Invacare ICCG 1143214 Installation And Operating Instructions Manual
Invacare ICCG 1143214 Installation And Operating Instructions Manual

Invacare ICCG 1143214 Installation And Operating Instructions Manual

Icci bed rails and accessories

Advertisement

Quick Links

ICCI Bed Rails and Accessories
Assembly, Installation and Operating Instructions
Part No. 6801A, 6803A, 6808A, 6815A, 6816A, IH5748A, IHRAILTS-DLX
NOTE: Check all parts for shipping damage before using. In case of damage, DO NOT use the equipment. Contact the
Dealer/Carrier for further instructions.
DO NOT use this product or any available optional equipment without first completely reading and
understanding these instructions and any additional instructional material such as owner's manuals, service
manuals or instruction sheets supplied with this product or optional equipment. If you are unable to understand
the warnings, cautions or instructions, contact a healthcare professional, dealer or technical personnel before
attempting to use this equipment - otherwise, injury or damage may occur.
These bed rails are intended to prevent an individual from inadvertently rolling out of bed. DO NOT use for
restraint purposes.
DO NOT use the bed rails as push handles for moving the bed.
ALWAYS test to make sure that the bed rails are properly and securely in place before using.
Although bed rails are not rated to any specific weight limitation, the bed rails may become deformed or broken
if excessive side pressure is exerted on the bed rails. This bed rail is not an assist rail for getting into or out of
bed. DO NOT use the bed rails as push handles when moving the bed.
Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories.
Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for
use with Invacare products.
Proper patient assessment and monitoring, and proper maintenance and use of equipment is required to reduce
the risk of entrapment. Variations in bed rail dimensions, and mattress thickness, size or density could increase
the risk of entrapment. Visit the FDA website at http://www.fda.gov to learn about the risks of entrapment.
Review "A Guide to Bed Safety", published by the Hospital Bed Safety Workgroup.
Refer to the bed owner's manuals for additional product and safety information.
Mattress MUST fit bed frame and bed rails and/or positioning device snugly to reduce the risk of entrapment.
After any adjustments, repair or bed service and before use, make sure all attaching hardware is tightened
securely. Rails and/or positioning devices with dimensions different from the original equipment supplied or spec-
ified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury.
Installing/Using the Epoxy Bed Rails
NOTE: For this procedure, refer to FIGURE 1.
Installing 6801A and 6808A Bed Rails
1.
Position the pivot brackets on the bed frame as shown in Details "A" and "B" of FIGURE 1.
2.
Loosely attach the pivot brackets to the bed frame with the hex bolts and locknuts.
NOTE: DO NOT tighten the hex bolts and locknuts at this time.
3.
Slide the mounting pins of the bed rails through the pivot tubes.
NOTE: Make sure the release lever on the bed rail is pointing towards the foot end of the bed.
For more information regarding Invacare Continuing Care, Inc. (ICCI) products, parts, and services,
Part No 1143214
SAVE THESE INSTRUCTIONS
Safety Summary
WARNING
ACCESSORIES WARNING
ENTRAPMENT WARNING
please visit www.invacare-ccg.com or call 800-668-2337
1
ICCI Bed Rails and Accessories

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ICCG 1143214 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Invacare ICCG 1143214

  • Page 1 DO NOT use the bed rails as push handles when moving the bed. Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.
  • Page 2 Bed Rail (on the outside of bed frame) See Detail A Bed Frame DETAIL “A” - HEAD END TOP VIEW Mounting Pin Socket Screw Inside of Bed Frame Bed Rail (on the outside of bed frame) FIGURE 1 Installing 6801A and 6808A Bed Rails Install a socket screw into the head end and foot end mounting pins and tighten securely.
  • Page 3 Release Lever Towards the foot end of the bed) Mounting Mounting Bracket Pivot Tube Locknut Attach Head End Crossmember Here Head End Mounting Hole FIGURE 2 Installing 6815A, 6816A and 6803A Bed Rails Secure the bed rail to the mounting bracket with the two socket screws. Head End Mounting Bracket Only - Position the crossmember between the two bed rails as shown in Detail “A”...
  • Page 4 NOTE: For this procedure, refer to FIGURE 4 on page 4. NOTE: Invacare recommends two people perform the following installation procedure. One person should hold the bed rail up against the bed and one person should attach the rail to the bed.
  • Page 5 Installing/Using the Carroll Assist Rail Installing/Using IHRAILAB-DL and IHRAILAE-DLX For instruction involving installation and use of the Carroll Assist Rails and Carroll Assist Bar, refer to the instruction sheet included with the rails. Installing/Using the ThinkSoft®Positioning Device DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets supplied with this product or optional equipment.
  • Page 6 IHRAILTS-DLX Positioning Device Release Lever (Towards the foot end of the bed) Mounting Pin Washer Hex Bolt Mounting Bracket Pivot Tube Locknut Attach Head End Crossmember Here FIGURE 7 Installing the IHRAILTS-DLX Positioning Device Using the IHRAILTS-DLX Positioning Device NOTE: For this procedure, refer to FIGURE 8. Perform one of the following: •...
  • Page 7 DETAIL “A” NOTE: Mounting position of head board mounting bracket for use with 80-inch mattress - without side rails 2-inch Gap Mounting Screws and Locknuts Head Board Mounting Bracket FIGURE 9 Changing the Head Board Mounting Position Changing the Mounting Position of the Mattress Keepers NOTE: For this procedure, refer to FIGURE 10 on page 7.
  • Page 8: Special Note

    For your convenience, the January 2008 version of the FDA’s bed safety guidelines are provided in this section. The information from the FDA’s brochure, published by Hospital Bed Safety Workgroup, is reproduced verba- tim, the latest revision of which is available at http://www.fda.gov. A Guide to Bed Safety Bed Rails in Hospitals, Nursing Homes and Home Health Care: The Facts Bed Rail Entrapment Statistics...
  • Page 9: Which Ways Of Reducing Risks Are Best

    When bed rails are used, perform an on-going assessment of the patient’s physical and mental status; closely monitor high-risk patients. Consider the following: • Lower one or more sections of the bed rail, such as the foot rail. • Use a proper size mattress or mattress with raised foam edges to prevent patients from being trapped between the mattress and rail.
  • Page 10 NOTES ICCI Bed Rails and Accessories Part No 1143214...
  • Page 11: This Warranty Shall Be Extended To Comply With State/Provincial Laws And Requirements

    This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare Continuing Care, Inc. or a dealer. This warranty is not extended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner. Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person.
  • Page 12 A subsidiary of Invacare Corporation. All rights reserved. Trademarks are identified by the symbols ™ and ®. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. ©2009 Invacare Corporation Part No 1143214 Rev E - 3/09...

This manual is also suitable for:

6808a6801a6815a6816a6803aIh5748a ... Show all

Table of Contents