Subscribe to Our Youtube Channel
Related Manuals for Arbor Technology P0715
Summary of Contents for Arbor Technology P0715
- Page 1 Quick Installation Guide Version 1.0 P0715 7" Compact Intel Low Voltage PIII / Celeron Panel PC...
- Page 2 This manual provides general information and installation instructions about the product. This Quick Installation is intended for experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this Quick Installation, please consult your vendor before further handling. P0715 Quick Installation...
- Page 3 5. It possibly needs BIOS support in the case of using special backplane, otherwise, it might be not able to function completely. 6. Please make sure the power connector is tightly plugged into the power socket before power on. P0715 Quick Installation...
-
Page 4: Getting Started
Getting Started This section will help you have your P0715 up and running smoothly. P0715 9 x Screws 1 x Arm Holder Bracket 2 x Wall Mount Bracket 1 x Adaptor 2 x Power Cord (American & French Cordset) 1 x Driver CD Before up and running, please make sure the package contains all of above accessories. -
Page 5: Specification
Dimension (L x H x D) P0715 Quick Installation Specification Panel PC P0715 Intel Low Voltage Celeron 400~733MHz CPU FSB100/133MHz 2nd Level 256K 1 x 144Pin SO-DIMM up to 512MB SDRAM SMI722 G8 Lynx 3D+ engine 8MB Video RAM on chip... - Page 6 Mounting Arm Mounting Hook Mounting P0715 Quick Installation...
- Page 7 Dimension Unit: mm P0715 Quick Installation...
- Page 8 OSD of Front Panel P0715 Quick Installation...
-
Page 9: Location Of I/O Ports
HDD (if pre-installed). The front panel does not contain any indicators, switches, connectors or drive access. All these are to be found on the left and right side and on the rear of the system. Default I/O P0715 Quick Installation... -
Page 10: Connecting Peripherals
600, it won't display completely at first when you connect the monitor. External Serial Ports (COM1/2) The P0715 logic board supports four onboard serial ports, all COM ports supports RS-232. The external COM1, COM2 are all D-SUB 9-pin connectors. To connect any serial device, follow the following instructions: 1. - Page 11 2. Plug in one end of cable of a 100/10 Base-T hub to the system's RJ-45 jack. USB Ports P0715 provides four external USB ports to connect to external USB devices. USB ports and devices are hotplug capable. Therefore any USB device can be connected at all time without the need to power down your system.
-
Page 12: Hardware Installation
Hardware Installation HDD installation 1. On the back of P0715, locate the screws that secure the rear case. Use screw driver to remove the screws. Keep the screws safely for later use. Pull the baffle slightly upward the main unit until it is disen- gaged from main unit. - Page 13 44 pin IDE Cable 2.5" HDD Pin 1 Pin 1 Note: Beware of the directions when wiring HDD and IDE cable. P0715 Quick Installation...
- Page 14 Panel PC Installation 1. In 2.4B or above Driver, choose Drivers & Utili- ties. P0715 Quick Installation...
- Page 15 1.1 Select Panel Computing. P0715 Quick Installation...
- Page 16 1.2 Select P0715. P0715 Quick Installation...
- Page 17 1.3 Install All Drivers. P0715 Quick Installation...
- Page 18 2. Install Touch Screen Driver. P0715 Quick Installation...
- Page 19 4. Select Promote Touch Driver to install. P0715 Quick Installation...
Need help?
Do you have a question about the P0715 and is the answer not in the manual?
Questions and answers