Page 1
Instruction Manual 1100W Transfer Pump on Trolley Model: YW1100TP WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
WARRANTY YARDWORKS TWO YEARS LIMITED WARRANTY Your YARDWORKS product is covered for a period of 2 years from the ORIGINAL date of purchase and is intended for home use only. The warranty covers faulty parts or workmanship. The warranty is only made available by returning the product to your point of purchase with a confirmed cash register receipt.
INTRODUCTION Congratulations on purchasing the YARDWORKS 1100W Transfer Pump on Trolley. We aim to provide quality products at an affordable price. Before using, it is most important that you read and follow the instructions in this manual, even if you feel you are quite familiar with this type of product.
WARNING! THIS PRODUCT IS NOT SUITABLE FOR USE WITH DRINKING (POTABLE) WATER. PACKED CONTENTS 1 x Transfer pump on trolley (YW1100TP) 1 x Instruction manual FITTINGS AND TOOLS REQUIRED FOR INSTALLATION Note: Recommended items below are not included and are readily available from your local Bunnings store.
ELECTRICAL SAFETY WARNING! When using mains-powered equipment, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage. Read and understand the manual prior to operating this pump. Save these instructions and other documents supplied with this pump for future reference. The electric motor has been designed for 230V and 240V only.
DESCRIPTION OF SYMBOLS Volts Hertz Alternating current Watts /min Revolutions or No load speed reciprocation per minute Litres ºC Degrees celsius p/hr Per hour Pressure rating (kilopascals) Pressure rating Insulation class Polyvinyl chloride IPX8 Ingress protection from water Regulator compliance mark Warning Read instruction manual...
GENERAL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 1) WORK AREA a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate pumps in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pumps create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a pump.
ADDITIONAL SAFETY INSTRUCTIONS FOR PUMPS Caution: Not intended for cleaning and other maintenance of swimming pool. WARNING! This product is intended for pumping water in a Home Domestic application. Do not use it for corrosive, abrasive, explosive or dangerous liquids. Fluids other than water may damage the water pump and/or create a fire hazard.
SET-UP & INSTALLATION Suction Inlet Connecting Hose or Pipe to the Suction Inlet Remove the plastic protection cover from the suction inlet (5) (Fig. 1). Note: It is recommended that you use a preliminary filter and suction set with suction hose, suction strainer and non-return valve, in order to prevent long priming periods and unnecessary damage to the pump as a result of stones and Fig.
Page 11
SET-UP & INSTALLATION (cont.) Positioning the Hose or Pipe Position the input hose or pipe so that it rises from the water drawing source to the pump. Avoid positioning the input hose or pipe higher than the pump, as this would delay the escape of air bubbles from the input hose or pipe and impede the priming process (see section ‘starting the pump’...
Page 12
SET-UP & INSTALLATION (cont.) Priming Priming the pump prepares the motor for safe operation. 1. Ensure the pump is turned off at the mains power. 2. Remove the plastic protection cover from the discharge outlet (2) pump housing (Fig. 6). Fig.
OPERATION Turning the Pump On and Off Note: When the pump is fully primed and air is flushed out of the suction cycle, the pump is ready to operate. The pump may take several minutes to fully prime air from the suction line and inside the pump. 1.
MAINTENANCE In ordinary conditions, this pump does not require any maintenance. Make sure the pump is disconnected from electric power supply before performing maintenance operation. Cleaning the pump body Use a moist cloth to wipe down the pump body (5). Allow to dry thoroughly before storing in a dry location that is protected from bad weather conditions.
TROUBLE SHOOTING Symptom Possible Cause Suggested Solution The pump does not pump There is no power reaching the pump Check the mains power outlet, ensure that the water/the motor does electrical plug of the pump has been correctly not run inserted The motor thermal overload Turn the pump off and switch power off at the...