Table of Contents
Advertisement
Available languages
Available languages
Operating this unit
CAUTION
For safety reasons, park your vehicle when re-
moving the front panel.
Notes
! When this unit's blue/white lead is con-
nected to the vehicle's auto-antenna relay
control terminal, the vehicle's antenna ex-
tends when this unit's source is turned on.
To retract the antenna, turn the source off.
! When there are two USB storage devices
connected to this unit and you want to
switch between them for playback, discon-
nect communications for the USB storage
device first before proceeding.
! If connecting both USB1 (USB storage de-
vice1)/iPod1 (iPod connected using USB
input1) and USB2 (USB storage device2)/
iPod2 (iPod connected using USB input2) at
the same time, use a Pioneer USB cable
(CD-U50E) in addition to the regular Pioneer
USB cable.
Use and care of the remote
control
Using the remote control
1 Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1 Slide the tray out on the back of the remote
control.
2 Insert the battery with the plus (+) and minus
(–) poles aligned properly.
WARNING
! Keep the battery out of the reach of children.
Should the battery be swallowed, consult a
doctor immediately.
! Batteries (battery pack or batteries installed)
must not be exposed to excessive heat such
as sunshine, fire or the like.
CAUTION
! Use one CR2025 (3 V) lithium battery.
! Remove the battery if the remote control is
not used for a month or longer.
! There is a danger of explosion if the battery is
incorrectly replaced. Replace only with the
same or equivalent type.
! Do not handle the battery with metallic tools.
! Do not store the battery with metallic ob-
jects.
! If the battery leaks, wipe the remote control
completely clean and install a new battery.
! When disposing of used batteries, comply
with governmental regulations or environ-
mental public institutions' rules that apply in
your country/area.
Important
! Do not store the remote control in high tem-
peratures or direct sunlight.
! The remote control may not function properly
in direct sunlight.
! Do not let the remote control fall onto the
floor, where it may become jammed under
the brake or accelerator pedal.
Operating this unit
Menu operations identical
for function settings/audio
adjustments/initial settings/
lists
Returning to the previous display
Returning to the previous list/category. (the folder/
category one level higher.)
1 Press
/DISP.
Turning the demo display on or off
1 Press and hold
/DISP.
Returning to the ordinary display
Canceling the initial setting menu
1 Press BAND/ .
Returning to the ordinary display from the list/cat-
egory
1 Press BAND/ .
Selecting a function or list
1 Turn LEVER or M.C.
! In this manual, "Turn LEVER" is used to de-
scribe the operation used to select a function
or list.
Tuner
Basic operations
1
2
3
4
5
6 7
8
RDS
1
2
3
5
9
Non-RDS or AM
1 Band indicator
2 5 (stereo) indicator
3 LOC indicator
Appears when local seek tuning is on.
4 Preset number indicator
5 Signal level indicator
6 TEXT indicator
Shows when the radio text is received.
7 PTY label indicator
8 Program service name
9 Frequency indicator
Selecting a band
1 Press BAND/
until the desired band (FM-1,
FM-2,FM-3 for FM or AM) is displayed.
Manual tuning (step by step)
1 Turn LEVER.
Seeking
1 Turn and hold down LEVER.
! While turning and holding down LEVER,
you can skip stations. Seek tuning starts
as soon as you release LEVER.
Using PI Seek
If the tuner cannot find a suitable station, or the
reception status deteriorates, the unit automati-
cally searches for a different station with the
same programming. During the search, PI seek
is displayed and the sound is muted.
Section
02
5
En
Advertisement
Table of Contents
