Related Manuals for DeWalt DC628-XE
Summary of Contents for DeWalt DC628-XE
- Page 1 INSTRUCTION MANUAL DC628-XE DC629-XE (Sequential Fire Action only) 15 GAUGE CORDLESS NAILER...
-
Page 2: Tool Specifications
Definitions: Safety Guidelines The definitions below describe the level of severity for each signal Angled 34˚ word. Please read the manual and pay attention to these symbols. FIG. 1 DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. - Page 3 IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS • Use safety equipment. Always wear eye protection. Dust mask, • Always wear appropriate personal hearing and FIG. A OR ANY D WALT TOOL, CALL US AT: 1800 654 155 (Aust) or non-skid safety shoes, hard hat, or hearing protection must be other protection during use.
- Page 4 careful not to lose footing when working in elevated • Be aware of material thickness when using nailer. A FIG. G FIG. M CAUTION: When not in use, place tool on its side on a environments such as rooftops. protruding nail may cause injury. stable surface where it will not cause a tripping or falling hazard.
- Page 5 • DO NOT attempt to charge the battery pack with any chargers 1. The red light will blink continuously indicating that the NOTE: Battery storage and carrying caps are provided other than the ones in this manual. The charger and battery pack are 1-hour charge cycle has started.
-
Page 6: Operation
Mode Selection HOT/COLD PACK DELAY WARNING: Shock hazard. Don’t allow any liquid to get inside charger. Some chargers have a Hot/Cold Pack Delay feature: when the charger Electric shock may result. To facilitate the cooling of the battery pack after WARNING: ALWAYS wear proper eye [ANSI Z87.1 (CAN/CSA Z94.3)] and detects a battery that is hot, it automatically starts a Hot Pack Delay, use, avoid placing the charger or battery pack in a warm environment such... -
Page 7: Maintenance
Preparing the Tool 3. Lift the jam clearing latch (E) then pull up to open front door (O). UNLOADING THE TOOL 4. Remove bent nail, using pliers if necessary. CAUTION: The contact trip lock-off should always be locked off CAUTION: NEVER spray or in any other way 5. - Page 8 3. Push driver/return assembly (R) toward nosepiece and hold in place 2. Move contact trip (Z) to the side while pulling back on the return cord ACTION Before each use, check to insure all screws, nuts and fasteners against the lower bumper (V) as you roll back the activation arm assembly (Fig.
- Page 9 30 DAY NO SATISFACTION GUARANTEE In addition to the warranty, D WALT tools are covered by our: If you are dissatisfied with any D WALT power tool, laser or nailer, for any FREE ONE YEAR SERVICE CONTRACT reason, simply return it to the point of purchase with your sales receipt within WALT will also maintain the tool for free at any time during the first year of 30 days for a replacement unit or a full refund.
-
Page 10: Troubleshooting Guide
TROUBLESHOOTING GUIDE MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D WALT SERVICE CENTER OR CALL 1800 654 155 (Aust) or 09 5291111 (NZ) DISCONNECT BATTERY PACK FROM TOOL WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS BEFORE ALL REPAIRS SYMPTOM... - Page 12 20 Fletcher Road, Mooroolbark, VIC 3138 Australia (03 8720 5100) • 5 Te Apunga Place, Mt Wellington, New Zealand (09 259 1111) (MAY07) Form No. 649521-00 DC628-XE, DC629-XE Copyright © 2007 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...