Page 1
NOTE: Please read all instructions carefully before using this product Table of Contents APEX Safety Notice Combo Bench w/ Wt. Set Hardware Identifier TSA-499 Assembly Instruction Parts List Warranty Ordering Parts Model TSA-499 Retain This Manual for Reference 08-03-05 OWNER'S MANUAL IMPEX INC.
WARRANTY...… ORDERING PARTS... BEFORE YOU BEGIN Thank you for selecting the APEX Combo Bench TSA-499 by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. READ ALL IMPEX INC.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown.
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beams (#1 & 2) by a Cross Brace (#8) in the mid-span. Align the holes and secure each end with one 4 ¾”...
Page 8
STEP 2 (See Diagram 2) A.) Attach the Leg Developer Holder (#4) to the Front Stabilizer (#3). Secure it with two M10 x ¾” Allen Bolts (#45) and Ø ¾” Washers (#49). B.) Attach the Leg Developer Holder to the Main Seat Support (#5). Secure it with two M10 x 2 3/8”...
Page 9
STEP 3 (See Diagram 3) A.) Attach the Leg Developer (#6) to the Leg Developer Holder (#4). Secure it with one M10 x 2 7/8” Allen Bolt (#44), two Ø ¾” Washers (#49), and one M10 Aircraft Nut (#48). B.) Insert two Foam Roll Tubes (#16) halfway through the holes on the Leg Developer (#6). Push four Foam Rolls (#27) onto the Tubes from both sides.
Page 10
STEP 4 (See Diagram 4) A.) Attach the side-holes on the Backrest Supports (#15) to the pivot on the Main Seat Support (#5). Place the other end of Backrest Supports rest against the Backrest Adjustment Bar. B.) Attach the Backrest Board (#18) to the Backrest Supports. Secure it with four M6 x 1 3/8”...
Page 11
STEP 5 (See Diagram 5) A.) Attach the Cable (#20) to the open slot on the top of the Lat Bar Frame (#7). Attach a Pulley (#35) to the Cable. Secure the Pulley to the open slot with one M10 x 2 1/8” Allen Bolt (#43), two Pulley Bushings (#21), and one M10 Aircraft Nut (#48).
PARTS LIST KEY NO. DESCRIPTION Left Upright Beam Right Upright Beam Front Stabilizer Leg Developer Holder Main Seat Support Leg Developer Lat Bar Frame Cross Brace Backrest Adjustment Bar Lat Bar Sliding Weight Post Left Safety Catch Right Safety Catch Weight Bar Backrest Support Foam Roll Tube...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.