Machine Data Log / Overview OVERVIEW The Ninja Warrior is an electric powered carpet extractor intended for commercial use. This appliance applies a cleaning solution to the carpet and then vacuums the soiled water back into the recovery tank. 86322430 NINJA WARRIOR 150 PSI...
KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower left corner of the front cover. 86322430 NINJA WARRIOR 150 PSI...
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes. Maintenance and repairs must be done by qualified personnel. If foam or liquid comes out of machine, switch off immediately. SAVE THESE INSTRUCTIONS 86322430 NINJA WARRIOR 150 PSI...
In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use only manufacturer approved replacement parts. 86322430 NINJA WARRIOR 150 PSI...
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. Label Warning 86244300 PRV # 500955 WARNING! FOR YOUR PROTECTION USE A GROUND FAULT CIRCUIT INTERRUPTER Label Circuit Interrupter 86200570 PRV # 170-41 86322430 NINJA WARRIOR 150 PSI...
NOTE: When using a powder cleaner, pre-mix with hot water in a clean container before adding to the solution tank. 6. Turn pump and vacuum switch(s) to the on position. 86322430 NINJA WARRIOR 150 PSI...
When this occurs, empty the vacuum tank by opening the dump valve and dispose of the waste in a proper manner. Once the vacuum tank has been emptied, you may once again proceed with cleaning. 86322430 NINJA WARRIOR 150 PSI...
Check all gaskets for wear and leakage Check pump pressure; observe spray pattern and check with gauge if necessary Check and clean solution screen Check cables for fraying Check overall performance of machine Check vac motor carbon brushes 86322430 NINJA WARRIOR 150 PSI...
Spring inside brush housing will damage motor if brushes are allowed to wear away completely. 8 [9.5mm] Periodically check the length of the carbon brushes. Replace both carbon brushes when either is less than 3/8" (9.5mm) long. 86322430 NINJA WARRIOR 150 PSI...
Page 21
SWITCH, SPST 2-POSITION ROCKER 86008900 80845 BOOT, SEAL PUSH BUTTON 7/16 86323520 PANEL, CONTROL, 150 86313020 GASKET, .125 T X .25 W X 15.6 86313030 GASKET, .125 T X .25 W X 7.2 86318320 BREAKER, 13A, 250VAC, 32VDC 86322430 NINJA WARRIOR 150 PSI...
-VACUUM -PUMP SWITCH SWITCH SWITCH -POWER CORD 13AMP 13AMP -TERMINAL BLU/1 BLU-BLK/2 GRY/3 BLOCK -FUSE 4AMP BLK-WHT GRY-WHT WHT/7 WHT/8 M M M M M M M M M -VACUUM -VACUUM -PUMP MOTOR MOTOR MOTOR 86322430 NINJA WARRIOR 150 PSI...
Page 45
Wiring - 2 Stage Vacuum SERIAL NO. PART NO. PRV NO. DESCRIPTION NOTES FROM 98407900 HARNESS KIT, SINGLE CORD 86322430 NINJA WARRIOR 150 PSI...
BLU/1 BLU-BLK/2 GRY/3 BRN/13 WHT/14 -TERMINAL BLOCK BLK/5 BRN-WHT -FUSE BLK-WHT/4 15AMP YEL/12 GRY-WHT BRN/16 BRN/16 -FUSE 4AMP WHT/15 JUMPER WHT/7 WHT/8 M M M M M M -VACUUM -VACUUM -PUMP MOTOR MOTOR MOTOR -HEATER 86322430 NINJA WARRIOR 150 PSI...
Page 47
Wiring with Heat SERIAL NO. PART NO. PRV NO. DESCRIPTION NOTES FROM 98407920 HARNESS KIT, HEATED 86322430 NINJA WARRIOR 150 PSI...