Subscribe to Our Youtube Channel
Related Manuals for Modern Flames HF36CBI
Summary of Contents for Modern Flames HF36CBI
- Page 1 Home Fire CBI Electric Series HF36CBI—HF42CBI—HF60CBI INSTALLATION/SERVICE INSTRUCTIONS FOR USE IN UNITED STATES AND CANDA...
- Page 2 Read these instructions completely before beginning installation. Failure to follow them could cause a heater malfunction resulting in serious injury and/or property damage. WARNING: All electric heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are or are stored. This fireplace meets the construction and safety standards of H.U.D.
-
Page 3: Table Of Contents
USER INSTRUCTIONS TABLE OF CONTENTS Important Instructions ........3 Operation ........... 9 Power Data ..........4 Service Parts ..........10 Product Dimensions ........4 Frequently Asked Questions ...... 12 Box Contents ..........5 Troubleshooting ......... 12 Unpacking and Testing ........ 6 Cleaning and Maintenance Instructions .. -
Page 4: Power Data
USER INSTRUCTIONS IMPORTANT INSTRUCTIONS the heater off and inspect for any objects on locations. Never locate heater where it may or adjacent to the heater that may have fall into a bathtub or other water container. blocked the airflow or otherwise caused high 14. -
Page 5: Box Contents
USER INSTRUCTIONS Home Fire 42 42” W x 28 1/2” H x 11 1/2” D Home Fire 60 60” W x 28 1/2” H x 11 1/2” D BOX CONTENTS 4 Large Washer Head 1 Fire Unit Screws 1 Glass Face 1 Remote... -
Page 6: Unpacking And Testing
USER INSTRUCTIONS UNPACKING AND TESTING This heater is for use on 120 volts. The cord has a plug as shown at A. An adapter as shown at C is available for connecting three- blade grounding-type plugs to two-slot recep- tacles. The green grounding lug extending from the adapter must be connected to a per- manent ground such as a properly grounded outlet box. -
Page 7: Installation
INSTALLATION INSTALLATION WARNING - RISK OF FIRE! WARNING: If the information in these in- The power cord must not be pinched or structions is not followed exactly, a fire against a sharp edge. Secure cord to or explosion may result causing property avoid tripping or snagging to reduce the damage, personal injury or death. - Page 8 INSTALLATION Recessed Installation: 4. Connect the fire feature to the inside of the 1. Prepare frame opening according to chart. fire unit. Frame opening is slightly larger than the fire unit. 5. Hang the glass face on the fire unit. Make certain that the hooks from the on the backside of the glass face are secured in all 4 slots on the fire unit.
-
Page 9: Operation
OPERATION OPERATION On the bottom of the unit is a main power switch. Switch this on to begin using the fireplace. Directly below the flame, on the right hand side are 3 small LED status lights and 3 buttons. Power Heat Backlight When all indicator lights are off, pressing on... -
Page 10: Service Parts
MAINTENANCE HF CBI SERVICE PARTS ITEM PHOTO COMMENTS PRINTED CIRCUIT BOARD CONTROLS LOW MFPCB1 VOLTAGE AND HIGH VOLTAGE FUNCTIONS MFTC1 LCD TOUCH CONTROL MFRR1 REMOTE CONTROL IR RECEIVER MF12VT1 TRANSFORMER MFHF12015 HEATER FAN 120 V 1500 WATTS... - Page 11 MAINTENANCE MFPHF HF HEATER 120 V 1500 WATTS MFSM120 SPINDLE MOTOR 120 V 50-60 HZ MFPHF36 LED LED LIGHT STRING HF36 MFPHF42 LED LED LIGHT STRING HF42 MFPHF60 LED LED LIGHT STRING HF60 MF PS1 POWER SWITCH MFR1 REMOTE CONTROL HFGLS36 GLASS FACE HF36 HFGLS42...
-
Page 12: Frequently Asked Questions
MAINTENANCE FREQUENTLY ASKED QUESTIONS Q. How do you program the remote control? A. The remote comes pre-programmed. No programming is necessary. Q. What distance can the remote be used from the fireplace? A. Optimal distance for the remote control is within 10 yards. Q. - Page 13 MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Fireplace is not plugged in to an A. Check plug electrical outlet B. Breaker tripped or outlet has no B. Reset breaker, test outlet for power power C. Turn main power switch to the C.
-
Page 14: Cleaning And Maintenance Instructions
MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A. Disconnect unit from power A. Wiring is loose source and inspect for loose Flame is not visible when connections unit is turned on B. Motherboard is defective B. Replace motherboard A. Disconnect unit from power A. - Page 15 MAINTENANCE NOTES...
- Page 16 © 2012 www.modernflames.com Please dispose of properly.
Need help?
Do you have a question about the HF36CBI and is the answer not in the manual?
Questions and answers