Related Manuals for MBM 4107
Summary of Contents for MBM 4107
- Page 1 MBM Ideal 4107/4109 Paper Shredder Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 Operating Instructions IDEAL 4107 IDEAL 4107 CC IDEAL 4109 IDEAL 4109 CC...
- Page 3 IDEAL 4107; IDEAL 4109...
-
Page 4: Table Of Contents
For short breaks: ......... 8 For longer breaks: ........8 3.5 Oiling the shredding mechanism ....9 3.6 Replacing the plastic bag (IDEAL 4107) ..9 3.7 Operation of baler (IDEAL 4109) ....10 Bale ejection ..........10 3.8 Premature ejecting of bale (IDEAL 4109) .. 14 3.9 Central lubrication (IDEAL 4109) .... -
Page 5: General
IDEAL 4107; IDEAL 4109 1. General This instruction manual will help you to learn the safe and comfortable operation of this machine. Please carefully read and observe the operating instructions and safety instructions. This information applies to both models when no reference is made. -
Page 6: Installation
The machine is mobile on castors. The machine must be installed on a sturdy, dry, and level floor. Oil level must be visible in the sight glass (2) IDEAL 4109 version. Danger! - The machine may not be installed outside. -
Page 7: Power Supply
IDEAL 4107; IDEAL 4109 2.2 Power supply The name plate is located at the rear of the machine. - Data stated on the name plate - Voltage “ V “, - Frequency “Hz”, - Power consumption “A” must correspond to the values of the power supply unit. -
Page 8: Operation
The shredding mechanism may cause serious injury! Danger! The machine will only run when the door is closed. 3.1 Operating elements IDEAL 4107 (1) Start (2) Stop (3) Reverse switch and lamp showing “bag full“ (4) Key switch (5) Standby... -
Page 9: Machine Stops Due To Overloading
IDEAL 4107; IDEAL 4109 Machine stops due to overloading - Remove any paper left on the conveyor belt. Do not reach behind the flap. - Press and release the yellow key (3) Conveyor belt reverses. - Feed less paper onto the conveyor belt. -
Page 10: Oiling The Shredding Mechanism
- If tank (8) is empty refill with oil. Type of oil: cutting head oil 3.6 Replacing the plastic bag (IDEAL 4107) Replace bag when “bag full“ indicator lights. - Open the door (9). - Pull out the plastic bag holding the bottom of the bag. -
Page 11: Operation Of Baler (Ideal 4109)
IDEAL 4107; IDEAL 4109 3.7 Operation of baler (IDEAL 4109) Eject bale when the white control lamp shows Danger! Do not stand behind the bale ejecting guard during baling. Danger of being crushed. Bale ejection - Release safety slide (1). - Page 12 - Hold bale ejecting guard (2) with the left hand and swing locking mechanism (4) with the right hand into vertical positon ..until securing bushing (5) locks into position. - Swing down bale ejecting guard (2). - Press green button (6) until the pump motor switches off.
- Page 13 IDEAL 4107; IDEAL 4109 - While removing the plastic bag push down the remaining paper. - Place pressed bale on the floor. Danger! Do not reach into the hopper. Danger of getting cut! - Tie bales or seal with locking device. (for sealing parts and binding wires see accessories).
- Page 14 Close bale - Push up locking bush (5) and swing down locking mechanism (4). - Slightly open the bale ejecting guard (2) with both hands until the lug (14) is above the locking catch (15). - Hold bale ejecting guard with the left hand. Swing locking lever (2) with the right hand until it is almost in horizontal position and after locking into catch return it to the original position.
-
Page 15: Premature Ejecting Of Bale (Ideal 4109)
IDEAL 4107; IDEAL 4109 - Important! Lock safety slide (1). (Pull back and turn up.). 3.8 Premature ejecting of bale (IDEAL 4109) - Push knob (16) with pen or similar. - Further procedure as described in 3.7 “Operation of baler“. -
Page 16: Trouble-Shooting
- Machine is plugged in - On-site fuse - Machine is overloaded - The motor protection switch releases the machine after approx. 2 min. - Central lubrication IDEAL 4109 Malfunction: Motor hums and has no power. Cause: One phase is missing. -
Page 17: Accessories
IDEAL 4107; IDEAL 4109 5. Accessories Plastic bags 350 l (50 pieces) 9000412 Cutting head oil 10 x 0,2 l 9000610 For fastening plastic bags: Wire twisting tool for one-way plastic bags 9000591 Wire ties for one-way plastic bags (1000 pieces) -
Page 18: Ec-Declaration Of Conformity
- Si dichiara che il modello della - Hiermede verklaren wij, dat de in de handel gebrachte machine - Com a presente, declaramos que o modelo da - Hermed erklæres, at produkttypen 4107; 4107 CC; 6040 S; 6040 C 4109; 4109 CC;... - Page 19 IDEAL 4107; IDEAL 4109 IDEAL Krug & Priester 72336 Balingen Germany www.ideal.de...
Need help?
Do you have a question about the 4107 and is the answer not in the manual?
Questions and answers