Delta CL180 Instruction Manual

Cordless drill/driver and charger

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Cordless Drill/Driver and

Charger

(Model CL180)

Battery Model

Charger Model

CL180B

CL180C

PART NO. 906994 - 07-15-03

To learn more about DELTA MACHINERY

ESPAÑOL: PÁGINA 14

visit our website at: www.deltamachinery.com.

For Parts, Service, Warranty or other Assistance,

1-800-223-7278 (

1-800-463-3582).

please call

In Canada call

Table of Contents

Summary of Contents for Delta CL180

Page 1 Battery Model Charger Model CL180B CL180C PART NO. 906994 - 07-15-03 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY ESPAÑOL: PÁGINA 14 visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582).
Page 2: Safety Guidelines - Definitions
SAFETY GUIDELINES / DEFINITIONS This manual contains information that is important for you to know and un- derstand. This information relates to protecting YOUR SAFETY and PRE- VENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols listed below. Please read the manual and pay attention to these sections.
Page 3: Personal Safety
Use battery operated tool only with specifically designated battery pack. Use of any other batteries may create a risk of fire. PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.
Page 4: Specific Safety Rules And Symbols
Request, and follow, all safety information available from your material supplier. There are certain applications for which this tool was designed. Delta strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written Delta and we have advised you.
Page 5: Safety Instructions For Charger And Batteries
To reduce risk of injury, a Delta ShopMaster charger should only be used to charge a Delta ShopMaster battery pack. Other types of bat- teries may burst causing personal injury and damage. Do not charge a Delta ShopMaster battery pack with any other charger.
Page 6: Functional Description
RBRC ™ . For further information, call: 1-800-8-BATTERY. FUNCTIONAL DESCRIPTION FOREWORD Your Delta ShopMaster Drill/Driver is designed to drill holes and drive fasten- ers in various materials as indicated in the following chart: MAXIMUM CAPACITIES DRILLING DRIVING...
Page 7 FORWARD/REVERSE • Make sure trigger switch (A) Fig. 1, is in OFF position before attempt- ing to change direction of rotation. • Push button (B) Fig. 1, toward left side of drill for FORWARD (clock- wise) rotation. • Push button (B) Fig. 1, toward right side of drill for REVERSE (counterclock-wise) rotation.
Page 8: Operation
TWO-SPEED GEAR SHIFT HIGH The Model CL144 Cordless Drill/ Driver has a two-speed gear shift which provides spindle speed 0-350 0-1300 ranges as shown in Fig. 3A. To Fig. 3A change speed ranges: release trig- ger switch to stop motor and then slide speed selector (A) Fig.
Page 9 Depending on room temperature, line voltage, and existing charge level, ini- tial battery charging may take longer than one hour. Disconnect charger from power source when not in use. Special Charge Modes: If all lights go out after the battery is inserted, the charger has entered pre-charge mode.
Page 10: Drilling Wood
Set REVERSING BUTTON for clockwise rotation. Make sure work is held securely in vise or clamped in place prior to starting drilling operation. Loose work may spin and cause bodily injury. Locate exact center for hole to be drilled and using a center punch, make a small dent in work.
Page 11 DRIVING WOOD SCREWS Drill pilot and shank clearance holes. See following chart: ↑ SUGGESTED HOLE SIZES FOR WOOD SCREWS Shank Pilot Drill Diameter Drill Shank Drill ↓ Screw Clearance Soft Hard Size Diameter Wood Wood ↑ (.140) (.062) (.109) (.172) (.078) (.125) Pilot...
Page 12: Maintenance
LUBRICATION For your continued safety and electrical protection, lubrication and service on this tool should ONLY be performed by an AUTHORIZED DELTA SERVICE STATION or a DELTA SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest Authorized Delta Service Station to be thoroughly cleaned and inspected;...
Page 13: Parts, Service Or Warranty Assistance
223-7278 (In Canada call 1-800-463-3582). Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the...
Page 14 ACCESORIOS Una línea completa de accesorios está disponible de su surtidor de Porter- Cable · Delta, centros de servicio de la fábrica de Porter-Cable · Delta, y esta- ciones autorizadas delta. Visite por favor nuestro Web site www.deltama- chinery.com para un catálogo o para el nombre de su surtidor más cercano.
Page 15 Porter-Cable • Delta products should be obtained by contacting any Porter-Cable • Delta Distributor, Authorized Service Center, or Porter-Cable • Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the near- est Porter-Cable •...