Table of Contents
Advertisement
Prior to using for the first time
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and then fill
with dishwasher salt
5. Fill the rinse aid dispenser
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these minerals and salts, the harder
your water is.
Water hardness is measured in equivalent scales, Clarke
degrees, French degrees and mmol/l (millimol per litre).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using
the water hardness switch and electronically, using the function
push buttons on the control panel.
a) Setting manually
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn the water hardness switch to position 1 or 2 (see
table).
4. Replace the lower basket.
The dishwasher is factory set
at position 2.
Water hardness
Clarke
°TH
degrees
(french degrees)
64 - 88
91 - 125
53 - 63
76 - 90
65 - 75
46 - 52
36 - 45
51 - 64
28 - 35
40 - 50
23 - 27
33 - 39
18 - 22
26 - 32
19 - 25
13 - 17
5 - 12
7 - 18
< 5
< 7
AA07
mmol/l
Range
(millimol per litre,
international unit for the
hardness of water)
9,0 - 12,5
IV
7,6 - 8,9
IV
6,5 - 7,5
IV
5,1 - 6,4
IV
4,0 - 5,0
IV
3,3 - 3,9
III
2,6 - 3,2
III
1,9 - 2,5
II
0,7 - 1,8
I/II
< 0,7
I
b) Setting electronically
(The dishwasher must be switched off)
The dishwasher is factory set at level 5.
1. Press the On/Off push button. All programme selection push
buttons indicator lights will illuminate (setting mode).
If only one programme selection push button indicator light
is illuminated, this means that a washing programme has
been selected.
The programme must be cancelled: press simultaneously
the function push buttons 2 and 3 for about 2 seconds, the
indicator light of the set programme push button starts
flashing for about 2 seconds. After about 2 seconds the
indicator lights of all the programme selection push buttons
will illuminate indicating that the set programme has been
cancelled and that the machine is now in setting mode.
2. Press simultaneously function push buttons 2 and 3, until
the indicator lights of the function push buttons 1, 2 and 3
start flashing.
3. Press the function push button 1, the indicator lights of
function push buttons 2 and 3 turn off while the indicator
light of the push button 1 goes on flashing, at the same time
the END OF CYCLE indicator light illuminates, along with a
sequence of audible signals.
The current level is indicated by the number of flashes of
the END OF CYCLE indicator light and of audible signals
heard.
Example:
5 flashes + 5 audible signals = level 5.
4. To change the level, press push button 1. Each time the
push button is pressed the level changes. (For the selection
of the new level see the chart).
Examples:
if the current level is 5, by pressing push button 1 once,
level 6 is selected.
if the current level is 10, by pressing push button 1 once,
level 1 is selected.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off push button or wait about 60 seconds
after which the dishwasher will automatically return to
setting mode.
Adjusting
the water
hardness setting
manually
electronically
2
level 10
2
level 9
2
level 8
2
level 7
2
level 6
2
level 5
1
level 4
1
level 3
1
level 2
1
level 1
6
Number of flashes of
the END OF CYCLE
indicator light and of
audible signals
10
9
8
7
6
5
4
3
2
1
Use
of salt
yes
yes
yes
yes
yes
yes
yes
yes
yes
no
Hide quick links:
Advertisement
Table of Contents
