Subscribe to Our Youtube Channel
Related Manuals for Arbor Technology P1215
Summary of Contents for Arbor Technology P1215
-
Page 1: Quick Installation Guide
Quick Installation Guide Version 1.0 P1215 12.1" Slim-Size Intel Low Voltage PIII / Celeron Panel PC... - Page 2 This manual provides general information and installation instructions about the product. This Quick Installation is intended for experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this Quick Installation, please consult your vendor before further handling. P1215 Quick Installation...
- Page 3 5. It possibly needs BIOS support in the case of using special backplane, otherwise, it might be not able to function completely. 6. Please make sure the power connector is tightly plugged into the power socket before power on. P1215 Quick Installation...
-
Page 4: Getting Started
Getting Started This section will help you have your P1215 up and running smoothly. PACKING LIST P1215 1 x DC-DC Adapter 4 x Screws 4 x LCD Hook 1 x Grounding Cable 1 x IDE Cable 1 x Print Cable... - Page 5 Specification Model Name Panel PC P1215 Intel Low Voltage Celeron 400~733MHz CPU FSB100/133MHz Cache 2nd Level 256K default 256MB SDRAM on board, up to 512MB Memory (1 x 144 pin SO-DIMM Socket) System VRAM SMI722 G8 Lynx 3D+ engine 8MB Video RAM on chip...
- Page 6 Mounting Wall Mounting P1215 Quick Installation...
- Page 7 P1215 Quick Installation...
- Page 8 Dimension Unit: mm P1215 Quick Installation...
-
Page 9: Location Of I/O Ports
HDD (if pre-installed). The front panel does not contain any indicators, switches, connectors or drive access. All these are to be found on the left and right side and on the rear of the system. Default I/O P1215 Quick Installation... -
Page 10: Connecting Peripherals
Connecting an exter- nal CRT P1215 has a 15-pin analog RGB interface connector located at the rear side of the chassis for connection a secondary display. The system can support simultaneous display on both its LCD display and on the external CRT display. -
Page 11: Usb Ports
LAN Port P1215 provides one 100/10 Base-T Ethernet (RJ-45) interface. For network connection, follow the instructions below; 1. Turn off the Panel PC system and the Ethernet hubs. 2. Plug in one end of cable of a 100/10 Base-T hub to the system's RJ-45 jack. -
Page 12: Parallel Port
EPP and ECP parallel port protocolsto be used to connect a wide array of printers, ZIP drive, parallel scanner and any other parallel devices. The printer interface on the P1215 is a 25-pin female D-SUB connector. To connect any parallel device, follow the steps below: 1. -
Page 13: Hardware Installation
Hardware Installation HDD installation 1. On the back of P1215, locate the screws that secure the rear case. Use screw driver to remove the screws. Keep the screws safely for later use. Pull the baffle slightly upward the main unit until it is disen- gaged from main unit. - Page 14 2. Pull the HDD Holders upward the main unit until they are disengaged from main unit. P1215 Quick Installation...
- Page 15 3. Place the 2.5" HDD between two HDD Holders and use the screwdriver to screw them on tightly. P1215 Quick Installation...
- Page 16 44 pin IDE Cable 2.5" HDD Pin 1 Pin 1 Note: Beware of the directions when wiring HDD and IDE cable. P1215 Quick Installation...
- Page 17 Panel PC Installation 1. Choose Drivers & Utilities. P1215 Quick Installation...
- Page 18 1.1 Select Panel Computing. P1215 Quick Installation...
- Page 19 1.2 Select P1215. P1215 Quick Installation...
- Page 20 1.3 Install All Drivers. P1215 Quick Installation...
- Page 21 2. Install Touch Screen Driver. 2.1 Select All Touch Screen. P1215 Quick Installation...
- Page 22 2.2. Select Fujitsu Touch Screen Driver to install. Please select Browse CD and double click RTPsetup.exe file. P1215 Quick Installation...
Need help?
Do you have a question about the P1215 and is the answer not in the manual?
Questions and answers