Related Manuals for Husqvarna ES020
Summary of Contents for Husqvarna ES020
- Page 1 Husqvarna Outdoor Products Italia SpA Via Como 72 23868 Valmadrera (Lecco) ITALIA Phone + 39 0341 203111 - Fax +39 0341 581671 PN. 249754 REV. 00 (09/05)
- Page 2 85°- 90° 60° 30°- 35°...
- Page 3 17 18 A A A 21 22 21 22...
-
Page 4: General Description
A. GENERAL DESCRIPTION Rear handle Cutting depth gauge Rear hand guard Cutting tooth Front handle Front hand guard/chain brake lever Chain cover Chain tensioner screw/ring Pinion Chain tensioner pin Chain catcher Oil tank cap Bar retaining screws Oil tank inspection gauge Bar retaining nut/ knob Air vents Nose sprocket... -
Page 5: Safety Precautions
B. SAFETY PRECAUTIONS MEANING OF SYMBOLS Do not dispose inappropriately Warning! of the machine. Deliver it to an Read the authorized instruction organization. manual Always grip the carefully machine with two hands Protective boots Kickback Protective danger goggles or visor, protective Do not expose helmet and to rain or... - Page 6 reference number of the corresponding component to Where necessary, all other machine parts must be draw the reader’s attention to the main safety replaced exclusively by an Authorised Service procedure linked with that particular situation; the Centre. All danger risks increase considerably if machine parts shown in “A –...
- Page 7 6. Health precautions – Chemical agents. Avoid all 11. Work operations chain oil contact with skin and eyes. Never start work with the machine before performing the following: remove the giude bar 7. Health precautions - Electricity. All extension cover guard; make sure that a sufficient amount of oil cords, plugs, and electricity lines must be has reached the chain;...
-
Page 8: Switch Block
sure that the cable/ extension cord is kept behind the 13. Precautions against fire risk. Never use the user, controlling that it does not create a source of machine in areas where there are naked flames, danger for the user or for other persons, and check inflammable or potentially explosive materials. -
Page 9: Chain Catcher
Assembly methods change according to the type of your machine- so please take care to refer to the illustrations and machine type marked on the label (A- Legend – 9 [ES020 / ES021] ), Take great care when assembling to ensure this is performed correctly. - Page 10 new; after the first assembly, the chain tension must be controlled after 5 minutes machine operation); in any case do not tighten the chain immediately after use, but wait until it cools down. In cases where the loosened chain needs to be adjusted, always unscrew the bar retaining nut/ knob before adjusting the chain tensioner screw/ring;...
- Page 11 Clean the air vents regularly to prevent motor gauge(fig.11). The difference between these determines overheating. the cutting depth; a file guide and a 4mm diameter round Check that the switch and switch block function file are needed to obtain good sharpening results; Follow correctly (to be performed with the chain brake the instructions below: Once the chain has been released): press the switch and the switch block and...
- Page 12 necessary for controlling the machine. Great care Tree felling. must be taken not to loose control . ATTENTION! : Never attempt to fell a tree if you do not have the necessary experience, and in any case Below is a description of two different types of cutting never fell trees that have trunks with a diameter larger operation: than the length of the bar ! This operation is reserved...
-
Page 13: Environmental Information
The felling cut that provokes the tree fall, is performed When cutting operations are completed the tree will at 3 to 5 cm above the lower part of the directional begin to fall. Where necessary help tree fall using felling cut line, finishing at a distance of 1/10 of the wedges or felling levers trunk from the notch. -
Page 14: Troubleshooting Table
M. TROUBLESHOOTING TABLE Motor does Motor turns The machine Motor turns Braking not start with difficulty starts but improperly or devices do or loses does not cut at reduced not stop the power properly speeds chain properly Make sure the main line is powered Make sure the machine is properly plugged in... -
Page 15: Declaration Of Conformity
The undersigned, authorized by Husqvarna Outdoor Products Italia SpA, declares that the following products model: type ES020, ES021 starting from 2005 onwards, manufactured by Husqvarna Outdoor Products Italia SpA, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) &...