Contents TV - Features ............2 Connecting to your mobile device via WiFi ..19 Using MIRACAST ..........19 Dear SHARP customer ........... 3 Using DLNA Network Service ......20 Important safety precautions ........3 Internet Portal ............20 Environmental Information ........6 Netflix..............
LC-50LE762E / LC-50LE762EN / LC-50LE759EN pin face of the plug, must be used. HD DVB-T/CABLE(MPEG4) : Always refit the fuse cover after replacing the fuse. LC-42LE760E / LC-42LE756EN / LC-50LE760E / Never use the plug without the fuse cover fitted. LC-50LE756EN HD DVB-T2/CABLE(MPEG4) :...
• DLNA (DMP, DMR) Dear SHARP customer • HBBTV (This feature is not available for UK models) Thank you for your purchase of the SHARP LCD • Miracast. colour TV product. To ensure safety and many years The illustrations and the OSD in this operation manual...
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover WARNING or block these vents and openings since insufficient To prevent the spread of fire, keep ventilation can cause overheating and/or shorten candles or other open flames away the life of the product.
• If the cabinet is very dirty, wipe with a soft cloth • Do not try to recharge batteries, there is a danger (cotton, flannel, etc.) soaked in neutral detergent of explosion. Replace batteries only with the same diluted with water and thoroughly wrung out, and or equivalent type.
Environmental Information This television is designed to consume less energy to help save the environment. To reduce energy consumption, you should take the following steps: You can use Power Save Mode setting, located in the Picture menu. If you set Power Save Mode as Eco, the TV will switch to energy-saving mode and luminance level of TV set will be decreased to optimum level.
Package Contents Connect Power IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz socket. After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the mains. Plug the power cable to the mains socket outlet.
• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the unit. • The remote control unit may not work properly if the remote control sensor of the TV is under direct sunlight or strong lighting.
Viewing remote control - TV 1. Standby / On 2. Channel list 3. Volume up / down 4. Menu on/off 5. OK / Confirm 6. Return / Back 7. Internet Portal 8. My button 1 / YouTube (*) 9. a) (RC4847) My button 2 (**) b) (RC4848) Press this button to launch the Netflix application.
Viewing the Connections Note: When connecting a Connector Type Cables Device device via the YPbPr or Side AV input, you must use connection Scart cables to enable connection. Connection For Side AV input you should (back) use the supplied cable. the illustrations on the left side.
Standby Notifications Using a Conditional Access Module If the TV does not receive any input signal (e.g. from IMPORTANT: Insert or remove the CI module only when an aerial or HDMI source) for 5 minutes, the TV will go the TV is SWITCHED OFF. into standby.
Unicable: If you have multiple receivers and a First Time Installation unicable system, select this antenna type. Press OK to When turned on for the first time, the language continue. Configure settings by following instructions selection screen is displayed. Select the desired on the screen.
You can set your Media Browser preferences by using other cables between the TV and the audio system the settings menu. (A/V receiver or speaker system). When ARC is active, TV does not mute its other audio Changing Image Size: Picture Formats outputs automatically.
Menu Features and Functions Picture Menu Contents Press to view 3D settings. 3D Settings You can change the picture mode to suit your preference or requirements. The Picture mode can Mode be set to one of these options: Cinema, Game, Sports, Dynamic and Natural. Contrast Sets the lightness and darkness values of the screen.
Menu Features and Functions Sound Menu Contents Volume Adjusts the volume level. Selects the equalizer mode. Custom settings can be made only when in User Equalizer mode. Balance This setting is used for emphasizing left or right speaker balance. Headphone Sets headphone volume.
Menu Features and Functions This option is used to select which subtitle mode will be on the screen (DVB Subtitle Mode subtitle / TXT subtitle) if both is available. Default value is DVB subtitle. Available only in Norway. Hard of Hearing Enables any special feature sent from the broadcaster.
Teletext Electronic Programme Guide (EPG) Some, but not all channels send information about “ ” Teletext / Mix: Activates video text mode when the current and next programmes. Press the pressed once (if available in your broadcast). Press again to view analogue teletext page. Press again to “...
The files of the recorded programmes will not be Instant Recording available to be played on a computer. You can play Press (RECORD) button to start recording an the recordings only via your TV. event instantly while watching a programme. You can Lip Sync delay may occur during the timeshifting.
change the settings such as IP Address using this You can press YELLOW button to scan available menu. networks for wireless connection. Afterwards, a list of networks will be displayed. Select your network from the list and press OK. Broadband ISP If the selected network is protected with a password, connection key in the correct code.
Highlight Media Renderer and set as Enabled. DISCLAIMERS Connect to a Wired or Wireless Network • SHARP corporation bears no responsibility regarding the content and quality of the content provided by the content See the previous chapters for detailed information.
below. The user then can switch to other applications HBBTV System by using the links provided. The applications should HbbTV (Hybrid Broadcast Broadband TV) is a provide a way to terminate themselves, usually button standard that seamlessly combines TV services 0 is used for this.
Try searching for wireless networks again, using the Using the 3D Mode Network Settings menu screen. This product supports the viewing of 3D content from • The transmission speed differs depending on the devices such as a High Definition Satellite Receiver distance and number of obstructions between the or Blu-ray Player via HDMI, PC,YPBPR, USB inputs transmission products, the confi guration of these...
• Do not apply spray cleaners directly onto the surface • You can enjoy viewing 3D images on your TV by of the 3D Glasses.This may result in discoloration wearing the supplied 3D Glasses. Note that this TV’s and cracks and may cause the screen display to 3D feature works only with its specific 3D glasses.
3D Viewing Information - continued 3D Depth Sense (optional) This setting enables the control of 3D depth. HDMI 3D Viewing Information Refer to the size / distance guidelines below to 1080p@24 FP Supported Not Supported Not Supported experience 3D in the best possible way. 720p@50 FP Supported Not Supported...
6. The picture quality may degrade when two devices Software Upgrade are connected to the TV at the same time. In such a Your TV is capable of finding and updating automatically case, disconnect one of the devices. via the Aerial/Cable/Satellite(depends on the model) No picture signal or over the Internet.
off. You should then switch on the TV to enable recording feature. Otherwise, recording feature will not be available. If you cannot perform recording, try switching off the TV and then re-inserting the USB device while the TV is switched off. USB Is too Slow If “USB is too slow”...
PC Typical Display Modes AV and HDMI Signal Compatibility (Input Signal Types) The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions. Source Supported Signals Available Index Resolution Frequency 640x350 85Hz NTSC 60...
Supported File Formats for by MKV External Embedded subtitle MicroDVD MPEG-4 Timed Text MPSub Ogg Kate Ogg Writ SAMI SubRip (Advanced) SubStation Alpha SubViewer (only support 1.0 and 2.0) Universal Subtitle Format VobSub XSUB Supported DVI Resolutions When connecting devices to your TV’s connectors by using DVI converter cable(DVI to HDMI cable - not supplied), you can refer to the following resolution information.
NEGLIGENCE, BREACH OF WARRANTY, STRICT provider. SHARP shall not be liable to you or any third LIABILITY OR OTHERWISE AND WHETHER OR party for your failure to abide by such authorization or NOT SHARP AND/OR ITS AFFILIATES HAVE terms of use.
Nero MediaHome Installation To install Nero MediaHome, please proceed as follows: Note: To use DLNA function, this software should be installed to your PC. 1. Enter the link below completely in the adress-bar of your web browser. http://www.nero.com/mediahome-tv 2. Click the Download button on the opening page. The installation file will be downloaded onto your 3.
• Place the Stand (3) on the stand mounting pattern on the rear side of the TV. • Ensure the Stand (3) is placed correctly and that you can see the screw holes on the back of the Sharp Television.
Uninstalling the Stand IMPORTANT Please read the following information carefully before detaching the stand of your Sharp Television. Uninstalling the Stand • Before detaching the stand, ensure that the TV is unplugged from its power source. • Place the Sharp Television on a soft, stable and flat surface, facing down.
Screw Dimensions Wall Mounting Screw length = A+B Screw Cabinet Wall mount angle TO THE PRODUCT MODEL VESA MIN. / MAX. SCREW LENGTH (A LENGTH) LC-42LE760E LC-42LE761E LC-42LE761EN 200 x 200 (W X H) M6 x 8 / M6 x 12 LC-42LE761K LC-42LE762E LC-42LE762EN...