Display Indication; Setup Menu; Basic Operations - Pioneer MVH-159UI Owner's Manual

Operating this unit

Display indication

2 5 7 9
1 3 4 6 8
a b
Indicator State
The list function is being oper-
1
(list)
ated.
(iPod This unit's iPod function is op-
2
control) erated from your iPod.
Sub infor-
3
mation sec- Sub information is displayed.
tion
TA (traffic
4 announce- TA function is on.
ments)
TP (traffic
program
5
A TP station is tuned in.
identifica-
tion)
The sound retriever function
6
(sound re-
is on.
triever)
7 LOC
Local seek tuning is on.
8 (repeat) Track or folder repeat is on.
Random play is on.
(ran-
The iPod source is selected
9
dom/shuf-
and the shuffle or shuffle all
fle)
function is on.
Indicator State
! Tuner: band and fre-
quency
! RDS: program service
Main infor-
name, PTY information
a mation sec-
and other literal informa-
tion
tion
! USB storage device and
iPod: elapsed playback
time and text information
Appears when a lower tier of
b
folder or menu exists.
Set up menu
When you turn the ignition switch to ON after in-
stallation, set up menu appears on the display.
You can set up the menu options below.
1 After installation of this unit, turn the
ignition switch to ON.
SET UP appears.
2 Turn M.C. to switch to YES.
# If you do not operate for 30 seconds, the set up
menu will not be displayed.
# If you prefer not to set up at this time, turn M.C.
to switch to NO. Press to select.
If you select NO, you cannot set up in the set up
menu.
3 Press M.C. to select.
4 Perform the following procedures to set
the menu.
To proceed to the next menu option, you need to
confirm your selection.
Operating this unit
CLOCK SET (setting the clock)
1 Turn M.C. to adjust hour.
2 Press M.C. to select minute.
3 Turn M.C. to adjust minute.
4 Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
! The tuning step remains at 50 kHz during man-
ual tuning.
1 Turn M.C. to select the FM tuning step.
50 (50 kHz)—100 (100 kHz)
2 Press M.C. to confirm the selection.
AM STEP (AM tuning step)
The AM tuning step can be switched between
9 kHz and 10 kHz.
1 Turn M.C. to select the AM tuning step.
9 (9 kHz)—10 (10 kHz)
2 Press M.C. to confirm the selection.
QUIT appears.
5 To finish your settings, turn M.C. to select
YES.
# If you prefer to change your setting again, turn
M.C. to switch to NO. Press to select.
6 Press M.C. to select.
Notes
! You can set up the menu options from the
system menu. For details about the settings,
refer to System menu on page 8.
! You can cancel set up menu by pressing
SRC/OFF.

Basic operations

Important
! Handle gently when removing or attaching
the front panel.
! Avoid subjecting the front panel to excessive
shock.
! Keep the front panel out of direct sunlight
and high temperatures.
! To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached
to the front panel before detaching it.
Section
02
3
En