Makita BUH550 Instruction Manual
Cordless hedge trimmer
Hide thumbs
Also See for BUH550:
- User manual ,
- Instruction manual (81 pages) ,
- Technical information (9 pages)
Related Manuals for Makita BUH550
Summary of Contents for Makita BUH550
- Page 1 INSTRUCTION MANUAL Cordless Hedge Trimmer BUH550 BUH650 UH550D UH650D 011146 IMPORTANT: Read Before Using.
-
Page 2: Specifications
Read instruction manual. The vibration total value (tri-axial vector sum) determined according to EN60745: ･ Do not expose to rain. Model BUH550,UH550D ･ Only for EU countries Ni-MH Work mode : impact tightening of fasteners of the Do not dispose of electric equipment or... -
Page 3: General Power Tool Safety Warnings
EC Declaration of Conformity Warnings Makita Corporation responsible manufacturer declare that the following Makita WARNING Read all safety warnings and all machine(s): instructions. Failure to follow the warnings and Designation of Machine: instructions may result in electric shock, fire and/or Cordless Hedge Trimmer serious injury. - Page 4 Personal safety dangerous in the hands of untrained users. 10. Stay alert, watch what you are doing and use 21. Maintain power tools. Check for misalignment common sense when operating a power tool. or binding of moving parts, breakage of parts Do not use a power tool while you are tired or and any other condition that may affect the under the influence of drugs, alcohol or...
- Page 5 GEB062-3 guards are fitted properly. The hedge trimmer must not be used unless fully assembled. CORDLESS HEDGE TRIMMER 12. Make sure you have a secure footing before SAFETY WARNINGS starting operation. 13. Hold the tool firmly when using the tool. Hold the power tool by insulated gripping 14.
-
Page 6: Functional Description
ENC007-6 FUNCTIONAL DESCRIPTION IMPORTANT SAFETY INSTRUCTIONS CAUTION: Always be sure that the tool is switched off and the • FOR BATTERY CARTRIDGE battery cartridge is removed before adjusting or Before using battery cartridge, read all checking function on the tool. instructions and cautionary markings on (1) Installing or removing battery cartridge battery charger, (2) battery, and (3) product... -
Page 7: Speed Change
Handle mounting positions Speed change 1. Adjusting dial 011233 The strokes per minute can be adjusted just by turning the adjusting dial. This can be done even while the tool is running. The dial is marked 1 (lowest speed) to 6 (full speed). - Page 8 Contact your local Makita When charging a battery cartridge, first remove it • authorized service center. from the battery adapter and then charge it. It is not allowed to charge the battery cartridge while using NOTE: battery adapter.
-
Page 9: Operation
To insert the battery adapter, align the tongue on • NOTE: the battery adapter with the groove in the housing Do not pass the extension cord through the band. • and slip it into place. Always insert it all the way Do not force the opening of the holder. - Page 10 of 3 - 4 seconds per meter. Installing or removing chip receiver (accessory) 1. String CAUTION: Always be sure that the tool is switched off and the • battery cartridge is removed before installing or removing chip receiver. NOTE: When replacing the chip receiver, always wear •...
-
Page 11: Maintenance
Removing or installing shear blade 1. Press the hooks on both sides CAUTION: 2. Unlock the Before removing or installing shear blade, always • hooks be sure that the tool is switched off and the battery cartridge is removed. When replacing the shear blade, always wear •... - Page 12 Set the crank at the angle as shown in the figure with a slotted bit screwdriver. 1. Oval hole of 1. Crank shear blade 011259 Take out the blade cover from the old shear blades and fit 011256 Remove two screws from the shear blades and the shear it onto the new ones for easy handling during the blade unit will be taken out.
-
Page 13: Replacing Carbon Brushes
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 1. Brush holder Blade cover •... - Page 14 NOTE: Some items in the list may be included in the tool • package as standard accessories. They may differ from country to country.
- Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 884974B227...