Advertisement

DISTRIBUTED BY: POLYGROUP LIMITED (MCO)
Avenida Xian Xing Hai, Edificio Zhu Kuan, 11 Andar M, Macau
Customer Service Representative: General Foam Plastics Corporation
ABOVE GROUND RECTANGULAR QUICK SET
System Info Label
WARNING:
people to lay over or sit on pool wall- DOING SO CAN CAUSE
PERMANENT INJURY!
DRAIN pool to the proper level after a heavy rain.
NOTE: DO NOT attempt to assemble this pool in adverse weather
conditions, windy conditions or when the temperature is below 60°F.
NOTE: This is a storable pool, which should be disassembled and
stored when temperatures are expected to fall below 32°F.
ATTENTION CUSTOMER: STATEMENT OF LIMITED WARRANTY
Polygroup Limited (MCO) warrants to the original purchaser only, the Quick Set
workmanship for 90-days from the date of purchase. Original Purchaser must retain proof of such purchase in the
form of a store sales receipt and must produce such upon request by Polygroup Limited (MCO) or its customer service
representative, General Foam Plastics Corporation at (800) 813-0206.
If the unit is found to have been consumer damaged or abused, it is not covered by the limited warranty. If this is the
case, you will be advised of the cost of replacement part(s), or the need to return damaged part(s) for warranty replace-
ment.
This limited warranty is not valid if pool is used for commercial purposes or if the damage is caused by accident, act of
God, consumer neglect or abuse, failure to properly follow disassembly and storage procedures, vandalism or improp-
er use of chemicals. This limited warranty will also be voided if pool is not properly installed per instructions. This
warranty does not hold Polygroup Limited (MCO) responsible for cost of installation, labor or transportation related
to replacement of defective parts.
(800) 813-0206 • www.POLYGROUP.com
OWNER'S MANUAL
"Splash Guard" Technology
DO NOT overfill the pool and / or allow
SWIMMING POOL
®
S
I
___________________2
AFETY
NFORMATION
C
A
B
ONSUMER
WARENESS
OOKLETS
S
P
_____________________4
ITE
REPARATION
P
I
_
_ _
_ _
OOL
NSTALLATION
D
A
S
ISASSEMBLY
ND
TORAGE
P
& A
_________________8
ARTS
CCESSORIES
P
C
S
____________________9
OOL
OVER
AFETY
N
__________________________10
OTES
Pool against defects in material and
®
_________3
_ _
_ _
_ _
_ _
_ _
_ _
_ _
4 _
_____________7
2011
084-120004

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P23-081436 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Polygroup P23-081436

  • Page 1 90-days from the date of purchase. Original Purchaser must retain proof of such purchase in the form of a store sales receipt and must produce such upon request by Polygroup Limited (MCO) or its customer service representative, General Foam Plastics Corporation at (800) 813-0206.
  • Page 2 Read and Follow All Safety Information and Instructions. Keep for Future Reference. Failure to follow these warnings and instructions can result in serious injury or death to user, especially children. WARNING DANGER PREVENT NO DIVING! DO NOT SIT ON AVOID DROWNING NO JUMPING! OR LAY OVER...
  • Page 3 13. The pool is subject to wear and deterioration. If not maintained properly, certain types of excessive or accelerated deterioration can lead to failure of the pool structure that might release large quantities of water that could cause bodily harm and property damage. 14.
  • Page 4: Pool Installation

    RECTANGULAR FRAME POOL SETUP INSTRUCTION SHEET SITE PREPARATION WARNING VERY IMPORTANT! SITE MUST BE LEVEL, STABLE, COMPACTED SOIL. • The pool must be assembled on a smooth and level site of firm soil that is free of stones, gravel, sticks, black- top or other oil base compounds.
  • Page 5 (Horizontal Beams) into the sleeve (making certain you work in a clockwise direction around the pool with all swedged parts pointing clockwise) see Fig. 1 and refer to the “View of All Frame Assembly Parts” shown on page 5. 5. Connect the (Horizontal Beams) together pushing the button in as you insert one beam into the other beams end. Look through the locking hole in the beam as you join them, slightly rotate the beams until the button aligns with the hole and pops up, locking that beams end into the other beams end.
  • Page 6 3. Now locate the (U-Shape) pipe frames. Each end of the (U-Shape) pipe will have a cap to be installed on it. Locate the pipe caps and install those, push the buttons in as you insert the cap onto the pipes end Fig. 3. Look through the holes in the cap as you in- stall it and slightly rotate the cap until the Pool Liner Sleeve...
  • Page 7: Disassembly And Storage

    DISASSEMBLY AND STORAGE 1. GENERAL INFORMATION: Pool must be stored if temperatures are expected to fall below 32°F. A. All parts should be cleaned with a mild soap and lukewarm water only - DO NOT use detergent or hot water. B.
  • Page 8 POOL SIZE PART NO. QTY WGT COST PART NO. QTY WGT COST PART NO. QTY WGT COST MODEL (LBS) (LBS) (LBS) P23-081436 8’ X 14’ X 36” 090-380058 3.26 3.00 090-380037 0.018 0.50 090-380065 3.88 7.00 090-380029 4.03 3.00 P23-091852 9’...
  • Page 9: Pool Cover Safety

    POOL COVER SAFETY IF YOU ARE GOING TO USE A POOL COVER, SOLAR COVER OR SOLAR BLANKET, PLEASE READ THIS INFORMATION. POOL COVER WARNING SOLAR BLANKET WARNING SOLAR COVER WARNING WARNING WARNING AVOID DROWNING RISK AVOID DROWNING RISK STAY OFF COVER - WILL NOT SUPPORT WEIGHT. STAY OFF COVER - WILL NOT SUPPORT WEIGHT.
  • Page 10 NOTES: Should you encounter any problems, contact the Customer Service Representative/Parts Department at (800) 813-0206 from 8 AM to 5 PM Mon. thru Fri. EST. Extended operating days and hours during peak season requirements.

Table of Contents