Current Audio AMP-1270 Instruction Manual

Current Audio AMP-1270 Instruction Manual

Multi-channel 70 watt digital class d amplifier
Hide thumbs Also See for AMP-1270:

Advertisement

Multi-Channel 70 Watt Digital
Class D Amplifier
Now with Auto Sensing
Instruction Manual
www.currentaudio.com
©2013 Current Audio LLC
1
1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181
AMP1270 RPA 11152013

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AMP-1270 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Current Audio AMP-1270

  • Page 1 Multi-Channel 70 Watt Digital Class D Amplifier Now with Auto Sensing Instruction Manual www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 2: Safety Instructions

    This product conforms to all EU Directive requirements as applicable by law. The complete Declaration of Conformity can be found at compliance.currentaudio.com www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 3: Specifications

    Thank you for purchasing a Current Audio Multi-Channel Amplifier. Please read this manual thoroughly before making any connections or applying AC power. This manual applies to both the AMP-1270 and the AMP-870. The AMP-870 has fewer channels (eight) compared to the AMP-1270 with twelve channels.
  • Page 4 Welcome to D-Force by Current Audio D-Force describes the latest digital technology in amplifiers by Current Audio. The D- Force amplifiers generate the equivalent analog output for speakers by using a modulated audio signal rather than the traditional digital to analog conversion. Because this amp uses pulse modulation, the efficiency is 90% compared to 50% of analog.
  • Page 5 IEC POWER-IN CONNECTOR Plug female IEC cord here. Observe selected voltage. Also houses the main fuse. Replace only with correct fuse. www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 6: Getting Started

    Getting Started Amplifier Placement Current Audio D-Force amplifiers require plenty of free air space for safe and proper operation. The following diagram indicates the minimum amount of free air space to provide the proper ventilation and heat exchange. Anything less than this will shorten the life of the equipment and may cause the amp to shut down.
  • Page 7: Speaker Outputs

    Red of the speaker and the Black (-) of the amp to the Black (-) of the speaker. If they are connected out of phase, the mid and low frequencies will cancel and the speakers will not perform as intended. www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 8: Loop Output

    Caution: Before making any changes to the Bridged or Global In switch positions insure that the Master Power switch on the rear of the amp is OFF. Possible damage to the amp may occur due high transient current during switching or from wiring misconfiguration. Global In/Line In Switch This switch allows the user to select the source for each zone from the Global In Input or a separate source input via the Line In Input on each zone.
  • Page 9 The tip of the plug is (+). Auto Mode Music. In this mode the amp will energize automatically by sensing a small current when an audio signal is applied. The Front Panel ON/STANDBY Switch must be in Standby mode. The switch LED will indicate red.
  • Page 10 Zone 5 Zone 6 Zone 1 Zone 2 Zone 4 Zone 3 Bridged Output Normal Output for Stereo for Stereo (Note Inputs) www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105nue El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 11 OC8B Zone 5 Zone 6 Zone 2 Zone 1 Zone 4 Zone 3 Bridged Output Normal Output for Stereo for Stereo www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105nue El Cajon, CA 92020 Sales 866-927-7181 AMP1270 RPA 11152013...
  • Page 12: Troubleshooting

    Make sure the Switch is in standby mode Power Switch on front panel Not Working indicated by a RED light. BLUE when triggered. www.currentaudio.com ©2013 Current Audio LLC 1890 Cordell Court, Suite 105 El Cajon, CA 92020 Sales 866-927-7181 AMP870 RPA 11152013...
  • Page 13: Warranty

    Limited 1 Year Warranty Current Audio, LLC amplifiers are warranted to be free from defects in materials and or workmanship to the original retail purchaser for a period of 1 year, provided the equipment was purchased and installed from a Current Audio, LLC Authorized Dealer or Distributor.

This manual is also suitable for:

Amp-870

Table of Contents

Save PDF