Advertisement
EN
FR
DE
ES
IT
PT
■ Hold the blower with both hands.
■ To avoid from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the
center of a pile.
■ Operate power equipment during normal hours only –
not early in the morning or late at night when people
might be disturbed. Comply with the operating hours
listed in local ordinances.
■ To reduce sound levels, limit the number of equipment
used at any one time.
■ Operate blower at the lowest possible throttle speed.
■ Check your equipment before operation, especially
the silencer, air intakes and air filters.
■ Loosen debris before blowing. In dusty conditions,
slightly dampen surfaces.
■ Watch out for children, pets, open windows or freshly
washed cars.
■ After using blowers or other equipment, clean up!
Dispose of debris in trash receptacles.
MAINTENANCE
WARNING
When servicing, use only identical Homelite
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING
Always wear safety goggles or safety glasses
with side shields during power tool operation
or when blowing dust. If operation is dusty,
also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, z, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleumbased products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further lubrication is required.
960725012-01.indd 12
960725012-01.indd 12
NL
SV
DA
NO
FI
HU CS RU
English (original instructions)
CLEANING THE AIR FILTER SCREEN (Fig. 6)
SPARK ARRESTOR
The silencer is equipped with a spark arrestor screen
inside silencer body. After extended use the screen can
become dirty and may need to have the silencer replaced
by an authorized servicing dealer.
C L E A N I N G T H E E X H A U S T P O R T A N D
SILENCER
Depending on the type of fuel used, the type and amount
of oil used, and/or your operating conditions, the exhaust
port and silencer may become blocked with carbon
deposits. If you notice low power from the blower, have
a qualified service technician check the exhaust port
and silencer for carbon deposits. Removing the carbon
deposits should restore performance to the blower.
FUEL CAP
SPARK PLUG
This engine uses a Champion RCJ-6Y and Torch L7RTC
with 0.63 mm (0.025 in.) electrode gap. Use an exact
replacement and replace annually.
STORAGE (1 MONTH OR LONGER)
■
■
■
12
RO PL
SL
HR ET
WARNING
Never run the blower without the spark arrestor
in place. Failure to do so could result in a fire that
could cause serious personal injury.
WARNING
A leaking fuel cap is a fire hazard and must be
replaced immediately. Failure to do so could result
in a fire that could cause serious personal injury.
WARNING
Be careful not to cross-thread the spark plug.
Cross-threading will seriously damage the
product.
Drain all fuel from the tank into a container approved
for gasoline. Run engine until it stops.
Clean all foreign material from the blower. Store it in
a well-ventilated place that is inaccessible to children.
Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Abide by all Federal and local regulations for the safe
storage and handling of petrol. Excess fuel should be
used up in other 2-stroke engine powered equipment.
LT
LV
SK BG
14/02/2011 10:35 AM
14/02/2011 10:35 AM
Advertisement
