Page 1 AP-IP300 IP Phone Installation Guide Version 1.0 AP-IP300 IP Phone [Installation and Operation Guide] November, 2007 AddPac Technology www.addpac.com AddPac Technology Proprietary & Documentation...
Page 2 AP-IP300 IP Phone Installation Guide Version 1.0 AP-IP300 IP Phone Note. The specifications and information in this guide are subject to change without notice. All statements, information, and recommendations in this guide are believed to be accurate but are presented without warranty of any kind, express or implied.
Page 3: Table Of Contents
AP-IP300 IP Phone Installation Guide Version 1.0 [Contents] Getting into AP-IP100 IP Phone Installation Guide ............11 Chapter 1. Introduction ........ 13 Introduction ......................... 13 Product Overview ....................... 13 AP-IP300 IP Phone Hardware Specification ..............16 AP-IP300 IP Phone Software Specification............... 17 The Upper View ........................
Page 4 AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box – Factory Default....................64 Tool Box – Ring ........................65 Tool Box – Power Save....................... 67 Tool Box – Version Information ..................68 Tool Box – Language ......................69 Tool Box – Password ......................70 AV Setup Menu ........................
Page 5 AP-IP300 IP Phone Installation Guide Version 1.0 Application - Application – Remote Broadcast .............. 122 Application - Application Setup – Chime Setup............. 123 Application - Application Setup – Client Info Setup ............124 Application – Client Info....................125 Application – Remote Broadcast..................126 System Setup Menu......................
Page 6 AP-IP300 IP Phone Installation Guide Version 1.0 [Figures] (Figure 1-1) Network Diagram of AP-IP300 IP Phone (Figure 1-2) The Upper View for the Key Arrangement of AP-IP300 (Figure 1-3) The Rear Side (Figure 3-1) Connecting WAN Interface (Figure 3-2) Connecting LAN Interface...
Page 7 AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-25) Information Menu Screen (Figure 4-26) Language Menu Screen (Figure 4-27) Password Menu Screen (Figure 4-28) Main Menu (Figure 4-29) AV Setup Menu Screen (Figure 4-30) Volume Setup Menu Screen (Figure 4-31) Audio Codec Menu Screen (Figure 4-32) Main Screen (Figure 4-33) Network &...
Page 8 AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-64) Saved Voice Message Screen (Figure 4-65) Conference Room Menu Screen (Figure 4-66) SMS Menu Screen (Figure 4-67) Application Setup Menu Screen (Figure 4-68) Remote Broadcast Menu Screen (Figure 4-69) Remote Broadcast Menu Screen...
Page 9 [Table 1-3] Description of the Button Features on the Front Side ......... 20 [ 1-4] Description of the Interfaces on the Rear Side ............21 [Table 2-1] The contents of AP-IP300 IP Phone in the Package Box ........25 [Table 3-1] The Characters Associated with the Dial Pad Buttons ........32 [Table 3-2] Using the Call Button on the Dial Pad ..............
Page 10 AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-17] Description of PPPPoE Menu Screen ............... 80 [Table 4-18] Description of Static IPv6 Menu Screen ............81 [Table 4-19] Description of IPv6 EUI-64 Menu Screen............82 [Table 4-20] Description of LAN Setup Menu Screen............84 [Table 4-21] Description of the Network Status Menu Screen ..........
Page 11: Getting Into Ap-Ip100 Ip Phone Installation Guide
AP-IP300 IP Phone Installation Guide Version 1.0 Getting into AP-IP100 IP Phone Installation Guide This chapter explains the AP-IP300 IP phone installation guide. [Contents of AP-IP300 Installation Guide] The purpose of this guide is to assist the users to install the AP-IP200 IP Phone easily. This guide is composed of six chapters as to follow.
Page 12 AP-IP300 IP Phone Installation Guide Version 1.0 If you have any questions and need any technical support of AP-IP300, please contact AddPac Technology in the followings: AddPac Technology Co., Ltd. Fl. Jeong-Am Building, 769-12 Yeoksam-Dong, Kangnam-Ku, Seoul , Korea Phone (02) 568-3848 Fax (02) 568-3847 E-mail : info@addpac.com...
Page 13: Chapter 1. Introduction
Introduction Introduction AP-IP300 IP phone is designed to provide enhanced IP telephony functionality to meet the wide range of business user requirements. This IP telephone optimally delivers rich featured voice telephony service on ordinary internet infrastructure as well as AddPac IP-PBX environment on local LAN as a fully featured IP extension for the complete AddPac VoIP solution.
Page 14 Privacy and Encryption Features AP-IP300 brings the network security and service security as well. With the built-in CID (Caller ID Detection) feature, user is able to know who is calling before he answers and block the incoming call. Moreover, It...
Page 15: (Figure 1-1) Network Diagram Of Ap-Ip300 Ip Phone
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 1-1) Network Diagram of AP-IP300 IP Phone AddPac Technology Proprietary & Documentation...
Page 16: Ap-Ip300 Ip Phone Hardware Specification
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 1-1] List of Hardware Specification Category Specification Model AP-IP300 Product Category IP Phone (Built-in Speaker Phone) High Performance RISC CPU Architecture Microprocessor Digit and Key Buttopns 3 x 4 Standard Numeric Buttons, 17 Menu/ Function...
Page 17: Ap-Ip300 Ip Phone Software Specification
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 1-2] AP-IP300 Software Specification Category Specification LAN Protocol Static and IEEE 802.1Q VLAN Routing, RIP v1/v2, OSPF v2 WAN Protocol Point-to-Point Protocol (PPPoE for ADSL), etc. Audio Service Voice Codec & - G.711, G.723.1, G.726, G.729, etc.
Page 18 AP-IP300 IP Phone Installation Guide Version 1.0 PPP User Authentication Supports → Password Authentication Protocol(PAP) → Challenge Handshake Authentication Protocol (CHAP) Operation System Performance Analysis for Process, CPU, Connection I/F & Configuration Backup & Restore for APOS Managements Management Debugging, System Auditing, and Diagnostics Support...
Page 19: The Upper View
AP-IP300 IP Phone Installation Guide Version 1.0 This chapter explains the front part’s DIAL and FUNCTION KEY of AP-IP300 IP Phone. The external case is made of high degree of solidity ABS. Main key buttons are equipped on front part so that user can operate all the functions with these buttons.
Page 20: [Table 1-3] Description Of The Button Features On The Front Side
AP-IP300 IP Phone Installation Guide Version 1.0 The following Table 1-3explains each button feature of AP-IP300 on the front side. [Table 1-3] Description of the Button Features on the Front Side Button Names Features Speed Dial Brings out the Speed-Dial Menu...
Page 21: The Layout Of The Rear Side
AP-IP300 IP Phone Installation Guide Version 1.0 The rear side is composed of FXO PSTN backup interface, USB interface, power switch and connector and two (2) Fast Ethernet for WAN/LAN connections. (Figure 1-3) The Rear Side [Table 1-4] explains the interfaces on the rear side.
Page 22: Chapter 2. Preparing For Installation
• Avoid any actions that may lead to the malfunction of the equipment or the operator. Electrical Requirement There are two main sources of electrical problems with AP-IP300 IP Phone : the power supply and static electricity. This section describes safety recommendations for each case.
Page 23: General Requirement
AP-IP300 IP Phone Installation Guide Version 1.0 General Requirement The AP-IP300 IP Phone is ready for use where electronic products are used. However, locations with the following conditions are recommended for maximum performance: • A level and well ventilated location is recommended.
Page 24 RJ-45 to RJ-45 cable for LAN port (included in equipment packing box) Ethernet port AP-IP300 IP Phone has one RJ-45 type RS-232C connector interface in rear side. It can be used for AP-IP200 initial configuration, equipment monitoring and debugging. You must use a cable and a connector.
Page 25: Unpacking And Verifying The Contents
Unpacking and Verifying the Contents Before unpacking, check for external damage of the packaging box. If no external damage has been found, confirm if the following items are enclosed [Table 2-1] The contents of AP-IP300 IP Phone in the Package Box Items Contents...
Page 26: Chapter 3. Installation
AP-IP300 IP Phone Installation Guide Version 1.0 Chapter 3. Installation Connecting Ethernet Interface • Connect AP-IP200’s LAN interface to LAN interface of WAN equipment (Router or ADSL/Cable modem) with RJ45 UTP cable. • There might be some cases of direct connection to router or modem with cross-over cable.
Page 27: (Figure 3-2) Connecting Lan Interface
AP-IP300 IP Phone Installation Guide Version 1.0 • AP-IP300 IP Phone’s Fast Ethernet PC Interface is supposed to be connected into Desktop PC’s LAN Port with Direct-Through cable in IP-Share mode and to be connected into HUB in NAT/PAT or Bridge mode.
Page 28: (Figure 3-3) Ap-Ip300 Ip Phone Pstn Interface Connection
The FXO PSTN interface port is available when PSTN access-line is used or impossible to make a VoIP call due to network problem. PSTN backup is implemented by connecting PSTN access-line to PSTN port, illustrated as following figure. (Figure 3-3) AP-IP300 IP Phone PSTN Interface Connection AddPac Technology Proprietary & Documentation...
Page 29: (Figure 3-4) External Audio In/Out Interface Diagram Of Ap-Ip300 Ip Phone
AP-IP300 IP Phone Installation Guide Version 1.0 Connecting Audio-In/Out Interface for Headset Audio-In/Out port located at left side of AP-IP300 IP Phone is for audio devices such as MIC, Speaker System or Headset Device etc. Connect this port to MIC system or External Speaker System using ‘3.5mm stereo jack’...
Page 30: Structural Diagram Of User Interface Menu
AP-IP300 IP Phone Installation Guide Version 1.0 Structural Diagram of User Interface Menu When you press the Menu key, you can see all the lists of options as they are shown in Figure 3-5. You can use the Menu key even while you are having a conversation on the phone.
Page 31: (Figure 3-5) Structural Diagram Of Ui Menu
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 3-5) Structural Diagram of UI Menu AddPac Technology Proprietary & Documentation...
Page 32: Using The Dial Pad Buttons
AP-IP300 IP Phone Installation Guide Version 1.0 Using the Dial Pad Buttons You can enter the characters by using the dial pad buttons in the Menu options: (Figure 3-6) Dial Pad Buttons [Table 3-1] The Characters Associated with the Dial Pad Buttons...
Page 33 AP-IP300 IP Phone Installation Guide Version 1.0 Ex1) Enter ‘Apple’ Step1 Press 2 button five times then press 7 button twice Step 2 Hit F2 key then press 7 button twice Step 3 Press 5 button four times then press 3 button three times “...
Page 34: Using Send/End Button
AP-IP300 IP Phone Installation Guide Version 1.0 Using Send/End Button The functions of Call button is described in Table 3-2 below: [Table 3-2] Using the Call Button on the Dial Pad Functions Descriptions Retrieving When you just press the Call button and leaving the phone is on the hook, the Recent recent incoming calls are listed.
Page 35: Using Softkeys Supported By Sscp
AP-IP300 IP Phone Installation Guide Version 1.0 Using Softkeys Supported by SSCP Softkey functions are supported by SSCP and change depending on the status of the phone (for example, when you are on a call or the phone is not in use) which are shown at the bottom of the LCD screen and they are interconnected with the 4 buttons of the softkey.
Page 36: [Table 3-6] When You Are Busy On Line
AP-IP300 IP Phone Installation Guide Version 1.0 group EndC (End Call) Ends a call [Table 3-6] When You are Busy on Line Function Description Hold Places a call on hold EndC (End Call) Ends a call Tran(Transfer) Transfers a call to the other extension...
Page 37: [Take 3-8] When The Phone Rings
AP-IP300 IP Phone Installation Guide Version 1.0 [Take 3-8] When the Phone Rings Function Description Answ (Answer) Takes an incoming call [Table 3-9] When the Phone Rings Function Description EndC (End Call) Ends an outgoing call [Table 3-10] On Voice Mail Screen...
Page 38: [Table 3-14] Conference Participants
AP-IP300 IP Phone Installation Guide Version 1.0 the capacity of MCU, the number of conferencing party is limited) Info (Party Info) Information of the present held conferencing participants EndC (End Call) Ends the conference in progress (Ends all the terminals in...
Page 39: Basic Cli Command For Network Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Basic CLI Command for Network Setup CLI command for Looking up the Configured Settings IP300# show run Building configuration... Current configuration: hostname IP300 username root password router administrator interface Loopback0 ip address 127.0.0.1 255.0.0.0 interface FastEthernet0/0 ip address 172.20.103.100 255.255.0.0...
Page 40 [OK] Configuration saved to flash:/apos.cfg IP300# * After the network configuration is finished, you may perform the ping test from AP-IP300 to the default router IP300# ping -c 5 172.20.1.1 PING 172.20.1.1 (172.20.1.1): 56 data bytes 64 bytes from 172.20.1.1: icmp_seq=0 ttl=255 time=0 ms 64 bytes from 172.20.1.1: icmp_seq=1 ttl=255 time=5 ms...
Page 41: Chapter 4. Using Ap-Ip300
AP-IP300 IP Phone Installation Guide Version 1.0 Chapter 4. Using AP-IP300 Default Screen Once the start-up operation is completed, the default screen is organized as it is shown in Figure 4-1. (Figure 4-1) Default Screen [Table 4-1] Description of the Default Screen...
Page 42: (Figure 4-2) Basic Screen Layout
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-2) Basic Screen Layout < Reference: The Speed Button Map can take the speed button information for the Presence Server after registering to the server or the user can create one’s own speed button map. The screen can be changed by the Speed Button Key on the upper right side.
Page 43: Phone Book Menu
AP-IP300 IP Phone Installation Guide Version 1.0 Phone Book Menu The Phone Book is a directory in which user can search by name and number and has the functions including phone number registration, recent call history, group lookup, button list, the default setting.
Page 44: Phonebook - Searching A Phone Number
AP-IP300 IP Phone Installation Guide Version 1.0 – Phonebook Searching a Phone Number The Phonebook uses the registered name, phone number and speed dial number to search the phone number. (Figure 4-5) Search Menu Screen in the Phonebook AddPac Technology Proprietary & Documentation...
Page 45: (Figure 4-6) When Ok Is Pressed On The Dial Pad (It Searches All The Number Which Have Been Saved Previously)
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-2] Description of Search Menu Screen in the Phonebook Phonebook Search Menu Description The search by NAME looks for the registered name throughout the Phone book with the previously saved name. Therefore, cursor automatically moves to the right category in accordance with inputting the letter.
Page 46: (Figure 4-7) When F1 (Modify) Is Pressed
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-7) when F1 (modify) is pressed AddPac Technology Proprietary & Documentation...
Page 47: Phonebook - Registration
AP-IP300 IP Phone Installation Guide Version 1.0 – Phonebook Registration The registration menu takes a new phone number. The user can enter a name, telephone number, speed dial, speed button, IP address or codec information in the Phone Book. The entered phone numbers can be used for speed dial, search and speed button.
Page 48: [Table 4-3] Description Of Registration Menu Screen In The Phonebook
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-3] Description of Registration Menu Screen in the Phonebook Registration Menu Description 1. Enter a new name in the Phonebook 2. Select the group to which the number to registered 3. Enter a phone number 4.
Page 49: (Figure 4-9) Advanced Registration Setup Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-9) Advanced Registration Setup Screen (Figure 4-10) Advanced Setup for Registration Screen [Table 4-4] Description of Advanced Setup for Registration Screen Registration Description 1. Enter a phone number AddPac Technology Proprietary & Documentation...
Page 50 AP-IP300 IP Phone Installation Guide Version 1.0 2. Select a type of audio codec. 3. Enter an IP address AddPac Technology Proprietary & Documentation...
Page 51: Phonebook-Contact Group
AP-IP300 IP Phone Installation Guide Version 1.0 Phonebook- Contact Group The user can specify a group during registration to the phonebook. The specified group can be set with an icon, a bell sound and secret group. The added group can be applied right after the phonebook registration.
Page 52: (Figure 4-12) When The Softkey Of Add Group Or Modify Group (When The Existing Group Presents) Is Pressed
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-12) When the softkey of Add Group or Modify Group (when the existing group presents) is pressed [Table 4-5] Edit Group Category Description Group Name Enter a group name Bell Sond The bell sound for the specified group...
Page 53: Phonebook - Button List
AP-IP300 IP Phone Installation Guide Version 1.0 – Phonebook Button List The Button list is laid out with the names of speed buttons and phone numbers. By using the saved list, the outgoing call can be carried out by Send button, OK button of the keypad and 25 speed buttons.
Page 54: (Figure 4-14) Editing Screen In The Button List
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-14) Editing Screen in the Button List [Table 4-6] Description of the Editing Screen in the Button List Category Description Name Set a name for the Speed Button. Number Set a number for the Speed Button...
Page 55: Phonebook - Recent Call
AP-IP300 IP Phone Installation Guide Version 1.0 – Phonebook Recent Call The recent call displays a call log of the user for incoming and outgoing calls. This feature enables the user to check any incoming call which has been arrived during one’s absence, calls back by using the number of the incoming call and save the number of the incoming calls.
Page 56: [Table 4-7] Description Of The Recent Call Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-7] Description of the Recent Call Screen Category Description incoming/ Displays an incoming call outgoing Displays that the incoming call has not been answered Displays an outgoing call Displays that the outgoing call has not been answered Display the call number for placing a call to the other party directly.
Page 57: Phonebook - Button Profile
AP-IP300 IP Phone Installation Guide Version 1.0 – Phonebook Button Profile The Button Profile can interoperate with the Presence Server only. The user can choose the Button Profile form the Speed Button list which has been provided from the server. In order to interoperate with the Presence Server, you need to set up [4.
Page 58: [Table 4-8] Description Of Button Profile Menu Screen
Category Description Private IP300 Assign a phone number to the Speed Button directly. This profile is displayed when AP-IP300 is not registered to the Presence Server Test 5F Receive the profile form the Presence Server AddPac Technology Proprietary & Documentation...
Page 59: Phonebook - Initialize Pb
– Phonebook Initialize PB The default mode initialization feature deletes all the configured settings of AP-IP300 and all the content of Phonebook, Speed Button numbers and recent cal. This command reboots the system automatically. (Figure 4-17) Initialize PB Menu Screen...
Page 60: Tool Box Menu
AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box menu consists of date/time setting, configuration saving, initialization for factory default mode and language selection. (Figure 4-18) Main Screen (Figure 4-19) Too Box Menu Screen AddPac Technology Proprietary & Documentation...
Page 61: Tool Box - Date & Time
AP-IP300 IP Phone Installation Guide Version 1.0 – Tool Box Date & Time The user can set the date and time. Press F3 to save (Figure 4-20) Date & Time Menu Screen AddPac Technology Proprietary & Documentation...
Page 62: [Table 4-9] Description Of Date & Time Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-9] Description of Date & Time Menu Screen Category Description Year Enter the present year Month Enter the present month Date Enter the present date Hour Enter the present hour Minute Enter the present minute...
Page 63: Tool Box Save All
AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box Save All This UI menu saves the settings which the user has entered in UI. Once the settings are saved, values are preserved even after rebooting. (Figure 4-21) Save All Menu Screen...
Page 64: Tool Box - Factory Default
Tool Box Factory Default The Factory Default deletes all the configured settings of AP-IP300 and all the content on phone book and recent call menu. This command reboots the system automatically. This command is not recommended to use except for some inevitable circumstances.
Page 65: Tool Box Ring
AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box Ring You can set the ringer up to 8 different kinds of sound including mute on the integrated speaker, in the ringer settings. The user can choose the sound that one likes after hearing the 7 different kinds of sound, except the mute, by using F1(Play).
Page 66: (Figure 4-23) Ring Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-23) Ring Screen [Table 4-10] Description of Ring Screen Category Description Ring sound off Set to mute Default Ring #1 The ordinary digital phone sound Default Ring #2 The ordinary analog phone sound...
Page 67: Tool Box - Power Save
AP-IP300 IP Phone Installation Guide Version 1.0 – Tool Box Power Save The Power Save turns off the LCD automatically in a specified time. The LCD can be turned on again by pressing any button on the key pad from the state of Power Save. This setting is recommended for preserving the life time of LCD and maintaining its quality.
Page 68: Tool Box - Version Information
AP-IP300 IP Phone Installation Guide Version 1.0 – Tool Box Version Information This option allows you to verify the version of the software running at this present time. (Figure 4-25) Information Menu Screen [Table 4-11] Description of Information Menu Screen...
Page 69: Tool Box Language
AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box Language This option allows you to verify the language being used at this present time. (Figure 4-26) Language Menu Screen [Table 4-12] Description of Language Menu Screen Category Description English English Language Mode...
Page 70: Tool Box - Password
AP-IP300 IP Phone Installation Guide Version 1.0 Tool Box – Password The Password blocks the access to a particular menu and it can be changed. The default password is 2337. Changing APOS password is not recommended as possible. AddPac Technology Proprietary & Documentation...
Page 71: (Figure 4-27) Password Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-27) Password Menu Screen [Table 4-13] Description of the Password Menu Screen Category Description Use Password Set/ Cancel the password (default : cancel) The password can be set to [Factory Default] [Internet...
Page 72: Av Setup Menu
AP-IP300 IP Phone Installation Guide Version 1.0 AV Setup Menu AV Setup consists of Volume and Audio Codec. (Figure 4-28) Main Menu (Figure 4-29) AV Setup Menu Screen AddPac Technology Proprietary & Documentation...
Page 73: Av Setup - Volume
AP-IP300 IP Phone Installation Guide Version 1.0 AV Setup – Volume The Volume menu consists of Bell Volume, Input/Output Volume Adjustment and External Microphone. (Figure 4-30) Volume Setup Menu Screen AddPac Technology Proprietary & Documentation...
Page 74: [Table 4-14] Description Of Volume Setup Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-14] Description of Volume Setup Screen Category Description Bell Sound Volume Adjust the bell sound volume. The default is set to 5. Input Volume Adjust the input volume of the speaker phone and sender/receiver.
Page 75: Av Setup Audio Codec
AP-IP300 IP Phone Installation Guide Version 1.0 AV Setup Audio Codec The Audio Codec determines a type of voice codec. You can choose the options of G.711[PCM] and G726, G.729, and G.723.1 on UI, basing on the priority level which can be suitable to your network settings.
Page 76: (Figure 4-32) Main Screen
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call Menu The Network & Call consists of WAN, LAN interface setting, SIP/H.323 signaling, FTP service, QoS, call options etc. The user should know this network setup menu for efficient usage of AP-IP200. This menu cannot be skipped for optimized environment.
Page 77: Network & Call - Internet Setup
The Internet Menu has functions related to WAN interface for Internet connection. As there are various network environments, the user has to configure pursuant to his or her own network environment. The WAN protocols supported by AP-IP300 are DHCP, static IPv4, PPPoE, and IPv6 etc.
Page 78: (Figure 4-34) Internet Setup Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-34) Internet Setup Menu Screen [Table 4-15] Description of Internet Setup Menu Screen Category Description DHCP Takes a dynamic IP address from DHCP server such as cable modem, VDSL, IP-ADSL. Static IP Configures IP address manually and build WAN interface such as static IP ADSL, E1/T1 leased line.
Page 79: Network & Call - Internet Setup - Ip Static Ip
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call – – Internet Setup IP Static IP This menu configures WAN interface such as static IP ADSL, E1/T1 leased line. (Figure 4-35) Static IP Menu Screen [Table 4-16] Description of Static IP Menu Screen...
Page 80: Network & Call - Internet Setup - Pppoe
AP-IP300 IP Phone Installation Guide Version 1.0 – Network & Call – Internet Setup PPPoE This is the WAN protocol which takes a dynamic IP address from the PPP Server. ADSL is one of the typical applications in which PPPoE is used.
Page 81: Network & Call - Internet Setup - Static Ipv6
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call – – Internet Setup Static IPv6 This menu configures WAN interface such as static IP ADSL, E1/T1 leased line. (Figure 4-37)Static IPv6 Menu Screen [Table 4-18] Description of Static IPv6 Menu Screen...
Page 82: Network & Call - Internet Setup - Ipv6 Eui-64
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call – – Internet Setup IPv6 EUI-64 This EUI-64 IPv6 address scheme configures company_id(24-bit) basing on the standard of IEEE Registration Authority and extension id(40-bit) basin on the same standard. (Figure 4-38) IPv6 EUI-64...
Page 83: Network & Call - Lan Setup
AP-IP300 IP Phone Installation Guide Version 1.0 – Network & Call LAN Setup This LAN menu is used for protocol setting of AP-IP200 second LAN interface which is used to connect PC or Ethernet Hub. None, DHCP for single (1) PC, DHCP for multiple PC are available as protocols for second fast ethernet LAN port.
Page 84: (Figure 4-39) Lan Setup Menu Screen
Disable LAN Setup (Press OK button to select this option)) DHCP for 1 PC In DHCP protocol mode for single PC, for sharing public same IP address of AP-IP300’s WAN interface and LAN interface connected to PC, AddPac proprietary public IP-Share mechanism is used DHCP for Several PCs DHCP for multiple PC are similar to general IP sharer which links two (2) PCs or more.
Page 85: Network & Call Network Status
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call Network Status This menu displays the current network status of Link Status, IPv4 Protocol, IPv4 address, LAN address, IPv6 Protocol, IPv6 address, DNS, SIP Proxy Server, GK[H.323] Registration Status at a glance.
Page 86: (Figure 4-40) Network Status Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-40) Network Status Menu Screen AddPac Technology Proprietary & Documentation...
Page 87: [Table 4-21] Description Of The Network Status Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-21] Description of the Network Status Menu Screen Category Description Displays whether the link is up/ down of LAN0 WAN Link interface LAN Link Displays whether the link is up/ down of LAN1 (PC)
Page 88: Network & Call Voip Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call VoIP Setup This VoIP setup menu is used for interoperating with SIP server or Gatekeeper on H.323 and SIP basis and adjusting E.164, PSTN number and QoS. (Figure 4-41) VoIP Setup Menu Screen AddPac Technology Proprietary &...
Page 89: Network & Call - Voip Setup - Voip Signaling
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call – VoIP Setup - VoIP Signaling This menu is used for VoIP signaling setup such as H.323, SIP protocol. There are 2 different ways: connecting directly to VoIP network and connecting indirectly through SIP proxy server. Each way needs the different optional settings.
Page 90: Network & Call - Voip Setup - Voip Signaling- Sip Protocol
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call VoIP Signaling SIP Protocol – VoIP Setup - This menu is used for configuring SIP protocol. There are 2 different ways: connecting directly to VoIP network and connecting indirectly through SIP proxy server. Each way needs the different optional settings.
Page 91: Network & Call - Voip Setup - Voip Signaling - H.323 Protocol
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call – VoIP Setup - VoIP Signaling - H.323 Protocol This menu is used for configuring H.323 protocdol. There are 2 different ways: connecting directly to VoIP network and connecting indirectly through SIP proxy server. Each way needs the different optional settings.
Page 92: Network And Call - Voip Setup - Qos
AP-IP300 IP Phone Installation Guide Version 1.0 Network and Call VoIP Setup – – QoS enables transferring range of voice packet within a bandwidth limit. The user has to calculate the bandwidth, then to apply it to QoS. (Figure 4-45) QoS Screen...
Page 93: Network And Call - Voip Setup - Sip Options
AP-IP300 IP Phone Installation Guide Version 1.0 Network and Call VoIP Setup – SIP Options – This menu is used for configuring additional features and options of SIP protocol. These optional settings are dependent on the network configuration. (Figure 4-46) SIP Options Menu Screen...
Page 94: [Table 4-26] Description Of Sip Options
Set Session Timer Retry Counter SIP UA Retry Counter sets SIP INVITE re-transmission count when AP-IP300 is dial-out. When there is fault on network or network quality is not good, Trying message of INVITE message will be delayed. In this case AP-IP300 transfer next INVITE message.
Page 95: Network & Call - Voip Setup- Pstn Prefix
When user wants to access the FXO interface for PSTN backup, this prefix number is used as PSTN access code. Additionally, AP-IP300 IP phone supports the PSTN back-up service when VoIP service is impossible due to network failure or VoIP call service is interrupted by an exception.
Page 96: Network & Call - Additional Service
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – A The Additional Service menu sets up Call Transfer, DND, Call Wait and Auto Response. (Figure 4-48) Additional Service Menu Screen AddPac Technology Proprietary & Documentation...
Page 97: Network & Call - Additional Service - Call Forward
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – A – Call Forward This is the menu sets up the call forward when the user is busy on line or unable to answer the call or forward a call unconditionally.
Page 98 AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-28] Description of Call Forward Menu Screen Category Description Unconditional Enter the number to be forwarded to no matter what (Call Forwarding Unconditional) Unconditional Setup Enable or Disable Call Forwarding Unconditional (the default...
Page 99: Network & Call - Additional Service - Dnd(Do Not Disturb)
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – DND(Do Not Disturb) – A Do Not Disturb (DND) features allows you to turn off the ringer (Ring Silence) for an incoming call or to reject the call (Call Reject. You may hold pressing the leave of absence button of the IP-Phone for more than 2 seconds to enable or disable this function.
Page 100: (Figure 4-51) Dnd Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-29] Description of DND Menu Screen Category Description Call Reject Set the mode to Call Reject Ring Silence Set the mode to Ring Silence Hold pressing more than 2 seconds [DND] =>Enable DND...
Page 101: Network & Call - Additional Service - Call Wait Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – Call Wait Setup – A Call Wait feature enables you to receive a second incoming call with on the same line without disconnecting the first call. This call feature allows you to receive an auditory call alert while you are on the first call.
Page 102: Network & Call - Additional Service - Auto Response
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – A – Auto Response This feature allows your telephone to answer a call automatically and you do not have to pick up the phone. You can set the interval of answering a call selectively: 3, 5, 10 or 15 seconds.
Page 103: Network & Call - Additional Service - Multi Number
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service Multi Number – A – The Multi Number allows you to set the native number for the Outbound Call, as to select the one number among many numbers that have been assigned. You can take many numbers of incoming calls, but you can send only the predetermined number of the outgoing call at the default setting.
Page 104: Network & Call - Additional Service - Service Port
This menu activates or deactivates FTP, TELNET, TFTP, SNMP protocol service of AP-IP300. You can use FTP to access to AP-IP300 from a remote location and Telnet is used for changing all kinds of information and monitoring and SNMP is also used to access to AP-IP300 from a remote location.
Page 105: [Table 4-33] Description Of Service Port Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-33] Description of Service Port Menu Screen Category Description Actives/Deactivates the FTP service protocol. Default is enable mode (activating FTP service). Default port number is 21. Actives/Deactivates the TELNET service protocol. Default is enable mode (activating TELNET service).
Page 106: Network & Call - Additional Service - Auto Upgrade
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service – A – Auto Upgrade Whenever a new feature is added, the software (firmware) of the IP phone needs to be upgraded. One of the ways of doing this upgrade is download the new software by using a network transmission protocol such as ftp which is capable of transmitting a large files.
Page 107 AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-34] Description of Auto Upgrade Menu Screen Category Description Enter URL of the Auto Upgrade server Ex)down.addpac.com/apos/IP300/packing.lst Login Name Enter the ID for an authorized access to the Auto Upgrade server Ex) addpac...
Page 108: Network & Call - Additional Service - Sscp Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call dditional Service SSCP Setup – A – SSCP Smart Service Control Portocol) is the AddPac proprietary protocol operates between the AddPac IP-PBX systems and IP terminals. The IP-PBX systems support many different call features, through SSCP, in addition to the basic call features of the IP Phone itself.
Page 109: (Figure 4-57) Sscp Setup Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-57) SSCP Setup Menu Screen [Table 4-35] Description of SSCP Setup Screen Category Description Either enable or disable the setting mode of SSCP Setup SSCP (On/Off) Call-manager 1 ~ 5 Configure the Call Manager server: 5 servers can configured maximum.
Page 110: Network & Call - Presence
Network & Call – Presence When AP-IP300 is connected with Presence Server, the IP300 can take the Speed Button Key from the server. The LED of each speed button key is changed on real time basis, so the present status of the user can be informed.
Page 111: Network & Call - Presence - Presence
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call Presence – – Presence In order to register to Presence Server, you may enter an ID and password. When you enter one server address and port, the Presence Server Number is indicated as 1. And then you may enter the ID and password which have been registered to the IP-PBX.
Page 112: Network & Call - Presence - Presence Server
AP-IP300 IP Phone Installation Guide Version 1.0 Network & Call Presence – Presence Server – You can enter an IP and port to register to Presence Server. The default port number is 5051 and the server address supports both IPv4 / IPv6.
Page 113: (Figure 4-61) Main Screen
AP-IP300 IP Phone Installation Guide Version 1.0 Application Applications composed of a group of the call features including Message Box, Voice Mail Box, Conference. You can use Message Box and Voice Box only when they are connected to and supported by SSCP.
Page 114: Application - Voice Mail
AP-IP300 IP Phone Installation Guide Version 1.0 Application Voice Mail – Voice Mail enables you to check the voice messages by pressing Play key. You should know the user’s password which has been registered to IP-PBX to listen to the voice messages.
Page 115: (Figure 4-64) Saved Voice Message Screen
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 4-64) Saved Voice Message Screen AddPac Technology Proprietary & Documentation...
Page 116: Application - Conference
AP-IP300 IP Phone Installation Guide Version 1.0 Application Conference – This feature enables you to see the list of connections can be made for a conference call at the present time and you can join the conference by just pressing call button. There are 4 different ways of...
Page 117: [Table 4-39] Description Of The Conference Room Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-39] Description of the Conference Room Menu Screen Category Description 1. The icon for the conference room represents the Dial-out conference 2. the name of the conference room 3. The Speed Dial Number for the Conference 4.
Page 118: Application - Sms
AP-IP300 IP Phone Installation Guide Version 1.0 Application – The Message allows you to transmit and verify SMS text messages between one terminal and the other, when it is connected to SSCP. The messages can be sent to 9 recipients at same time. The received messages are kept as pop-up notice in the desktop area.
Page 119: [Table 4-40] Description Of Sms Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-40] Description of SMS Menu Screen Category Description Write SMS messages to be sent Write Text Message Received Message Store the SMS messages in the box which have been received Saved Message...
Page 120: Application - Application Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Application – Application Setup The Application Setup menu consists of Remote Broadcast, Chime and Client Information. To use Remote Broadcast, you need the AddPac Broadcasting Equipment (AP3120) and broadcasting management program (e-MBMS Server). To preview Client Information, you need to save the client information and interoperate with the server.
Page 121 AP-IP300 IP Phone Installation Guide Version 1.0 Category Description Remote Broadcast Set up the IP, Port, ID, Password for the remote broadcast Chime Setup Select Chime bell on/off prior to the broadcasting Client Information Setup Set up the IP, port for Client Information...
Page 122: Application - Application - Remote Broadcast
AP-IP300 IP Phone Installation Guide Version 1.0 Application Application – Remote Broadcast The menu sets up e-MBMS Server address and Port, User ID, Password for the Remote Broadcast. The Remote Broacast can be used in the environment installed with the AddPac Broadcasting Equipment (AP3120) and Broadcasting Management Program (e-MBMS Server).
Page 123: Application Application Setup - Chime Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Application Application Setup – Chime Setup This menu sets up or cancels the Chime Bell for starting up the Remote Broadcast. (Figure 4-69) Remote Broadcast Menu Screen [Table 4-43] Description of Remote Broadcast Menu Screen...
Page 124: Application - Application Setup - Client Info Setup
AP-IP300 IP Phone Installation Guide Version 1.0 Application Application Setup – C lient Info Setup When to take a call, this menu displays a clients information, so you can check the sender’s name, resident’s ID and home address. From Client Info Setup menu you can set up the IP, port, enabling viewing the client’s information, and Auto CRM pop-up.
Page 125: Application - Client Info
AP-IP300 IP Phone Installation Guide Version 1.0 Application Client Info – When to take a call, this menu displays a clients information, so you can check the client’s name, resident’s ID and home address. (Figure 4-71) Client Info Menu Screen...
Page 126: Application - Remote Broadcast
AP-IP300 IP Phone Installation Guide Version 1.0 Application Remote Broadcast – The Remote Broadcast Menu enables the user to check the broadcasting status of each terminal. Through this menu, the user can select the terminals to be participating in broadcasting and control...
Page 127: System Setup Menu
AP-IP300 IP Phone Installation Guide Version 1.0 System Setup Menu The System Setup Menu can set up the name and number to be displayed on the desktop area and disable or enable the speed dial number to send out a call.
Page 128: System Setup - User Information
AP-IP300 IP Phone Installation Guide Version 1.0 – System Setup User Information This menu sets up the name and number that the user wants on the desktop area. Even if the name and number have been set up, the name and number are displayed on the desktop area, which are taken from the IP-PBX.
Page 129: [Table 4-45] Description Of User Information Menu Screen
AP-IP300 IP Phone Installation Guide Version 1.0 [Table 4-45] Description of User Information Menu Screen Category Description Enter the name to be displayed on the desktop Name area Number Enter the number to be displayed on the desktop area AddPac Technology Proprietary & Documentation...
Page 130: System Setup - Speed Dial Setup
AP-IP300 IP Phone Installation Guide Version 1.0 System Setup Speed Dial Setup – The Speed Dial Setup menu allows the user to place a call by pressing the speed dial number which has been assigned with the outgoing call number. In order to use this feature, you may enable the Speed Dial and the Speed Dial Number should be assigned to the Phonebook.
Page 131: System Setup - Start Menu
AP-IP300 IP Phone Installation Guide Version 1.0 System Setup Start menu – The default screen (Tree) and Speed Button Map can be used selectively. Instead of the default screen, the Speed Button key can be used on the upper left side of the keypad to change the desktop screen.
Page 132: Chapter 5. Testing Operation
Testing Operation Booting Procedure and Operating Bases The things that you have to know, prior to turning on the power of AP-IP300, are the booting procedure. • AP-IP300 checks its basic operation of its interface, memory and CPU through a self-testing procedure •...
Page 133: (Figure 5-1) Terminal Emulator Hyperterminal Of Ms-Windows
AP-IP300 IP Phone Installation Guide Version 1.0 Using the Hyper-Terminal for the Console Terminal Emulator Application must be installed for using the PC for the console terminal. Hyper- Terminal Application is used for MS-Windows. (Figure 5-1) Terminal Emulator HyperTerminal of MS-Windows After HyperTerminal is performed, determine the name of the new connection.
Page 134: (Figure 5-2) Entering The Name Of The Connection In Hyperterminal
AP-IP300 IP Phone Installation Guide Version 1.0 (Figure 5-2) Entering the name of the connection in HyperTerminal AddPac Technology Proprietary & Documentation...
Page 135: (Figure 5-3) Access To Telnet By Using Tcp/Ip
AP-IP300 IP Phone Installation Guide Version 1.0 Select the interface of which the console cable is connected Since AP-IP300 does not support Console Interface, the IP Address of LAN1 interface is used to connect PC as it is shown in the following figure: (LAN1 default ip address : 192.168.10.1)
Page 136: (Figure 5-4) Login Screen
AP-IP300 IP Phone Installation Guide Version 1.0 After completing the setup, you can see the login screen of AP-IP300 in the following Figure (Figure 5-4) Login Screen You may see the 2 types of prompt: ‘AP-IP300>’ and ‘AP-IP300#’. The prompt with starting with ‘>’...
Page 137: Using Apos Commands
AP-IP300 IP Phone Installation Guide Version 1.0 Using APOS Commands NOTE All the product lines of AddPac Technology are imbedded with APOS AddPac Operating System). Therefore, all the basic settings of CLI (Command Line Interface) are same. The commands are used for the following types of modes:...
Page 138: [Table 5-1] Commands For The General User Mode
AP-IP300 IP Phone Installation Guide Version 1.0 General User Mode Commands These are the functions that all the types of the users who logged in the system The prompt for the general user can be indicated as ‘IP-300>’. [Table 5-1] Commands for the General User Mode...
Page 139: [Table 5-2] Anagement Mode Commands
AP-IP300 IP Phone Installation Guide Version 1.0 Management Mode Commands These are the types of commands that the administrator, whoever logged in the system, can use. To get into configuration of this system mode, the user must be logged in as an administrator. In this mode, the commands can be same as General User mode such as ‘show’, but more information can be...
Page 140 AP-IP300 IP Phone Installation Guide Version 1.0 Indicate the users connected to vty whoami Indicate a type of connection established at the present time write Save the configuration in operation process AddPac Technology Proprietary & Documentation...
Page 141: Configuring Password
The user account and password must be know to the administrator only. If they are exposed to any other, the product can not be operated properly. [Table 5-5] User Administration AP-IP300# configure terminal AP-IP300(config)# AP-IP300(config)# username {ID} password {password} {administrator | operator | AddPac Technology Proprietary & Documentation...
Page 142 AP-IP300 IP Phone Installation Guide Version 1.0 user} AP-IP300(config)# AddPac Technology Proprietary & Documentation...
Page 143: [Table 5-6] Configuring Fxs/Fxo Port
AP-IP300 IP Phone Installation Guide Version 1.0 Configuring FXS/FXO Port * Check show run first [Table 5-6] Configuring FXS/FXO Port IP300# show run Building configuration... Current configuration: version 8_42_003 hostname IP300 username root password router administrator interface Loopback0 ip address 127.0.0.1 255.0.0.0 interface FastEthernet0/0 ip address 172.17.201.88 255.255.0.0...
Page 144 AP-IP300 IP Phone Installation Guide Version 1.0 dial-peer voice 0 pots destination-pattern 1004 port 0/0 IP300# IP300# con t => FXS/FXO port dial peer configuration IP300(config)# dial-peer voice 1 pots IP300(config-dialpeer-pots-1)# destination-pattern 1014 Assigning the port numbers of FXS/FXO => Assigning the port that has been...
Page 145 AP-IP300 IP Phone Installation Guide Version 1.0 ! Voice port configuration. ! SPEECH voice-port 0/0 ! FXS voice-port 0/1 ! Pots peer configuration. dial-peer voice 0 pots destination-pattern 1004 port 0/0 dial-peer voice 1 destination-pattern 1014 port 0/1 AddPac Technology Proprietary & Documentation...
Page 146: Chapter 6. Emergency Recovery
AP-IP300 IP Phone Installation Guide Version 1.0 Chapter 6. Emergency Recovery The entire AddPac VoiIP product line has 2 different zones. One is to store APOS and Boot Loader is the other. The functions of Boot Loader can be used in the followings: 1.
Page 147: Entering The Boot Loader Mode
AP-IP300 IP Phone Installation Guide Version 1.0 Entering the Boot Loader mode Since AP-IP100 does not have console interface, it is not possible to enter the mode of Boot Loader by using ‘ctrl+x’, ctrl+c’ , which is possible for APOS with presence of console such as ‘send break’., during the booting process.
Page 148: Initialize Apos Settings
AP-IP300 IP Phone Installation Guide Version 1.0 Initialize APOS Settings When the user lost the default IP address of the IP Phone (192.168.10.1) that enables TELNET and FTP access, after making a change, the default IP can be recovered by initializing APOS settings (Please be cautious when you initializes APOS configuration, all the existing settings of configuration are to be erased.)
Page 149: Downloading Apos Image File In Boot Loader Mode
AP-IP300 IP Phone Installation Guide Version 1.0 Downloading APOS Image File in Boot Loader Mode The AddPac AP-IP100 IP Phone allows FTP access, which is supported by the binary code, to transmit APOS image file. APOS image of AP-IP100 can be downloaded from PC by using FTP.
Page 150: Chapter 7. Appendix
AP-IP300 IP Phone Installation Guide Version 1.0 Chapter 7. Appendix This Appendix provides information about the Pinout specifications of the following cables used with AP-IP200 IP Phone. Console Port Signal and Pinout (RJ-45 to DB9) Ethernet UTP Cable Assemble (RJ-45 to RJ-45) Pinout [RS-232C Console Port Signal &...
Page 151: Figure 7-1 100Base-Tx Rj-45 Connector
AP-IP300 IP Phone Installation Guide Version 1.0 UTP Cable (RJ-45 to RJ-45) Pinout Specification In order to connect the LAN port of this equipment with other equipments (i.e. HUB), the RJ-45 to RJ-45 Ethernet Cable is used. The RJ-45 Connector Pin sequence is provided below and the signal and Pinout specifications are enlisted at the below table.
Page 152: Acronyms And Glossary
AP-IP300 IP Phone Installation Guide Version 1.0 Acronyms and Glossary Terms Definition & Description An acronym for Asymmetric Digital Subscriber Line, ADSL is a method of ADSL transmitting data over traditional copper telephone lines. Data can be downloaded at speeds of up to 1.544 Megabits per second and uploaded at speeds of 128 Kilobits per second (asymmetric).
Page 153 AP-IP300 IP Phone Installation Guide Version 1.0 cable modem can be used to achieve more bandwidth. Cable network also requires modularization and demutualization process while sending the data. A call center is a central place where customer and other telephone calls are...
Page 154 AP-IP300 IP Phone Installation Guide Version 1.0 of analog signal to bit stream with Pulse Code Modulation method. 2. DSP software algorithm for compressing/ decompressing voice or audio signal DTE interface whether the command is delivered to the host. Console...
Page 155 AP-IP300 IP Phone Installation Guide Version 1.0 distance of still pictures printed matter and similar documented material data that is transmitted between network points as a unit complete with Frame addressing and necessary protocol control information. A frame is usually transmitted serial bit by bit and contains a header field and a trailer field that "frame"...
Page 156 AP-IP300 IP Phone Installation Guide Version 1.0 startup and request admission to a call from the gatekeeper. An International Telecommunication Union (ITU-T) standard for H.225.0 H.225 session control and packetization. It defines various protocols of RAS, Q.931, RTP and etc.
Page 157 AP-IP300 IP Phone Installation Guide Version 1.0 independently without having to coordinate with each other. An ISP (Internet service provider) is a company that provides individuals and other companies access to the Internet and other related services such as Web site building and virtual hosting. An ISP has the equipment and the telecommunication line access required to have a point-of-presence on the Internet for the geographic area served.
Page 158 AP-IP300 IP Phone Installation Guide Version 1.0 LANs but smaller than WANs. Compare with: LAN, WAN. MGCP, also known as H.248 and Megaco, is a standard protocol for handling MGCP the signaling and session management needed during a multimedia conference. The protocol defines a means of communication between a media...
Page 159 AP-IP300 IP Phone Installation Guide Version 1.0 user's computer and the ISP using its own Link Control Protocol (LCP). PPP supports PAP, CHAP and other authentication protocols as well as compression and encryption. Protocol Stack Any set of communication protocols, such as TCP/IP, that consists of two or more layers of software and hardware.
Page 160 AP-IP300 IP Phone Installation Guide Version 1.0 2. Rapid Transport Protocol. Provides pacing and error recovery for APPN data as it crosses the APPN network. With RTP, error recovery and flow control are done end-to-end rather than at every node. RTP prevents congestion rather than reacts to it.
Page 161 AP-IP300 IP Phone Installation Guide Version 1.0 related equipment capable of carrying a 1.544 Mbps DS-1 signal. Term often used interchangeably with DS-1. Refer to: AMI, B8ZS, DS-1. Transmission Control Protocol/Internet Protocol, The protocol suit developed TCP/IP by DoD (USA) in 1970s for the worldwide inter-network development. TCP &...
Page 162 AP-IP300 IP Phone Installation Guide Version 1.0 telephony for a set of facilities for managing the delivery of voice information using the Internet Protocol (IP). In general, this means sending voice information in digital form in discrete packets rather than in the traditional circuit-committed protocols of the public switched telephone network (PSTN).
Page 163 AP-IP300 IP Phone Installation Guide Version 1.0 AddPac Technology Co., Ltd. 2F & 3F, Jeong-Am Bldg., 769-12 Yeoksam- dong, Gangnam-gu, Seoul, 135-080, Korea Tel: +82 2 568 3848 Fax: +82 2 568 3847 Email: sales@addpac.com http:// www.addpac.com AddPac Technology Proprietary & Documentation...

AddPac AP-IP300 Installation And Operation Manual

Getting into AP-IP100 IP Phone Installation Guide

Chapter 1. Introduction

Introduction

Product Overview

AP-IP300 IP Phone Hardware Specification

AP-IP300 IP Phone Software Specification

The Upper View

The Layout of the Rear Side

Chapter 2. Preparing for Installation

Installation Requirement

Electrical Requirement

General Requirement

Unpacking and Verifying the Contents

Chapter 3. Installation

Structural Diagram of User Interface Menu

Using the Dial Pad Buttons

Using Send/End Button

Using Softkeys Supported by SSCP

Basic CLI Command for Network Setup

Chapter 4. Using AP-IP300

Default Screen

Phone Book Menu

Phonebook - Searching a Phone Number

Phonebook - Registration

Phonebook-Contact Group

Phonebook - Button List

Phonebook - Recent Call

Phonebook - Button Profile

Phonebook - Initialize PB

Tool Box Menu

Tool Box - Date & Time

Tool Box Save All

Tool Box - Factory Default

Tool Box Ring

Tool Box - Power Save

Tool Box - Version Information

Tool Box Language

Tool Box - Password

AV Setup Menu

AV Setup - Volume

AV Setup Audio Codec

Network & Call - Internet Setup

Network & Call - Internet Setup - IP Static IP

Network & Call - Internet Setup - Pppoe

Network & Call - Internet Setup - Static Ipv6

Network & Call - Internet Setup - Ipv6 EUI-64

Network & Call - LAN Setup

Network & Call Network Status

Network & Call Voip Setup

Network & Call - Voip Setup - Voip Signaling

Network & Call - Voip Setup - Voip Signaling- SIP Protocol

Network & Call - Voip Setup - Voip Signaling - H.323 Protocol

Network and Call - Voip Setup - Qos

Network and Call - Voip Setup - SIP Options

Network & Call - Voip Setup- PSTN Prefix

Network & Call - Additional Service

Network & Call - Additional Service - Call Forward

Network & Call - Additional Service - DND(Do Not Disturb)

Network & Call - Additional Service - Call Wait Setup

Network & Call - Additional Service - Auto Response

Network & Call - Additional Service - Multi Number

Network & Call - Additional Service - Service Port

Network & Call - Additional Service - Auto Upgrade

Network & Call - Additional Service - SSCP Setup

Network & Call - Presence

Network & Call - Presence - Presence

Network & Call - Presence - Presence Server

Application - Voice Mail

Application - Conference

Application - SMS

Application - Application Setup

Application - Application - Remote Broadcast

Application Application Setup - Chime Setup

Application - Application Setup - Client Info Setup

Application - Client Info

Application - Remote Broadcast

System Setup Menu

System Setup - User Information

System Setup - Speed Dial Setup