Blue Seal Evolution series G47 Installation And Operation Manual
Gas pasta cooker evolution series
Hide thumbs
Also See for Evolution series G47:
- Installation and operation manual (25 pages) ,
- Service manual (38 pages)
Related Manuals for Blue Seal Evolution series G47
Summary of Contents for Blue Seal Evolution series G47
- Page 1 I N S T A L L A T I O N A N D O P E R A T I O N M A N U A L GAS PASTA COOKER G 4 7 232425-5...
- Page 2 (tel): 800 263 1455 (Toll Free) NEW ZEALAND Moffat Limited Web: www.moffat.co.nz E.Mail: sales@moffat.co.nz Main Office: (tel): 0800 663328 UNITED KINGDOM Blue Seal Web: www.blue-seal.co.uk E.Mail: sales@blue-seal.co.uk Sales: (tel): +44 121 327 5575 (fax): +44 121 327 9711 Spares: (tel): +44 121 322 6640...
-
Page 3: Table Of Contents
Contents GAS PASTA COOKER - (Single Tank - 40 Ltr) Introduction .................... 2 Specifications ..................3 Model Numbers Covered in this Specification General Optional Accessories Gas Supply Requirements Gas Connection Water Supply Requirements Dimensions ....................5 Installation ....................6 Installation Requirements Unpacking Location Clearances... -
Page 4: Introduction
Introduction We are confident that you will be delighted with your BLUE SEAL Pasta Cooker and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new BLUE SEAL Appliance, there are two important things you can do. -
Page 5: Specifications
Specifications Model Numbers Covered in this Specification PASTA COOKER (Single Tank - 40 Ltr). General A commercial heavy duty, gas fired high performance Pasta Cooker designed for pasta cooking commercial high production output, using LPG (Propane) or Natural Gas. The boiling medium is contained within a heavy gauge stainless steel tank, heated by one infra red surface burner from beneath the tank. -
Page 6: Gas Connection
Specifications Gas Connection Gas supply connection point is located 152 mm from the left hand side, 33 mm from the rear of the appliance and 152 mm from the floor and is entered from beneath the appliance. An optional rear connection is available. -
Page 7: Dimensions
Dimensions G47-Pasta Cooker... -
Page 8: Installation
Blue Seal pasta cookers are designed to provide years of satisfactory service and correct installation is essential to achieve the best performance, efficiency and trouble-free operation. -
Page 9: Location
Gas Connection NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A QUALIFIED SERVICE PERSON. Blue Seal Pasta Cookers do not require an electrical connection, they function totally on the gas supply only. It is essential that the gas supply is correct for the appliance to be installed and that adequate supply pressure and volume are available. -
Page 10: Location
Installation Fit the gas regulator supplied, into the gas supply line as close to the appliance as possible. The regulator connections are " BSP female. The connection to the appliance is " BSP male. (Refer to the 'Specifications' section for the gas supply location dimensions). NOTE: A Manual Isolation Valve must be fitted to the individual appliance supply line. -
Page 11: Water Connection
Installation Water Connection NOTE: The water connection shall be installed in accordance with local water regulations in force and the applicable standard / code, e.g. PCA in Australia. A cold water supply must be connected to the water inlet connection (R "... -
Page 12: Operation
/ operator. Blue Seal 'Pasta Cookers have been designed to provide simplicity of operation and 100% safety protection. Improper operation is therefore almost impossible, however bad operation practices can produce a poor quality product. -
Page 13: Before Use
Operation WARNING: REAT CARE MUST BE TAKEN BY THE OPERATOR TO USE THE PASTA COOKER SAFELY TO GUARD AGAINST THE RISK OF INJURY AND FIRE • DO NOT LEAVE THE PASTA COOKER UNATTENDED DURING OPERATION • DO NOT OVER FILL THE WATER IN THE PASTA COOKER ABOVE THE UPPER FILL LEVEL MARK •... -
Page 14: Lighting The Pilot Burner
Operation Lighting the Pilot Burner AUTIO N Do NOT ignite the burner if the tank is empty (No Water). Ensure that the tank is filled to the correct level before igniting the main burner. With the pasta cooker tank full of water, the pilot burner can be lit. Check that the gas supply is turned on at the mains supply. -
Page 15: Cleaning And Maintenance
Cleaning and Maintenance WARNING: DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO THE PASTA COOKER HOT. WHILST THE COOKER IS STILL AUTIO N Always turn off the gas supply at the mains supply before cleaning. This appliance is not water proof. -
Page 16: After Each Use
Cleaning and Maintenance Locking Slide Locking Slide Fig 6 Fig 5 After Each Use WARNING: OT WATER WILL SCALD DO NOT RUSH THIS JOB Clean the interior of the pan regularly after each use. Do not use wire brushes on the pan. Clean using a mild detergent and a hot water solution using soft cloth or a soft bristled brush. -
Page 17: Weekly Cleaning
Cleaning and Maintenance Weekly Cleaning WARNING: O NOT ATTEMPT TO MOVE THE ASTA OOKER WHILST THE COOKER IS FULL OF WATER EFORE ATTEMPTING TO MOVE THE ASTA OOKER ENSURE THAT ALL THE WATER HAS BEEN DRAINED FROM THE TANK EFER TO THE INFORMATION ON THE PREVIOUS PAGE ON HOW TO DRAIN THE WATER FROM THE ASTA OOKER... -
Page 18: Fault Finding
Fault Finding This section provides an easy reference guide to the more common problems that may occur during the operation of your equipment. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section. -
Page 19: Wiring Schematic
Wiring Schematic G47 Pasta Cooker... -
Page 20: Gas Conversion And Specifications
Gas Conversion and Specifications Conversion Procedure AUTIO N Ensure the unit is isolated from the gas supply before commencing servicing. NOTE: • These conversions should only be carried out by qualified service persons. connections must be checked for leaks before re-commissioning the appliance. •... - Page 21 Gas Conversion and Specifications Low Fire Adjustment a. To adjust the burner low fire adjustment, adjust the Low Fire low fire adjustment screw on the open burner gas Adjusting Screw control valves to obtain the desired flame size. NOTE: The 'Low Fire Screw' should be sealed with coloured paint on completion of low fire adjustment.
-
Page 22: Gas Specifications
Gas Conversion and Specifications Gas Type Identification Label On completion of the gas conversion, replace the gas type identification label located at:- - The rear of the appliance, above the gas connection. - Beside the rating plate. Commissioning Before leaving the converted installation; Check all gas connections for leakages using soapy water or other gas detecting equipment. -
Page 23: Replacement Parts List
Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on reverse of front cover of this manual). - Page 24 Replacement Parts List Gas Conversion Kit Gas Type to Convert to Model Nat. Gas Butane Town Gas 232061 232060 232062 N/A (*) NOTE: (**) Town Gas Option is only available with specific ex-factory built Town Gas models, which can also be converted to any other gas. Standard models can only be converted between Nat.
Need help?
Do you have a question about the Evolution series G47 and is the answer not in the manual?
Questions and answers