Prior To Using For The First Time; Setting Electronically; Setting The Water Softener; Setting Manually - Zanussi DE 6854 Instruction Book

Prior to using for the first time

Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions.
2. Remove all packaging from inside the appliance.
3. Set the water softener.
4. Pour 1 litre of water inside the salt container and then fill
with salt.
5. Fill the rinse aid dispenser.
6. Run a "Rinse and Hold" programme.

Setting the water softener

The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these salts, the harder your water is.
Water hardness is measured in equivalent scales, Clarke
degrees, French degrees and PPM (parts per Million).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using
the water hardness switch and electronically, using the function
push buttons on the control panel.
If your water is level 1 it is already soft and therefore there
is no need to use salt.

Setting manually

1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness switch to position 1 or 2 (see
table).
4. Replace the lower basket.
The dishwasher is factory set
at position 2.
Clarke
degrees
50 - 63
36 - 49
22 - 35
6 - 21
< 6
AA07
Water hardness
French
PPM
degrees
(parts per million)
(°TH)
71 - 90
701 - 900
51 - 70
501 - 700
31 - 50
301 - 500
8 - 30
80 - 300
< 8
< 80

Setting electronically

The dishwasher is factory set at level 3. If it's necessary to set
a new level, proceed as follows.
1. With the dishwasher switched off press function push
buttons 1 and 2 simultaneously .
2. While keeping the push buttons 1 and 2 pressed switch on
the dishwasher by pressing the On/Off push button.
The On/Off indicator light comes on.
At the same time, the indicator lights of push buttons 1 and
2 start flashing.
3. Press push button 1, the indicator light of push button 2
turns off, while the indicator light of push button 1 remains
fixed for about 5 seconds, after this it starts flashing
indicating the current level of the water softener.
The current level is indicated by the number of flashes
made by the indicator light of push button 1, that alternates
5 seconds off with a number of flashes, this for about 60
seconds.
Example:
1 flash = level 1
2 flashes = level 2
3 flashes = level 3
4 flashes = level 4
5 flashes = level 5
4. To change the level, press push button 1. Each time the
push button is pressed the level changes.
Example:
if the current level is 3, by pressing push button 1 once,
level 4 is selected.
if the current level is 5, by pressing push button 1 once,
level 1 is selected.
The indicator light of push button 1 remains off for about 5
seconds after which it starts flashing indicating the new
level selected.
5. To memorise the new level, switch off the dishwasher by
pressing the On/Off push button.
Adjusting the water hardness
setting
manually electronically
2 level 5
level 4
2
2 level 3
1 level 2
1 level 1
5
SO568
SO569
Use of
Number of
salt
flashes
5
yes
4
yes
3 yes
2
yes
1
no