Advertisement

Quick Links

MODEL 5802
owner
s manual
'

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Slash 5802 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Traxxas Slash 5802

  • Page 1 MODEL 5802 owner s manual ’...
  • Page 2 THE SLASH and running in the shortest time possible. If you are an the turns. The Traxxas Slash hangs it out for an all new way to experienced R/C enthusiast you will find it helpful and fast. challenge your driving skills. The 4-wheel independent suspension...
  • Page 3: Before You Proceed

    SAFETY PRECAUTIONS Traxxas materials to prevent serious damage to your model. Failure to follow All of us at Traxxas want you to safely enjoy your new model. Operate 1100 Klein Road these instructions will be considered abuse and/or neglect. your model sensibly and with care, and it will be exciting, safe, and fun Plano, Texas 75074 for you and those around you.
  • Page 4 Using a schottky diode with the XL-5 of the installation and/or use of LiPo batteries in Traxxas products. will damage the ESC and void the 30-day warranty.
  • Page 5: Tools, Supplies And Required Equipment

    For more information, see Use the Right Charger on page 10. NiMH battery charger NiMH 7.2V to 8.4V 6 or 7-cell battery pack 8 AA alkaline (peak detecting type recommended) with Traxxas High-Current Connector batteries SLASH • 5...
  • Page 6 ANATOMY OF THE SLASH Steering Block Front Shock Tower Traxxas High- Turnbuckle Current Connector (Rear Camber Link) Steering Servo Electronic Speed Caster Block Suspension Arm (Rear) Battery Control (XL-5) Compartment Slipper Clutch Suspension (under gear cover) Nerf Bar Arm (Front)
  • Page 7: Quick Start: Getting Up To Speed

    QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. The Quick Start Guide is not intended to replace the 1.
  • Page 8: Applying The Decals

    DECORATING YOUR MODEL APPLYING THE DECALS TIRE GLUING The main decals for your model have The factory tires on your model are been applied at the factory. The decals already glued to the rims. The tires are printed on self-adhesive clear mylar must be glued to the rims to prevent and are die-cut for easy removal.
  • Page 9: Wiring Diagram

    Your model is equipped with the Traxxas TQ Radio System. XL-5 Wiring Diagram WIRING DIAGRAM The Traxxas TQ Radio System is a 2-channel system that provides Motor high-power output up to a quarter mile. Your model uses one servo Antenna (Titan ®...
  • Page 10 Frequency band - The radio frequency used by the transmitter to send between two points, such as between the positive battery terminal signals to your model. All Traxxas RTR models operate on a 27 MHz and ground. Using the analogy of the garden hose, while current is the frequency band.
  • Page 11: Installing Transmitter Batteries

    XL-5. The Traxxas connector’s gold-plated terminals with a large contact surfaces ensure positive current flow with the least amount of resistance. Secure, long-lasting, and easy to grip, the Traxxas connector is engineered to extract all the power your battery has to give.
  • Page 12 THE TRAXXAS TQ RADIO SYSTEM SETTING UP THE ANTENNA TQ RADIO SYSTEM CONTROLS You must install the antenna mast (tube) Spray a little window cleaner before you operate your model. You’ll on the antenna wire to make Antenna find the assembled plastic antenna tube...
  • Page 13 THE TRAXXAS TQ RADIO SYSTEM Electronic Throttle Trim The electronic throttle trim located on the face of the transmitter adjusts the neutral (center) point of the throttle servo when the servo is at rest. Your model uses an electronic speed control instead of a throttle servo, this control has been preset for you at the factory.
  • Page 14 THE TRAXXAS TQ RADIO SYSTEM TQ RADIO SYSTEM RULES 3. Plug the battery pack in the model into the speed control. Channel 1 Each time you prepare to run your model, you Brown 4. The on/off switch is integrated into the speed control. With the...
  • Page 15: Adjusting Electronic Speed Control

    ADJUSTING THE ELECTRONIC SPEED CONTROL XL-5 Battery Settings (Low-Voltage Detection Setting) XL-5 Setup Programming (Calibrating your ESC and transmitter) The XL-5 electronic speed control is equipped with built-in Low-Voltage Read through all of the programming steps before you begin. If you get lost XL-5 Specifications Detection.
  • Page 16 ADJUSTING THE ELECTRONIC SPEED CONTROL avoid slamming the speed control from reverse to forward. On high-traction Selecting Training Mode (Profile #3: 50% Forward, 100% Brakes, 50% Reverse) surfaces, this could result in transmission or driveline damage. 1. Turn on your transmitter and connect a fully Patent-Pending Training Mode 7.
  • Page 17: Driving Your Model

    Running in grass and off-road could cause • The Traxxas TQ transmitter is not water resistant. Do not subject it to wet excessive loads on the electrical system in the model.
  • Page 18 Label which wire is for which channel. 4. Blow off the truck with compressed air (optional, but recommended). Wear 4. Apply small bead of silicone grease (Traxxas part #1647) safety glasses when using compressed air. to the wire clamp (B).
  • Page 19: Adjusting Your Model

    -1.5 -1.5 ° ° ° ° ADJUSTING YOUR MODEL Once you become familiar with driving your model, you might the two-hole pistons with a range of oil viscosities from 10W to 50W (available from need to make adjustments for better driving performance All of the toe links are installed your hobby shop).
  • Page 20 ADJUSTING YOUR MODEL Adjusting the Slipper Clutch extremely hot, and/or the motor is too hot to touch, your model is The model is equipped with an probably over-geared. If you are not able to run your model for at least To achieve a good starting adjustable slipper clutch which four minutes before the battery dies, then change to a lower gear...
  • Page 21 ADJUSTING YOUR MODEL Adjusting Gear Mesh Incorrect gear mesh is the most common cause of stripped spur gears. Gear mesh should be checked and adjusted anytime a gear is replaced. To set the gear mesh, cut a narrow strip Strip of Paper of notebook paper and run it into the gear mesh.
  • Page 22: Maintaining Your Model

    If the bottom of the shock is leaking, then it condition of the batteries. is time for a rebuild. The Traxxas rebuild kit for two shocks is 8. Check for any loose screws in the chassis structure part #2362.
  • Page 23: Troubleshooting

    Keep stripping spur gears: and motor. Improper gear mesh, refer to “Adjusting Gear Mesh” on page 21. XL-5: Possible internal damage. Return the XL-5 to Traxxas for service. Improperly adjusted slipper clutch, refer to “Adjusting the Slipper Clutch” on page 20.
  • Page 24 MODEL 5802 owner s manual ’ 1100 Klein Road, Plano Texas 75074 1-888-TRAXXAS 100923 KC1333 -R00...

This manual is also suitable for:

Slash 5805

Table of Contents