1 Safety Precautions 1.1. General Guidelines 1.3. Leakage Current Hot Check (See Figure 1) 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment 1. Plug the AC cord directly into the AC outlet. Do not use which are important for safety. These parts are marked by an isolation transformer for this check.
1.4. How to Discharge the Capacitor on Flash CON P.C.B. • This unit equipped with two pieces of capacitors as flash charging capacitors. "Either one of the capacitor discharging operation" makes discharging for others as well. CAUTION: 1. Be sure to discharge the capacitor on Flash CON P.C.B. 2.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).
2.3.2.3. How to Replace the Fuse A replacement fuse cover can be purchased from your local Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
Note: The lithium battery is a critical component. (Type No.: ML-421S/ZTK Manufactured by Energy Company, Panasonic Corporation) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
Page 8
Note: Above caution is applicable for a battery pack which is for DMC-FT4 and DMC-TS4 series, as well. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
5 devices) Panasonic’s test method is based on the above "MIL-STD 810F Method 516.5-Shock". However, the drop height was changed from 122 cm (4.0 feet) to 200 cm (6.6 feet) dropping onto 3 cm (0.10 feet) thick plyboard. This drop test was passed.
3.5. About IC9301 (COMPASS) [On the TOP FPC UNIT] When IC9301 is defects and necessary to be replaced, replace with whole TOP FPC UNIT as a unit. 3.6. General Description About Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
How to Define the Model Suffix (NTSC or PAL model) There are seven kinds of DMC-FT4/TS4, regardless of the colours. • a) DMC-FT4 (Japan domestic model.) • b) DMC-TS4P/PC • c) DMC-FT4EB/EF/EG/EP • d) DMC-FT4EE • e) DMC-FT4GN • f) DMC-TS4GD •...
3.7.2. INITIAL SETTINGS: After replacing the Main P.C.B., be sure to perform the initial settings after achieving the adjustment by ordering the following procedure in accordance with model suffix of the unit. 1. IMPORTANT NOTICE: Before proceeding Initial settings, be sure to read the following CAUTIONS. 2.
Page 13
[Only for "EG, EF, EB and EP" models : (VEP56129D is used as a Main P.C.B.)] When Main P.C.B. has just been replaced, the following model suffix list is displayed as follows. (Two pages in total) [CASE 2. Other than "After replacing Main P.C.B."] •...
Page 14
1) As for your reference, major default setting condition is as shown in the following table. Default setting (After "INITIAL SETTINGS") MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS DMC-FT4(Japan domestic model) NTSC Japanese Year/Month/Date DMC-FT4EB English Date/Month/Year DMC-FT4EE Russian Date/Month/Year DMC-FT4EF French Date/Month/Year DMC-FT4EG English...
Page 16
Note: *Above specification is for DMC-TS4P. Some of the specification may differ depends on model suffix. [1] Only for "EB/EF/EG/EP" models: 1). [Interface Digital:] • Data from the PC can not be written to the camera using the USB connection cable. [2] Others: 1).
6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery, the battery is pulled out) The error code is memorized to FLASH ROM when the unit has just before powered off.
Page 23
3. Error Code List The error code consists of 8 bits data and it shows the following information. Attribute Main item Sub item Error code Contents (Upper) Error Indication High 4bits Low 4 bits Check point (Lower) Detecting Part/Circuit device LENS Lens drive OIS 18*0...
Page 24
Attribute Main item Sub item Error code Contents (Upper) Error Indication High 4bits Low 4 bits Check point (Lower) Detecting Part/Circuit device HARD VENUS A/ Flash 28*0 0000 Flash charging error. STRB CHG Flash CON P.C.B./FPC IC6001-(AC16) signal line or Flash charging circuit FLASH FLASH 2B*0...
4. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode. Note: The error code can not be initialized. 6.2. ICS (Indication of additional Camera Settings when picture was taken) function 1.
Page 26
3. How to read 4. How to exit Simply, turn the power off. (Since ICS function is executed under the condition of temporary cancellation of "INITIAL SETTINGS",it wake up with normal condition when turn off the power.)
7 Troubleshooting Guide 7.1. Service and Check Procedures 7.1.1. Servicing flow • The following is the servicing procedure including assembly/disassembly process. • As for the air-leak test, refer to "7.2. Air-leak Test". < Note > Air-leak test (inspection) before taking service measure: •...
Page 28
7.1.2. Periodical maintenance (Packing replacement) flow • The integrity of the waterproof packings may decrease about 1 year, with use and age. (We recommend end-users to replace the waterproof packing at least once each year described in the operating instructions.) •...
Page 29
Replacing the waterproof packing • The location of waterproof packing are shown at right. (5 types, 8 packings in total) • Waterproof packings are supplied as Waterproof packing kit (Part No.: VUMG1978). < Note for replacement > • Do not touch the waterproof packings directly by the hand. •...
7.2. Air-leak Test Due to the waterproof performance retention, perform the air-leak test using Air-leak tester (Part No.:RFKZ0528) before/after servicing when disassembling and assembling the unit. *The Air-leak test before servicing is necessary to be performed to check whether the malfunction occurred due to air-leak or not. 1.
Measuring condition (For DMC-FT4, DMC-TS4) *Attach "L" size of absorption pad. [Exhaust Air] 5. Operate the measurement switch of the air-leak tester to exhaust air inside the product for 90 seconds. [Stand-by] 6. After a laps of 15 seconds, take a note (Record) that the pressure value indicated on the indication panel. [Measurement] 7.
2. Checking flowchart of GPS failure. The checking flowchart of GPS failure is as follows: Note: *Perform the GPS communication test, even if the repair being carried out is not related with GPS function. *The GPS function in this unit is performed communication between GPS module (Mic GPS FPC Unit) and VENUS (IC6001: on the Main P.C.B.).
Page 33
2. ABOUT EACH SENSOR 2.1. COMPASS 2.1.1. General description 2.1.2. Failure diagnosis of Compass. The Compass sensor unit is IC9301 which is located on TOP FPC unit. Since the IC9301 does not supply as a spare parts, replace as a TOP FPC unit if necessary. Settings/Condition: 1.
Page 34
2.2. ALTIMETER 2.2.1. General description 2.2.2. Failure diagnosis of Altimeter. The Altimeter sensor unit is IC9202 which is located on Main PCB. (It detects direction of gravitation.) Settings/Condition: 1.After performing the compass failure diagnosis, face down (the LCD side up) the camera unit, gradually. Diagnosis: 1.When the compass in the camera unit points same direction before and after above condition, the built-in altimeter unit works fine.
Page 35
2.3. BAROMETER 2.3.1. General description 2.3.2. Failure diagnosis of Barometer. The barometer sensor unit is IC9201 which is located on Main P.C.B. Settings/Condition: 1.After performing the altimeter failure diagnosis, take a note that the altimeter which is currently indicated on the LCD. Diagnosis: 1.
8.2. When Replacing the Main P.C.B. After replacing the Main P.C.B., be sure to achieve adjustment. The Maintenance software (DIAS) is available at "software download" on the "Support Information from NWBG/VDBG-AVC" web- site in "TSN system". 8.3. Service Position This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing. Table S1 Extension Cable List Parts No.
Page 40
9.3.2. Removal of Front Aluminum Case 9.3.4. Removal of Rear Case Unit Fig. D2 9.3.3. Removal of Rear Aluminum Case Fig. D4 Fig. D3...
Page 41
9.3.5. Removal of Lens Unit (with CCD) Note: (When Disassembling/Assembling) 1. When dust stuck, use air-Blower to blow off the dust. 2. Do not touch the surface of lens by your hand. 3. Use Lens Cleaning KIT; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.
Page 42
9.3.6. Removal of Main P.C.B. 9.3.7. Removal of Top Ornament Fig. D8 Fig. D7...
Page 43
9.3.8. Removal of Top Button Plate/Top 9.3.9. Removal of Battery Frame Unit Button Packing Fig. D10 Fig. D9...
Page 44
9.3.10. Removal of Top FPC Unit 9.3.11. Removal of Flash CON P.C.B. Fig. D11 Fig. D12...
Page 45
9.3.12. Removal of Battery Door Unit 9.3.13. Removal of MIC G FPC P.C.B. (Battery Door Packing) Fig. D13 Fig. D14...
10 Measurements and Adjustments 10.1. Introduction When servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced. Before disassembling the unit, it is recommended to back up the camera data stored in flash-rom as a data file. IMPORTANT NOTICE (After replacing the Main P.C.B.) After replacing the Main P.C.B., it is necessary to use the "DIAS"...
Page 49
10.2.2. Flash-Rom Data Backup When trouble occurs, it is recommended to backup the Flash-rom data before disassembling the unit. There are two kinds of Flash-rom data backup methods: [ROM_BACKUP (Method of Non-PC backup)] 1. Insert the SD-card into the camera. 2.
10.3. Details of Electrical Adjustment 10.3.1. How to execute the Electrical Adjustment It is not necessary to connect the camera to a PC to perform adjustments. "Flag reset operation" and "Initial setting operation" are required when carrying out the alignment, follow the procedure below. 10.3.1.1.
Page 51
10.3.1.3. Execute Adjustment 1. Perform step "10.3.1.1." to "10.3.1.2.", to reset the OIS flag status "F" (Set) to "0" (Reset). 2. Press DISPLAY button after Flag reset. OIS Adjustment screen is displayed on the LCD panel. (Refer to Fig.3-4) 3. Press the shutter button. The adjustment will start automatically.
Page 52
10.3.2. Adjustment Specifications The following matrix table shows the relation between the replaced part and the Necessary Adjustment. When a part is replaced, make sure to perform the necessary adjustment(s) in the order indicated. The table below shows all the information necessary to perform each adjustment.
IMPORTANT NOTICE (After replacing the Main P.C.B.) After replacing the MAIN P.C.B., make sure to perform the "INITIAL SETTINGS" first, then release the "INITIAL SETTINGS" in order to proceed the electrical adjustment. Note: 1. If electrical adjustment or data re-writing is executed before "INITIAL SETTINGS", suffix code list is never displayed, and it cannot be chosen suitable suffix code.
11 Maintenance 11.1. Cleaning Lens and LCD Panel Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: The Lens Cleaning KIT;...
Page 84
Model No. : DMC-FT4/TS4 MIC G FPC P.C.B. (Foil Side)
Page 85
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C1001 F1H0J106A009 C.CAPACITOR CH 6.3V 10U C1002 F1J1A106A043 C.CAPACITOR CH 10V 10U C1003 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C1004 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C1010 F1J1A106A043 C.CAPACITOR CH 10V 10U...
Page 86
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C4010 F1H1A225A051 C.CAPACITOR CH 10V 2.2U C4011 F1H0J2250008 C.CAPACITOR CH 6.3V 2.2U C4012 F1H1A225A051 C.CAPACITOR CH 10V 2.2U C4013 F1H0J2250008 C.CAPACITOR CH 6.3V 2.2U C4014 F1G0J1050007 C.CAPACITOR CH 6.3V 1U...
Page 87
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks C7108 F1G0J1050007 C.CAPACITOR CH 6.3V 1U C7109 F1G1H4710004 C.CAPACITOR CH 50V 470P C7110 F1G1H4710004 C.CAPACITOR CH 50V 470P C8003 F1G1H220A565 C.CAPACITOR CH 50V 22P 1 [PAVCX] C8004 F1G0J1050007...
Page 88
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks FP9005 K1MN04BA0162 CONNECTOR 4P FP9006 K1MY18BA0370 CONNECTOR 18P FP9007 K1MY39BA0235 CONNECTOR 39P FP9008 K1MY15BA0235 CONNECTOR 15P IC1001 C0DBAYY01047 1 E.S.D. IC1090 C0DBAYY00946 1 E.S.D. IC1110 C0DBGYY00821 1 E.S.D.
Page 89
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks LB9605 J0JCC0000412 FILTER M9901 L0CBAA000014 MICROPHONE UNITS P8002 K4ZZ04000060 CONNECTOR 4P 1 [PAVCX] P9007 K1NA09E00098 SD CARD CONNECTOR Q1620 B1CFJC000009 TRANSISTOR 1 E.S.D. Q8001 B1JBLP000038 TRANSISTOR 1 E.S.D.
Page 90
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks R6060 ERJ2RKF1000 M.RESISTOR CH 1/16W 1K R6061 ERJ2RKF1000 M.RESISTOR CH 1/16W 1K R6062 ERJ2RKF1000 M.RESISTOR CH 1/16W 1K R6063 ERJ2RKF1000 M.RESISTOR CH 1/16W 1K R6071 ERJ2GEJ102X M.RESISTOR CH 1/16W 1K...
Page 91
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks R9619 ERJ2GEJ202 M.RESISTOR CH 1/10W 2K R9620 ERJ2GEJ202 M.RESISTOR CH 1/10W 2K R9621 ERJ2RHD682X M.RESISTOR CH 1/10W 6.8K RX6001 EXBN8V103J RESISTOR ARRAY 1/32W 10K RX6002 EXBN8V101JX RESISTOR ARRAY 1/32W 100 RX6003 EXBN8V101JX...
Page 92
Model No. : DMC-FT4/TS4 Frame and Casing Section...
Page 93
Model No. : DMC-FT4/TS4 Packing Parts and Accessories Section (1)
Page 94
Model No. : DMC-FT4/TS4 Packing Parts and Accessories Section (2)
Page 95
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VKM8987 SIDE ORNAMENT R VEP58155A FLASH CON P.C.B. 1 (RTL) E.S.D. [PAVCX] VGQ0W23 TOP FPC SHEET VYK4L63 REAR CASE(1) U VGQ0U27 DPR SHEET VGQ0W11 LENS CUSHION VYQ7177 LCD UNIT...
Page 96
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VMS8149 BATT LOCK SHAFT 1 [PAVCX] VGQ0S50 BARRIER TAPE 1 [PAVCX] VGQ0V50 DPR SHEET VGU0H84 REAR BUTTON DISPLAY 1 [PAVCX] VGU0H85 REAR BUTTON Q.MENU 1 [PAVCX] VGU0H86 REAR BUTTON MENU SET...
Page 97
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VQT4E00 BASIC O/I (ENGLISH) 1 EB VQT4E01 BASIC O/I (RUSSIAN/UKRAINIAN) 1 EE VQT4E02 BASIC O/I (ENGLISH/CHINESE(TRADITIONAL)) 1 GC,GH VQT4E03 BASIC O/I (ARABIC/PERSIAN) 1 GC VQT4E04 BASIC O/I (VIETNAMESE) 1 GC...
Page 98
Model No. : DMC-FT4/TS4 Parts List Ref. Safety Part No. Part Name & Description Q'ty Remarks VHD1759 SCREW 1 [PAVCX] VUMG1978 WATERPROOF PACKING KIT 1 (Including in "P-1 to P-8") ----- O-RING 1 (Included in "VUMG1978") ----- O-RING 1 (Included in "VUMG1978") ----- O-RING 1 (Included in "VUMG1978")