Advertisement
CONSUMPTION DATA
Temperature
Programme
(°C)
White Cotton / Antibacterial
95
Cotton
60
Cotton with "Eco"***
60
Cotton
40
Synthetics
60
Synthetics
40
Daily load
40
Quick wash
30
Delicates
40
Baby
40
Handwash
40
Wool
40
Lingerie
30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE LID AND
SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in the chapter "Detergent and Additives"
in your Instructions for Use.
1. Turn the programme selector to the desired
programme. The display shows the programme
duration in hours and minutes as well as the
predefined temperature. The "Start/Pause"
button flashes.
2. The temperature can be altered by pressing
the "Temperature" button.
3. The indication lamp of the predefined spin speed
lights up; in case you want to set another spin
speed, press the "Variable spin" button.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
"Eco" button
• With a modified temperature profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
"Easy ironing" button
• Can be used together with "Cotton",
"Synthetics" and "Daily load" programmes to
make ironing easier.
Load
Water
Energy
Approx. Programme Duration
(kg)
(l)
(kWh)
(hours : minutes)*
5.5
55**
1.70
1:55
5.5
49
1.02
2:25
5.5
49
0.93
2:35
5.5
53
0.55
2:00
2.5
53**
0.85
1:30
2.5
47
0.50
1:15
3.0
43
0.48
1:00
3.0
36
0.30
0:30
1.5
51
0.50
0:45
5.5
73
0.55
2:15
1.0
43
0.50
0:35
1.0
53
0.50
0:45
1.0
42
0.30
0:35
• Increases the water quantity and the clothes are
spun very gently.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
• Do not use liquid detergent for the main wash
when activating the Prewash option.
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water, for washing baby linen and
helping people with allergies.
"Rinse hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes "Synthetics", "Daily load" and
"Delicates".
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• If you select "Rinse hold", do not leave the laundry
to soak for too long.
Note: The programme stops to "Rinse hold" at
the time the "Rinse hold" light in the programme
sequence indicator is on. The indication lamp
next to the "Start/Pause" button flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain" programme
and press the "Start/Pause" button.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The "Start Delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper. Do not use liquid detergent
when activating the "Start Delay".
• Select programme, temperature and options.
• Press the "Start Delay" button to select the delay
time by 1 to 23 hours;
• Press the "Start/Pause" button.
The indication light over the "Start Delay"
button flashes and the countdown of the delay
time begins. The dot between hours and
minutes of the delay time indicated flashes.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the "Start/Pause" button,
the number of hours preselected can be reduced
by pressing and holding the "Start Delay"
button. From 1 hour on, the delay time can also
be reduced in steps of 10 minutes.
To cancel the "Start Delay"
..before you press the "Start/Pause" button:
• Turn the programme selector to another
position or press the "Reset" button.
..after having pressed the "Start/Pause" button:
• Press the "Reset" button for at least 3 seconds - the
start delay time disappears from the time display.
PROGRAMME START
Open the tap and press the "Start/Pause" button. The
indication lamp next to the "Start/Pause" button lights
up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time.
Due to variations in load and temperature of inlet
water, the remaining time is newly calculated in certain
programme phases. If this is the case, an animation
appears on the time display.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the
lamp lights to show that the lid can be opened. As
long as a wash programme is running, the lid
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to "Cancel
(Reset) a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused by
a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use; if
the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the "Troubleshooting Guide" in the
Instructions for Use.
"Clean filter"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
("Removing the Filter").
PROGRAMME END
• All the lights of the programme sequence
indicator are off, and the "Door open"
indication lights up.
1. Turn the programme selector to the "Off/O" position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open to allow the inside of the
machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position
where the previous programme was interrupted.
Do not add detergent for this programme.
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
The "Reset" button cancels a programme before
the end.
• Press the "Reset" button for at least 3
seconds. Any existing water is drained out
before the lid can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 312 10588
Advertisement
