 System Requirements ....................10 1-3 Package Contents..................... 11 1-4 Get Familiar with your new Network Dome Camera ........... 12 1-5 Installation of the Network IP Camera..............
Page 6
DG-SC7100P-10 User Manual 3‐5‐2 Video Setting......................51 3‐5‐3 Overlay Setting ......................54 3-6 Audio ..........................56 3-7 Motion .......................... 57 3-8 PTZ Control......................... 59 3-9 Event..........................61 3‐9‐1 Settings........................62 3‐9‐2 Media ........................64 3‐9‐3 Event Server ......................65 3-10 Recording to SD Card..................... 70 3-11 Log ..........................
Page 7
DG-SC7100P-10 User Manual 5‐1‐6 Security ........................104 5-2 Video Playback......................106 5‐2‐1 Start Video Playback ....................106 5‐2‐2 Advanced Search ..................... 108 5‐2‐3 Event Search......................112 5‐2‐4 Video Playback......................116 6. Appendix ..........................119 6-1 Specification ......................119 6-2 Troubleshooting......................120 6-3 Glossary ........................121 ...
1. Product Information 1-1 Product Introduction DG-SC7100P-10 is a Speed Dome IP camera with 10x Optical Zoom. The speed dome camera is designed in such a way making it an ideal solution for drop-ceiling mounting for indoor applications. With its 360 degree continuous Pan and 180 degree Tilt, the camera can monitor a larger area.
DG-SC7100P-10 User Manual 1-1 Safety Instructions In order to keep the safety of users and your properties, please follow the safety instructions as mentioned below. The warranty will become void if you disobey these safety instructions.
DG-SC7100P-10 User Manual 1-2 System Requirements Windows XP, Vista or Win 7 operating system (both 32 or 64 bits version) 2GB of system memory 1GB of Display card memory 20GB of available hard disk space on system drive ...
Before you start using this IP camera, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items: 1. DG-SC7100P-10 Speed Dome POE IP Camera (1 No.) 2. Switching Power Adapter (12V DC, 2A) 3.
DG-SC7100P-10 User Manual 1-4 Get Familiar with your new Network Dome Camera Rear View: Sr. No. Item Description Connect to your local area network by Ethernet cable. Ethernet Left LED: Power Indicator Right LED: LAN connectivity Digital input / output dry contacts.
DG-SC7100P-10 User Manual DI/DO PIN ASSIGNMENT Item Description 1. Relay Digital Output ground 2. Relay Digital Output1 3. DI Digital Input 1 4. GND Signal ground 5. RS-485+ RS-485 signal positive(+) 6. RS-485- RS-485 signal negative(-) ...
DG-SC7100P-10 User Manual 1-5 Installation of the Network IP Camera Please follow the below mentioned instructions to setup your new dome camera. To mount the IP camera on the wall or ceiling, please refer to next section.
Page 15
DG-SC7100P-10 User Manual 2. Connect IO signal cable to IO port located at the back of dome camera. You can skip this step if you don’t have external I/O devices to connect. ...
Page 16
DG-SC7100P-10 User Manual 3. Use a RCA cable (not supplied in accessory kit) to connect ‘Video Out’ port, and connect the other end of RCA cable to peripherals which support video input, like DVR, VTR, or television.
Page 17
DG-SC7100P-10 User Manual 4. Connect audio cable to “Audio in-out” port located at the back of dome camera, and connect the other end of audio cable to audio peripherals like amplifier or microphone. ...
Page 18
DG-SC7100P-10 User Manual 6. Insert the other end of AC adapter to “DC 12V” located at the back of dome camera. If everything is correct, you should see the LED light next to the Ethernet port lit up. If not, please recheck installation procedures listed above again.
DG-SC7100P-10 User Manual 1-6 Ceiling-mount / Wall-mount Installation 1. Use 3 screws (supplied with the package) to securely fix ceiling mounting bracket A on the wall or ceiling. NOTE: 1) Please refrain from mounting the camera on a thin wooden wall / ceiling to ...
Page 20
DG-SC7100P-10 User Manual If you want to fix the IP dome camera to ceiling / wall plate, kindly perform the below mentioned steps:- a. Take ceiling mounting bracket B and draw a circle by pen or pencil along the inner circle of mounting bracket B, then use appropriate tool to cut a hole on the wall / ceiling plate.
Page 21
DG-SC7100P-10 User Manual d. Fasten IP dome camera on the wall / ceiling with mounting bracket A, turn IP dome camera clockwise slowly and carefully. e. Pass the IP dome camera through wall/ ceiling plate and mounting bracket B, then pass mounting bracket C through IP dome camera.
Page 22
DG-SC7100P-10 User Manual g. Take IP dome camera and fasten it to the ceiling mounting bracket A by turning IP dome camera clockwise slowly and carefully. h. Connect Ethernet and other cables. ...
DG-SC7100P-10 User Manual 2. Using Network Dome Camera by Web Interface 2-1 Locate the IP address of Network IP Camera You can use your new Network IP Camera by its web user interface via web browser.
Page 24
DG-SC7100P-10 User Manual If you need to change a certain dome camera’s IP address, you can also click on the dome camera whose IP address you wish to change, then click ‘Change IP’ button to change select dome camera’s IP address setting.
DG-SC7100P-10 User Manual 2-2 Connect to dome camera’s Web User Interface When you know the IP address of dome camera, you can connect to it by Internet Explorer web browser by entering its IP address in the address bar. The user login screen will appear when you get connected: ...
Page 26
DG-SC7100P-10 User Manual For IE 8 version: Right click the indication bar and click: ‘‘Run Add-on” for All Users on This Computer to install ActiveX plugin. For IE9 version: ...
Page 27
DG-SC7100P-10 User Manual Click ‘Allow’ button located at the bottom of IE to install ActiveX plugin. If you’re prompted that Windows Firewall has blocked some features of this program as shown below. Click ‘Allow access’, or dome camera will not be able to function properly.
Page 28
DG-SC7100P-10 User Manual Click on ‘Continue’. It will display the screen shown below: Once you click on Run Active X Control, the following screen appears: Click on ‘Run’ to install the Active X. ...
Page 29
DG-SC7100P-10 User Manual After ActiveX plugin is installed, you should be able to see the video stream from camera. NOTE: If this is the first time you use this dome Camera, you can refer to chapter 2.4...
DG-SC7100P-10 User Manual 2-3 Viewing Live Video After ActiveX control is installed, you can view dome camera’s video by web browser. Just connect to dome camera by web browser and login, than you can see live video from dome camera: ...
Page 31
DG-SC7100P-10 User Manual Pan-Tilt Control This 8-direction (up / down / left / right, and upper- left/right, lower-left/right) button lets you control dome camera’s pan-tilt movement. Advanced Control Tab Click this tab and a new control tab will unfold:...
Page 32
DG-SC7100P-10 User Manual Available languages: English, Simplified Chinese, Traditional Chinese. Original size / Fit Switches live image view between original size (full size: screen D1) and fit screen (smaller size). If you want to see video in detail, switch to original size.
Page 33
DG-SC7100P-10 User Manual Note: Digital zoom uses computer algorithm to enlarge the video and some details may be lost. Enable / Disable mute When mute is enabled ( ), you will not hear the voice button from Dome camera;...
DG-SC7100P-10 User Manual 2-4 Client Settings In ‘Client Settings’ menu, you configure basic Dome camera settings like data transfer protocol and data storage folder. To access ‘Client Settings’ menu, click ‘Client Settings’ button on the left of the web page as shown below.
Page 35
DG-SC7100P-10 User Manual The following screen will appear: Here is the description of every setup item: Item Description RTSP Select this option to use RTSP (Real-Time Streaming Protocol) to transfer video data. HTTP Select this option to use HTTP (Hyper-Text Transfer Protocol) to transfer video data.
DG-SC7100P-10 User Manual 3. Advanced Configuration If you wish to configure IP camera’s settings, you can access IP camera’s ‘Configuration’ menu, which provides various kinds of system setting. To access configuration menu, click ‘Configuration’ button on the left of the webpage.
DG-SC7100P-10 User Manual 3-1 System In this menu, you can configure basic dome camera settings like hostname and time. Here is the description of every setup item: Item Description Host Name Input the IP camera’s hostname here, it can be any meaningful words or characters that will help you to identify this IP camera.
Page 39
DG-SC7100P-10 User Manual Keep the Select this option and date / time setting will not be changed current date when you click ‘Apply’ in the page. and time You can check ‘Camera Date and Time’ item in this page to know IP camera’s current date and time setting.
DG-SC7100P-10 User Manual 3-2 Security In this menu, you can configure IP camera’s login account. There are three kinds of accounts: - Administrator (Can view IP camera’s video and make changes of camera setting) - User (Can view IP camera’s video and see settings, but can’t make any change) - Guest (Can view IP camera’s video only)
Page 41
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Password/ Retype Input administrator’s new password in both ‘Password’ and Password ‘Retype Password’ field, and click ‘Modify’ button to change administrator’s password.
DG-SC7100P-10 User Manual 3-3 Network You can configure the network camera’s general and advanced network settings here. 3-3-1 General setup page Setup IP address for this IP camera. This IP camera supports both IPv4 and IPv6 IP . ...
Page 43
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Select this option to assign an IP address to LAN port (or obtain LAN an address from DHCP server automatically). Available options are: DHCP IPv4: Obtain an IPv4 IP address from DHCP server on LAN automatically.
Page 44
DG-SC7100P-10 User Manual operator to get connected. HTTP Port Input IP camera’s web connection port number here. When this port number is changed, you need to change web browser’s port number you used to connect to IP camera.
DG-SC7100P-10 User Manual 3-3-2 Advanced setup page You can setup advanced network settings in this page. This page is intended for advanced settings only, and this IP camera will work fine even if you don’t make any changes to this page.
Page 46
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Multicast Enable video multicast: Multicast Group Address: Input multicast group address here, must be an address between 232.0.0.0 to 232.255.255.255. Multicast video port: Input port number for video multicast here.
DG-SC7100P-10 User Manual User name: Input user name used to login dynamic IP service provider. Password: Input the password used to login dynamic IP service provider. HTTPS Check ‘Enable HTTPS’ box to enable HTTPS channel to encrypt transferred data.
Page 48
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Enable Filter Check this box to enable IP address filter, uncheck this box to disable this function. Accepted IP Here lists all IP addresses that can build connections to this IP list camera.
DG-SC7100P-10 User Manual 3-5 Video You can adjust the image of the Dome camera in this menu. There are 3 sub-menus in this menu: Image Setting, Video Setting, and Overlay which can be accessed by tabs on the top: ...
DG-SC7100P-10 User Manual 3-5-1 Image Setting You can adjust the image parameters in this page. Here is the description of every setup item: Item Description Brightness / Control the image parameters. Click ‘-’ to decrease value, or click ‘+’...
DG-SC7100P-10 User Manual or horizontally, this will help to correct the orientation of image when Dome camera is hanged bottom-up by camera holder. You can click both ‘Vertical’ and ‘Horizontal’ box at the same time.
Page 52
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description H.264 / Select the compression of main stream: H.264 / MPEG4 MPEG4 Video Select video resolution. Resolution H.264: 720x480 (D1) / 640x480 (VGA)
DG-SC7100P-10 User Manual Bitrate: Input video’s bit rate directly. It must be an integer between 512 and 4000. Higher bit rate provides better video quality, but consumes more network bandwidth. When you finish with above settings, click ‘Apply’ button to save changes.
DG-SC7100P-10 User Manual 3-5-3 Overlay Setting You can adjust the video overlay parameters in this page. Here is the description of every setup item: Item Description Enable Time Check this box to enable overlaying time stamp on video.
Page 55
DG-SC7100P-10 User Manual background help the readability of text in some cases. color of the text (Text) Enable Image Check this box to overlay a specific image on video, so you can Overlay show certain text / picture on the video and help people to identify this IP camera.
DG-SC7100P-10 User Manual 3-6 Audio You can adjust audio input / output parameters here. Here is the description of every setup item: Item Description Enable Check this box to enable microphone. If you don’t want to hear Microphone voice from IP camera, you can un-check this box to disable it.
DG-SC7100P-10 User Manual 3-7 Motion This Dome camera is capable to detect object’s motion, so dome camera will only record when there’s motion and save disk storage space. Motion detection is performed by examining the movement of objects in rectangular motion detection area.
Page 58
DG-SC7100P-10 User Manual - Move: Use the mouse to drag the title text. - Resize: Use the mouse to drag the four corners (upper- left/right, lower-left/right) to resize it. If you only want to adjust width or height, drag the four sidebars (top, bottom, left, and right).
DG-SC7100P-10 User Manual 3-8 PTZ Control If you mount the Dome camera on pan-tilt camera cradles that support pan-tilt control via RS-485 connection, you can use this function to control pan-tilt camera cradle so you can control the orientation of dome camera from remote place.
Page 60
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Enable RS-485 Check this box to enable RS-485 functionality. Use Pelco-D Select this option and RS-485 interface will output pan-tilt control signal in Pelco-D format. This format is widely accepted by most of pan-tilt camera cradles.
DG-SC7100P-10 User Manual 3-9 Event When there’s an event, you can use this setup page to define what IP camera should do, like send an Email or trigger digital output to activate external alarm.
DG-SC7100P-10 User Manual 3-9-1 Settings This page lists all existing events. You can click ‘Modify’ button to edit an existing event, or ‘Remove’ to delete an existing event. To create a new event, just click “New” button to add an Event setting.
Page 63
DG-SC7100P-10 User Manual To add a new event, click ‘New’ button and the description of every setup item is listed below: Item Description Enable Setting Check this box to enable this event. If you just want to disable this event temporarily, you can uncheck this box to disable the event without deleting it.
DG-SC7100P-10 User Manual 3-9-2 Media You can define what kind of media file should be saved to designated path. Here is the description of every setup item: Item Description One Snapshot Save a picture file when event is triggered.
DG-SC7100P-10 User Manual 3-9-3 Event Server You can define the details of remote media server: FTP (File), SMTP (Email), and Samba (File). A Samba server can be any computer running windows operating system with network neighbor function enabled.
Page 66
DG-SC7100P-10 User Manual Here is the description of every setup item: Item Description Enable FTP Check this box to enable FTP server upload. Server - FTP Server: Input FTP server’s IP address or hostname.
Page 67
DG-SC7100P-10 User Manual - SMTP Server: Input SMTP server’s IP address or hostname. - Port: Input SMTP server’s port number. In most cases it should be default value ‘25’. - Sender Email Address: Input the sender’s email address that will appear in the Email send by dome camera.
Page 68
DG-SC7100P-10 User Manual input Email server’s username and password in corresponding field. - Requires SSL Encryption: If your Email server required SSL encryption, check this box. Please note that some Email server uses different port number than standard port 25 when SSL encryption is used.
Page 69
DG-SC7100P-10 User Manual - Password: Input Samba server’s password. - Test SMB: Click this button to test Samba server settings above immediately. Tips: Some samba server does not have username and password check, you can just input samba server address and path to access the file storage space.
DG-SC7100P-10 User Manual 3-10 Recording to SD Card When a SD card is inserted into dome camera, you can save video files on it. Note: 1. Be sure that the SD Card format should be FAT32. The NTFS format cannot be supported by this camera.
DG-SC7100P-10 User Manual 3-11 Log You can check the usage log of dome camera here. In this page, you can click: 1. First page / Final page: Jump to first / final page of log.
DG-SC7100P-10 User Manual 3-12 Device Info You can check the information and network settings of this dome camera. These information are very useful when you need to repair or fix the problem of this dome camera.
DG-SC7100P-10 User Manual 3-13 Maintenance You can do some maintenance job about this dome camera here. Here is the description of every setup item: Item Description Reboot Click this button to reboot the dome camera. This function is useful when you find that the dome camera is not working properly.
DG-SC7100P-10 User Manual first, then click ‘Restore’ button. Restore from Restore dome camera’s configuration which is previously-saved on SD card device SD card. Upgrade Upgrade dome camera’s firmware. Click ‘Browse’ button to select a firmware image file on your computer first, then click ‘Upgrade’...
DG-SC7100P-10 User Manual 4. Using SKYROS iView software 4-1 Installing SKYROS iView Software The SKYROS iView software provides various functions like video recording. After this software is installed, you can use your IP camera to safeguard your property. Please follow the below mentioned instructions to install the SKYROS iView software.
Page 76
DG-SC7100P-10 User Manual 2. Double click on ‘Setup.exe’ to install the ‘SKYROS iView’ software. The wizard as shown below will appear. 3. The screen as shown below will appear. Click ‘Next’ to continue. ...
Page 77
DG-SC7100P-10 User Manual 4. Now, click on ‘Install’ as shown below. 5. Please wait while installation is being performed. This may take few minutes, please be patient. 77 ...
Page 78
DG-SC7100P-10 User Manual 6. Second part of installation will start automatically. 7. A new setup window will appear, please click ‘Next’ button to continue. 78 ...
Page 79
DG-SC7100P-10 User Manual 8. Now, click on ‘Next’ as shown below. 9. The screen shown below will appear. Click on ‘Install’ as shown below. 79 ...
Page 80
DG-SC7100P-10 User Manual 10. Installation will take few minutes, please be patient. 11. Click ‘Finish’ when you see this message. 80 ...
Page 81
DG-SC7100P-10 User Manual 12. MSDE (Microsoft SQL Database Engine) installation procedure will start at the same time. Please wait until it completes. 81 ...
Page 82
DG-SC7100P-10 User Manual 13. Following screen will appear. Click on ‘Finish’. A new icon will appear on your computer’s desktop, you can double click on it to start SKYROS iView ...
DG-SC7100P-10 User Manual 5 Getting familiar with SKYROS iView Software To start SKYROS iView, double click SKYROS iView icon on your computer’s desktop: Or click ‘Start’ button of Windows, and select ‘All Programs’ -> ‘SKYROS iView- >Launch SKYROS iView’...
Page 84
DG-SC7100P-10 User Manual SKYROS iView login screen will appear as shown below. Default user ID is ‘admin’ and default password is none (leave it blank), click ‘OK’. The main window of SKYROS iView will appear: EXIT ...
Page 85
DG-SC7100P-10 User Manual The description of every item is listed below: Item Description Split-screen mode SKYROS iView supports from 1 to 64 cameras split views. The video from IP camera will display in split screen display selector cells, and you can view up to 64 IP cameras at the same time.
Page 86
DG-SC7100P-10 User Manual Select the file, and click ‘Open’ button to use the picture as background picture. To add a camera, right click on the background picture and select ‘Add Camera…’ A new window will appear: Select the camera you wish to add from ‘Camera’...
Page 87
DG-SC7100P-10 User Manual You can add more cameras to EMAP by repeating procedures listed above. Configuration Enter SKYROS iView configuration page. See next section for detailed instructions. Playback Playback recorded video. A new video playback window will appear.
Page 88
DG-SC7100P-10 User Manual All camera’s video will be displayed in ‘Camera View’ area: (This example picture shows a camera view with only 1 IP camera configured) To select an IP camera, click its video and it will be highlighted; some IP cameras support additional control, and a control panel will appear at the bottom right area of SKYROS iView.
DG-SC7100P-10 User Manual Zoom Optical zoom control. Click + or - to control zoom level. This function is only available for supported cameras. Auto Focus Click + or – to adjust the focus. This function is only available for supported cameras. ...
DG-SC7100P-10 User Manual The configuration menu will appear. There are 6 sub menus in the configuration menu: Device (Add or remove IP camera / video server) Recording (Configure video recording) System (Configure system wide settings) ...
Page 91
DG-SC7100P-10 User Manual If your IP camera is located on local area network, click ‘Search’ button. Wait for few seconds or few minutes until the search is complete, and all IP cameras found on your local area network will be listed: ...
Page 92
DG-SC7100P-10 User Manual When an IP camera is found, you can also select it in the list and: View Image: View the live image from selected IP camera. Detail: Connect to selected IP camera’s web configuration menu.
DG-SC7100P-10 User Manual You can also manage IP camera list by the following function: Enable All: Enable all IP cameras in the list. Disable All: Disable all IP cameras in the list. Remove: Remove selected IP camera.
Page 94
DG-SC7100P-10 User Manual The description of every item is listed as follows: Item Description Select Camera Please select an IP camera from the list to setup its recording behavior. SKYROS iView will attempt to connect to selected IP camera, if it’s not connectable, you will receive an error...
Page 95
DG-SC7100P-10 User Manual To add or erase blocks: To add blocks, click + button; to erase blocks, click - button. Click ‘Reset’ button to reset motion detection blocks to default setting. You can also change the color of block if the color is similar to the IP camera’s video and its difficult for you to...
DG-SC7100P-10 User Manual 5-1-3 System You can configure system-wide configuration in this sub menu. The description of every setup item is listed below: Item Description Host Name The host name by default is ‘SKYROS iView’.
Page 97
DG-SC7100P-10 User Manual file automatically. If you didn’t check this box, SKYROS iView will stop recording when data storage space is full. Alarm Space: When data storage space is less than the size you specified here, you’ll receive an alarm message to notify that you should do something to prevent running out of storage space.
Page 98
DG-SC7100P-10 User Manual Auto Login Input the user ID and password to login SKYROS iView automatically. This function is useful when you want to start recording automatically when computer starts. User ID: Input user ID used to login SKYROS iView, must have adequate privileges to perform the action you wish to execute.
DG-SC7100P-10 User Manual authentication. Camera Scan Interval Input the time interval to wait between camera scan. Connection Retry Decides the behavior when SKYROS iView lost communication with IP camera: Retry: Retry for the time you specified here.
Page 100
DG-SC7100P-10 User Manual A new window will appear on the right: You can configure a new schedule recording job here. The description of every setup item is listed below: Item Description Weekly Schedule Select the time period in a week of this schedule. There are total 48 x 7 blocks in a week schedule, where every block represents half an hour.
Page 101
DG-SC7100P-10 User Manual To add or delete a time period, select ‘ADD’ or ‘DEL’ first, then click the time period block. In order to start the schedule recordings click the schedule button on the main screen of the software.
DG-SC7100P-10 User Manual 5-1-5 Event SKYROS iView can send you an alarm email message so you can know something happened on the IP camera (motion detected, video lost, or connection lost). A sound can be played to notify the operator at the computer where SKYROS iView is installed, too.
Page 103
DG-SC7100P-10 User Manual Motion detected: Alarm will be triggered when motion is detected at this IP camera. Video lost: Alarm will be triggered when video server’s external camera signal is lost. Connection Lost: Alarm will be triggered when network connection to this IP camera is lost.
DG-SC7100P-10 User Manual 5-1-6 Security You can add or remove users which are allowed to access SKYROS iView. There are two kinds of users in SKYROS iView: Administrator and user.
DG-SC7100P-10 User Manual To add a user, click ‘Add’ button, a new window will appear on the right: The description of every setup item is listed below: Item Description User ID Input the user ID used to login SKYROS iView...
DG-SC7100P-10 User Manual Scheduling: User can start or stop schedule recording. Recording: User can start or stop video recording. Playback: User can playback saved video. Camera List Select IP cameras you wish to allow this user to view.
Page 107
DG-SC7100P-10 User Manual A new window will appear: To play a recorded video, you can use one of following two functions: Advanced Search Event Search Please refer to following chapters for detailed instructions of every search mode.
DG-SC7100P-10 User Manual 5-2-2 Advanced Search You can search for recorded video within specific time period, and get a list of record modes of all IP cameras. ...
Page 109
DG-SC7100P-10 User Manual When you finish, click ‘SEARCH’ button to search for recorded video, and you will get a similar output like this: In this picture, a recorded video of ‘Camera 1’ has been found at 12 o’clock. A blue mark indicates it’s a ‘Round Clock’...
Page 110
DG-SC7100P-10 User Manual To view the video, check the box of camera ID, then click ‘Play’ button. And the video will be prepared for playback. 110 ...
Page 111
DG-SC7100P-10 User Manual Recorded Video Clip For instructions of video playback, please see section 5-2-4 for detailed instructions. 111 ...
DG-SC7100P-10 User Manual 5-2-3 Event Search You can search for video for playback by triggering event: round the clock, motion detection, or digital input. 112 ...
Page 113
DG-SC7100P-10 User Manual To search for video, you have to specify: 1) Starting and Ending time for video searching in ‘Start time’ and ‘Stop time’ field. HOUR IN A DAY DATE 2) Recording mode: Round Clock, Motion Detection, and I/O Mode (Digital Input).
Page 114
DG-SC7100P-10 User Manual When you finish, click ‘Search’ button to search for recorded video, and a list similar to this will appear: RECORDED VIDEO FILES You can select the video clip you wish to play, and click ‘Play’ button.
Page 115
DG-SC7100P-10 User Manual For instructions of video playback, please see section 5-2-4 for detailed instructions. 115 ...
DG-SC7100P-10 User Manual 5-2-4 Video Playback When a video is loaded, the video playback screen will look like this: The description of every item is listed as below: Item Description Close Window Click X mark to close video playback window.
DG-SC7100P-10 User Manual Skip to next video frame Pause a playing video, click the same button to resume video playback Stop video playback Skip to previous video frame Skip to the beginning position of video Speed Control When video is stopped, you can click + or –...
Page 118
DG-SC7100P-10 User Manual You can adjust image brightness / contrast by dragging corresponding slide bar, or click ‘Gray Scale’, ‘Sharpness’, ‘Soften’ to adjust image parameters. You can click ‘Save as’ button to save current image (you’ll be prompted for image saving location), or click ‘Print’...
DG-SC7100P-10 User Manual 6-2 Troubleshooting Please don’t panic when you found this dome camera is not working properly. Before you send this dome camera back to us, you can do some simple checks to save your...
DG-SC7100P-10 User Manual 6-3 Glossary MJPG : Motion JPEG or M-JPEG is a digital video sequence that is made up of a series of individual JPEG images. (JPEG stands for Joint Photographic Experts Group). The quality of the image is guaranteed, regardless of movement because the captured video is a series of separately compressed JPEG images that can be extracted individually.
Page 122
DG-SC7100P-10 User Manual SMTP (Simple Mail Transfer Protocol): SMTP is used for sending and receiving e-mail. SMTP authentication is an extension of SMTP, whereby the client is required to log into the mail server before or during the sending of email. It can be used to allow legitimate users to send email while denying the service to unauthorized users, such as spammers.
Page 123
IR Ray from the image and offers a true color image. During night operations the IR cut filter is removed automatically and provides a monochrome image. This product comes with One Year warranty. For further details about warranty policy and Product Registration, please visit support section of www.digisol.com ...