Advertisement
INTRODUCTION
Thank you for purchasing this
Lec appliance that has been made
from the very best materials
available
and
has
been
extensively tested and inspected
before leaving our factory. This
Bottle
Cooler
has
been
specifically
designed
to
store
bottled and canned drinks and
when properly installed and cared
for, will give years of good
service.
UNPACKING
Please
remove
all
internal
packing.
When
unpacked
complete the appliance should
stand for 2 hours to allow coolant
to settle.
POSITIONING
In order to conserve electricity do
not put your appliance near a
source
of
heat,
such
as
radiator. Try to avoid locations
where the sun shining through
glass
can
raise
the
room
temperature.
An unheated location such as a
cellar is undesirable as it may
cause frost build up and slow
defrosting. It may also cause
excessive condensation on the
outer surface of your cabinet.
INSTALLATION
It is important to note that the
appliance
can
be
installed
built-in, without air gaps as the
appliance has been designed to
gain ventilation from the front.
The air ventilation at the bottom
of
the
cabinet
must
unobstructed
to
allow
circulate around the cabinet. The
Bottle Cooler is also fitted with
adjustable feet on the front. If the
cabinet is placed on an uneven
surface
this
can
misalignment of the cabinet and
doors. The feet must be adjusted
so that the cabinet stands firm
and level, with a slight tilt from
front to back to prevent any
is
defrost water dripping from the
front. The cabinet should be
placed on a hard flat surface for
ventilation.
WHAT TO DO BEFORE
STARTING
a
Clean
the
interior
of
appliance
(See
the
"Cleaning your Appliance").
1
SAFETY AND SERVICING
THIS
EARTHED
If this appliance is fitted
with
for
which
unsuitable the plug should
be
be
appropriate
air
to
The
removed
disposed of as insertion of
the plug into an electrical
socket
dangerous.
cause
ELECTRIC PLUG WIRING (UK
ONLY)
The wires in the mains lead are
coloured in accordance with the
following code:
GREEN AND YELLOW - EARTH
your
section
As the colours of the wires in the
mains lead of your appliance may
not correspond with the coloured
marking identifying the terminals
in your plug, proceed as follows:
CONNECT
coloured wire to plug terminal
marked 'E' or earth symbol
coloured green or green and
yellow.
APPLIANCE
MUST
BE
CONNECT BLUE coloured wire to
plug
coloured black.
a
non-rewirable
plug
CONNECT BROWN coloured wire
your
socket
is
to plug terminal marked 'L' or
cut
off
and
an
coloured red.
plug
fitted.
plug
must
be
Do not push excess mains lead
into the compressor
compartment.
is
likely
to
be
If it is necessary to change the
fuse in a moulded plug and the
fuse cover is detachable, it must
be refitted after the fuse has
been changed. If the fuse cover is
lost or damaged the plug must
not be used until a replacement
is obtained.
BLUE - NEUTRAL
It is important that the colour of
BROWN - LIVE
the
corresponds with the coloured
insert
embossed words on the base of
the
covers are available from the
Spares
Refrigeration plc. at the address
on the rear cover of this leaflet.
When a non-rewirable plug or a
rewirable 13 Amp (BS 1363) plug
is used it must be fitted with a
13 Amp ASTA approved (BS 1362)
fuse. If any other type of plug is
used it must be protected by a 15
Amp fuse either in the plug or at
the distribution board.
GREEN
&
YELLOW
2
or
terminal
marked
'N'
or
replacement
fuse
cover
or
as
indicated
in
plug.
Replacement
fuse
Department,
Lec
Advertisement
