DeWalt DC608 Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Nail Gun
  5. DC608
  6. Instruction manual

DeWalt DC608 Instruction Manual

18 gauge cordless nailer
Hide thumbs Also See for DC608:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
Before returning this product call
1-800-4-D
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DC608
18 Gauge Cordless Nailer
Cloueuse sans fil pour clou de calibre 18
Clavadora inalámbrica de calibre 18
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR D
WALT
E
Questions? Visit us at www.dewalt.com
Des questions ? Rendez nous visite à www.dewalt.com
¿Tiene preguntas? Visítenos en www.dewalt.com
CALL 1-800-4-D
IN MOST CASES, A D
WALT REPRESENTATIVE CAN RESOLVE
E
YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D
IMPROVEMENT PROGRAM.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
WALT PURCHASE,
E
WALT
E
WALT'S QUALITY
E

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DC608

Summary of Contents for DeWalt DC608

  • Page 1 YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D WALT’S QUALITY IMPROVEMENT PROGRAM. Questions? Visit us at www.dewalt.com Des questions ? Rendez nous visite à www.dewalt.com ¿Tiene preguntas? Visítenos en www.dewalt.com INSTRUCTION MANUAL INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

  • Page 2: Defi Nitions: Safety Guidelines

    FIG. 1 Defi nitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

  • Page 3: Save All Warnings And Instructions For Future Reference

    IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, e) Do not overreach. Keep proper footing and balance at all times. This enables CALL US TOLL FREE AT: 1-800-4-D WALT (1-800-433-9258). better control of the power tool in unexpected situations. f) Dress properly.
  • Page 4 • Do not point the tool towards yourself • Disconnect battery pack from the • Use the tool only for its intended FIG. A FIG. G or anyone nearby. Unexpected triggering tool when not in use. Always remove use. Do not discharge fasteners will discharge a fastener causing an injury.

  • Page 5: Important Safety Instructions For All Battery Packs

    • Keep face and body parts away from back of the tool cap FIG. M WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other when working in restricted areas. Sudden recoil can result construction activities contains chemicals known to the State of California to cause cancer, in impact to the body, especially when nailing into hard or dense birth defects or other reproductive harm.

  • Page 6: Important Safety Instructions For All Battery Chargers

    • Charge the battery packs only in D WALT chargers. The RBRC Seal • DO NOT splash or immerse in water or other liquids. The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel • Do not store or use the tool and battery pack in locations where the temperature cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate may reach or exceed 105 °F (40 °C) (such as outside sheds or metal buildings in that the costs to recycle these batteries (or battery packs) at the end of their...
  • Page 7 one extension to make up the total length, be sure each individual extension contains at Charging Procedure (Fig. 2) least the minimum wire size. The following table shows the correct size to use depending DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe on cord length and nameplate ampere rating.

  • Page 8: Operation

    NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery COMPONENTS pack has not been kept on maintenance charge, it may need to be recharged before use. WARNING: Lock the contact trip in the off position, disconnect battery pack from tool and A battery pack may also slowly lose its charge if left in a charger that is not plugged into an remove nail strips from magazine before making adjustments or personal injury may result.

  • Page 9: Loading The Tool

    FIG. 5 2. Wear eye and ear protection. 3. Remove battery from tool. 4. Ensure magazine is empty of all fasteners. 5. Check for smooth and proper operation of contact trip and pusher assemblies. Do not use tool if either assembly is not functioning properly. NEVER use a tool that has the contact trip restrained in the actuated position.

  • Page 10: Maintenance

    11. Disengage contact trip lock-off, allowing the contact trip to move. WARNING: To reduce risk of serious injury from accidental actuation when NOTE: Should nails continue to jam frequently in nosepiece, have tool serviced by an attempting to adjust depth, ALWAYS: authorized D WALT service center.
  • Page 11 D WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D WALT (1-800-433-9258) or visit our website: www.dewalt.com. Repairs WARNING: To reduce the risk of serious personal injury, remove nails from magazine before making any adjustments or servicing this tool.

  • Page 12: Troubleshooting Guide

    MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D WALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT. WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS DISCONNECT BATTERY PACK FROM TOOL...

Table of Contents