Advertisement
Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
Board Input Test
IN
While in Service Mode, pressing the
Spin Only key will begin the Board Input
Test. This test turns on a specified output
after a key press. Pressing the Spin Only key again
cancels the test. (Display shows "in").
While in Service Mode follow chart to check respective
function.
•
When the Rotary Cycle Selector knob is set to
"Super Wash" and the Rotary Cycle Selector knob
is pressed, the door position will be displayed: "0P" if
open, "CL" if closed.
•
When the Rotary Cycle Selector knob is set to
"Normal" and the Rotary Cycle Selector knob is
pressed, the Lock position will be displayed: "UL" if
unlocked, "L0" if locked.
•
When the Rotary Cycle Selector knob is set to
"Whites" and the Rotary Cycle Selector knob is
pressed, the High water level will be displayed: "
–
if below level, "
1" if above level. The High water
level is defined as the over flow water level.
•
When the Rotary Cycle Selector knob is set to
"Wrinkle Control" and the Rotary Cycle Selector
knob is pressed, the Medium water level will be
displayed: "—0" if below level, "—1" if above level.
The Medium water level is defined as the minimum
water level needed such that the heater can be
turned 'ON' (only MAH8700* and MAH9700* models
have heaters).
•
When the Rotary Cycle Selector knob is set to
"Colors" and the Rotary Cycle Selector knob is
pressed, the Low water level will be displayed: "_0" if
below level, "_1" if above level. The Low water level
is defined as the reset water level.
•
When the Rotary Cycle Selector knob is set to
"Hand Wash" and the Rotary Cycle Selector knob
is pressed, the level of Tub unbalance will be
displayed: "UC" if balanced, "U0" if unbalanced. "U0"
will be displayed during the time when the machine
is correcting for the unbalance; e.g. slowing down to
redistribute the load or to get to a lower spin speed.
Once the situation has been corrected (i.e. the load
has begun tumbling or the lower speed has resulted
in an acceptable amount of balance); "UC" will once
again be displayed.
•
When the Delay key is pressed, the water
temperature will be displayed in Degrees F
(Fahrenheit).
•
When the Rotary Cycle Selector knob is set to
"Delicates" and the Rotary Cycle Selector knob is
pressed, the water temperature will be displayed in
degrees C (Celsius).
June 2006
©2006 Maytag Services
!
WARNING
•
When the Rotary Cycle Selector knob is set to
"Sanitary", and the Rotary Cycle Selector knob is
pressed, the water level frequency will be displayed.
"2560" means 25.60 Hz (washer empty). Frequency
value drops as water rises.
While performing the Board Input Test in Service
Mode, follow this quick reference chart to check
respective functions.
Selection
Rotary Cycle
Selector set to
"Super Wash".
Press Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Normal". Press
Rotary Cycle
–
0"
Selector.
Rotary Cycle
Selector set to
"Whites". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Wrinkle Control".
Press Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Colors". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Hand Wash".
Press Rotary Cycle
Selector.
Press Delay key.
Rotary Cycle
Selector set to
"Delicates". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Sanitary". Press
Rotary Cycle
Selector.
9
Function
Display
Door position
"0P" or "CL"
Lock state
"UL" or "L0"
–
"
0" if below
High water
level. "
level
above level.
"
"
if below
—0
Medium water
level. "—1" if
level
above level.
"_0" if below
Low water level
level. "_1" if
above level.
"UC" if
Tub balance
Balanced. "U0"
if Unbalanced
Water
Degrees F
temperature
Water
Degrees C
temperature
"2560" (empty).
Water Level
Frequency
Frequency(Hz)
drops as water
rises.
16026736
–
1" if
Hide quick links:
Advertisement
