TABLE OF CONTENTS Operator’s manual for FR 2111, FR 2113 A, FR 2113 MA, FR 2116 MA Introduction ............2 Replacing the fuel filter ........26 Driving and transport on public roads ....2 Replacing the air filter ........27 Towing ..............
INTRODUCTION Congratulations Thank you for purchasing a Front Rider. Front Riders have been designed according to a unique concept with a front mounted mowing deck and patented rear wheel steering. The machine is built to give maximum efficiency even in small and confined areas. Collected controls and a hydrostatic transmission controlled by pedals(some models) also contribute to the machine’s performance.
INTRODUCTION Good service Jonsered’s products are sold all over the world and only in specialised retail trade with complete service. This ensures that you as a customer receive only the best support and service. Before the machine is delivered it undergoes inspection and is adjusted by your dealer. When you need spare parts or support in questions about service, warranty issues, etc., please consult the following professional: Engine...
EXPLANATION OF SYMBOLS These symbols can be found on the Rider and in the operator’s manual. Study them carefully so you understand their significance. Read the operator’s manual. Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil level Cutting height Reversing Forward Ignition...
SAFETY INSTRUCTIONS Safety instructions These instructions are for your safety. Read them carefully. WARNING! The inserted symbol means that important safety instructions need to be observed. It applies to your safety. General use • Read all the instructions in this operator’s manual and on the machine before you start it.
Page 8
SAFETY INSTRUCTIONS • Take care when rounding a fixed object, so that WARNING! the blades do not hit it. Never run the machine Engine exhaust, some of its over foreign objects. constituents and certain vehicle components contain or emit • Only use the machine in daylight or in other chemicals considered to cause well-lit conditions.
SAFETY INSTRUCTIONS Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest; this can result in serious injury or death. All slopes demand extra care.
SAFETY INSTRUCTIONS Children • Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing. Never assume that children will remain where you last saw them. •...
Page 11
SAFETY INSTRUCTIONS • If leaks arise in the fuel system, the engine must not be started until the problem has been resolved. WARNING! • Store the machine and fuel in such a way that The engine, and components of there is no risk that leaking fuel or fumes can the exhaust and hydraulic cause any damage.
SAFETY INSTRUCTIONS • Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas. • Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.
FR 2113 is available in two versions. FR 2113 A has Stratton are described in this operator’s manual. a mowing deck with rear ejection and FR 2113 MA has a mowing deck with mulching. FR 2111 has an inline type gearbox with 5 forward gears and reverse. 8009-243 8009-244...
PRESENTATION FR 2111 Throttle and Choke controls The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold.
PRESENTATION FR 2113, FR 2116 Throttle and Choke controls The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold.
PRESENTATION Mowing deck FR 2111 and FR 2113 A have a triple blade mowing deck with rear ejection, i.e. the clippings are thrown out behind the mowing deck. 8009-260 FR 2113 MA has a double blade mulching unit and FR 2116 MA has a triple blade Combi unit, which can be set to either a mulching function or rear ejection by removing a mulching plug.
PRESENTATION Lever to adjust the cutting height Using the lever the cutting height can be adjusted in 9 different positions. Deck with rear ejection, 40-90 mm (1 9/16" - 3 9/16") Mulching and combi unit, 45-95 mm (1 3/4" - 3 3/4") 8009-251 Seat The seat has a hinged mounting on the front edge...
The parking brake’s lock is automatically disengaged when the brake pedal is pressed down. The FR 2111 has the brake pedal and lock button on the right-hand side. 6007-002H 3. On FR 2111 Put the gear shift lever in the N position (neutral).
Page 19
DRIVING With a cold engine: 4. Move the throttle to position 3 (choke position). In this position the engine is fed with a richer mixture, which means the engine is easier to start. The throttle must be moved to the side (towards the ignition key) to reach the choke position.
Pedal (1) is pressed down to travel forwards and pedal (2) to reverse. 6007-010H On FR 2111 Disengage the engine and select the required gear. The lock button must be held in to engage reverse gear.
DRIVING 3. Select the required cutting height (1-9) using the cutting height lever. In order to obtain an equal cutting height, it is important that the air pressure is the same in both front wheels (60 kPa/8.5 PSI). 8009-251 4. Press in the lock button on the lifting lever and lower the mowing deck.
1. Lift up the mowing deck by pulling the lever backwards to its end position. 8009-249 2. FR 2111: Pull back the throttle and move the gear shift lever to the neutral position N, without pressing in the reversing lock button.
Check the mowing deck Check the air pressure in the tyres (60 kPa/8.5 PSI) Lubricate the belt adjuster Lubricate joints and shafts Adjust the brakes FR 2111 Check the V-belts – Check the transmission’s cooling fins on FR 2113, 2116 –...
Fold the seat forward, loosen the rubber strap under seat and fold the cover backwards. 8009-262 Front cover FR 2111, FR 2113 A Remove the bolts holding the front cover (3) and lift off the cover. 8009-263 Front cover FR 2113 MA, FR 2116 MA Loosen the snap-in lock and lift off the cover.
Page 25
MAINTENANCE Right-hand wing cover Remove the bolts holding the wing cover (2 and 3). On FR 2113 and FR 2116 the knob (1) should also be removed. 8009-265 Left-hand wing cover Remove the bolts holding the wing cover and lift off the cover.
MAINTENANCE Checking and adjusting the steering wires The steering is governed by means of wires. After a period of use these can become stretched, which means the steering setting may have changed. The steering is checked and adjusted as follows: 1.
MAINTENANCE Checking the brake FR 2111 The brake is a disc brake and is located on the gearbox. Check that the brake is adjusted correctly by measuring the distance between the brake lever and front edge of the cut-out on the chassis.
MAINTENANCE Adjusting the throttle cable The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached. 1. Loosen the clamping screw (by the arrow), and slide the throttle to the choke position.
MAINTENANCE Replacing the air filter If the engine seems to lack power or goes irregu- larly the reason may be that the air filter is clogged. It is therefore important to replace the air filter at regular intervals (see ”Maintenance schedule” for correct service interval).
MAINTENANCE Checking the fuel pump’s air filter Check regularly that the fuel pump’s air filter is not clogged by dirt. The filter can be cleaned using a brush, if neces- sary. Checking the acid level in the battery Check that the acid level in the battery lies between the markings.
MAINTENANCE FR 2111 Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the mowing deck is in its raised position and the...
MAINTENANCE FR 2113, FR 2116 Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the mowing deck is in its raised position and the Starter Works gear shift lever or hydrostat pedals are in the...
8009-268 Checking the engine’s cooling air intake FR 2111, FR 2113, FR 2116 Clean the air intake grille in the engine cover behind the driver’s seat. Fold up the engine cover.
MAINTENANCE Checking and adjusting the mowing deck’s ground pressure on FR 2113 MA and FR 2116 MA In order to achieve the best mowing result the mowing deck should follow the ground without touching it too heavily. The pressure is adjusted using a screw on each side of the Rider.
MAINTENANCE FR 2111, FR 2113 MA Adjusting the parallelism of the mowing deck on FR 2111 1. Check that the tyres’ air pressure is 60 kPa (0.6 kp/cm /8.5 PSI). 2. Dismantle the front cover and the right-hand wing cover as described on pages 22-23.
MAINTENANCE FR 2116 MA Adjusting the parallelism of the mowing deck on FR 2116 MA 1. Check that the tyres’ air pressure is 60 kPa (0.6 kp/cm /8.5 PSI). 2. Remove the front cover and the right-hand wing cover. 3. Loosen the parallelism stay’s nuts. 4.
MAINTENANCE FR 2113 MA, FR 2116 MA The mowing deck’s service position In order to provide good accessibility for cleaning, repair and servicing, the mowing deck can be set in the service position. The service position means that the mowing deck is raised and locked in the vertical position.
Page 38
MAINTENANCE FR 2113 MA, FR 2116 MA 4. Fit the two support wheels on each side of the mowing deck’s rear section. WARNING! Wear protective glasses when dismantling the mowing deck. The spring that tension the belt can fly off and cause personal injury.
Page 39
MAINTENANCE FR 2113 MA, FR 2116 MA WARNING! Exercise care so that your hands are not crushed. 8. Lift off the drive belt (1). Now pull out the split pin (2). 6017-225 9. Pull the frame forwards and refit the pin. 6017-226 10.
MAINTENANCE Inspecting the blades It is important that the blades are undamaged and well-ground to give the best mowing result. Check that the blades’ mounting bolts are tightened. IMPORTANT INFORMATION Replacement or sharpening of the blades should be carried out by an authorised service workshop.
LUBRICATION Check the engine’s oil level Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Fold open the engine cover. Release the dip stick and pull out. Wipe off the oil and insert again. The dip stick must be fully screwed down.
LUBRICATION Checking the oil level in the transmission on FR 2113, FR 2116 1. Remove the transmission cover. Loosen both screws (one on each side) and lift off the transmission cover. 8009-273 2. Check that there is oil in the transmission’s oil tank.
LUBRICATION Lubricating the front wheel bearings The front cover and wing covers must be removed on machines with rear ejection, so that the tubular loop can be lifted to remove the wheel. 1. Remove the plastic cover that covers the centre of the wheel.
TROUBLE SHOOTING CHART Problem Cause The engine will not start • No fuel in the fuel tank • Faulty spark plug • Fault spark plug connection • Dirt in the carburettor or fuel line Starter does not turn the engine •...
STORAGE To ready the Rider for storage, follow these steps: Winter storage 1. Clean the Rider carefully, especially under the At the end of the mowing season the Rider should mowing deck. Touch up damage to the paint to be readied for storage, likewise if it will not be in prevent rust.
TECHNICAL DATA Dimensions FR 2111 FR 2113 A Length with mowing deck 2040 mm/6.6 ft 2040 mm/6.6 ft Width 880 mm/2.89 ft 880 mm/2.89 ft Height 1070 mm/3.52 ft 1070 mm/3.52 ft Weight with mowing deck 216 kg/475 lbs 219 kg/481 lbs Distance between axles 860 mm/2.81 ft...
Page 47
TECHNICAL DATA Dimensions FR 2113 MA FR 2116 MA Length without mowing deck 2010 mm/6.58 ft 2010 mm/6.58 ft Length with mowing deck 2220 mm/7.29 ft 2220 mm/7.29 ft Width without mowing deck 880 mm/2.89 ft 880 mm/2.89 ft Width with mowing deck 1000 mm/3.29 ft Height 1070 mm/3.52 ft...
Page 48
TECHNICAL DATA Mowing deck Type Triple blade cover Double blade cover Triple blade cover with rear ejection Mulching 900 mm Combi 1030 mm Mowing width 850 mm/33.5" 900 mm/35.5" 1030 mm/40.5" Cutting heights 9 positions 40-90 mm/1 9/16" - 3 9/16" 45-95 mm/1 3/4"...
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the Rider Jonsered FR 2111, FR 2113 A, FR 2113 MA, FR 2116 MA, from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVES:...
6. Check and adjust the air pressure in the tyres (60 kPa/0.6 bar/8.5 PSI). 7. Connect the battery. 8. Fill the fuel tank and start the engine. 9. Check that the machine does not move in neutral (not FR 2111). 10. Check: Driving forwards.