Locking Features; Clean Cycle - Hot Spot SORRENTO Owner's Manual

READY
SET
F1
F2
READY
filter cycle will resume. The blinking filter Icon indicates that the filter cycle timer is still counting, but the cycle has been temporarily interrupted.
READY
NOTE: The interrupted time of a filter cycle is not extended after the filter cycle resumes. Power interruptions of the spa will reset the filter cycle to
the default 1.5 hour cycle time (F1) and begin 10 minutes after spa regains power.

CLEAN CYCLE

READY
SET
F1
F2
READY
SLEEP MODE
READY READY
activation during quiet evening hours.
I I m m p p o o r r t t a a n n t t : : Power-up of the spa starts the F1 default sequence. In order for the sleep mode to work in the evening hours, the spa must be
powered up in the early morning hours. The Sleep Mode will always be active the 6-12 hours between the end of (F2) and the begining of (F1)
depending on how the filter cycle program is set.
Note: If temperature drops below 80 degrees, heater will automatically activate to prevent spa from freezing.
To activate Sleep Mode feature, press and hold Temp Up (▲) & Temp Down (▼) buttons together for 3 seconds. This will activate the feature and
override the normal temperature demand. When these buttons have been engaged, a Moon & Stars icon (Sleep Icon) will appear in the display of
the control panel, indicating this feature has been activated. To deactivate this feature, simply press and hold Temp Up (▲) & Temp Down (▼)
buttons together for 3 seconds once again.

LOCKING FEATURES

The locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the control panel by a specific combination of buttons. Once
enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if power is disconnected from the spa
and soon thereafter reapplied (such as a power outage), the lock will remain in place.
SPA LOCK
READY
READY READY
READY READY
READY
TEMPERATURE LOCK
READY
READY READY
READY
READY
READY
To deactivate the Temperature Lock, press SET button followed by Temp Up (▲) button until
READY READY
SET
F1
F2
SET
F1
F2
READY
READY
READY
READY
READY
READY
The Clean Cycle has been provided as a convenient timer for water maintenance. When the Clean Cycle is initiated,
SET
the Jet pump will activate in high speed. The jet pump icons will flash on and off until the cleaning cycle is complete.
F1
The total cleaning cycle time is ten minutes. If the clean cycle does not engage, make sure the SPA LOCK is F2
deactivated. To activate the Clean Cycle, press the SET button followed by the JETS button.
READY
READY
The Sleep Mode operation is a feature that minimizes pump operation during quiet evening hours. For example, if
READY
Filter Cycle 1 (F1) is set to activate at 8:00 a.m., by default, Filter Cycle 2 (F2) will activate at 8:00 p.m. (12 hours later).
During 8:00 p.m. to 8:00 a.m., if the spa should call for heat, the pump and heater will activate to heat the spa under
normal temperature demand. However, when in Sleep Mode, should the spa call for heat, the pump and heater will
be suspended after Filter Cycle 2 (F2) until the activation of Filter Cycle 1 (F1), at 8:00 a.m. to minimize pump
SET
F1
F2
READY
The Spa Lock feature deactivates all of the functions of the control panel. It is generally used to prevent unwanted
SET
use of the spa.
F1
To activate the Spa Lock, press SET button followed by Temp Down (▼) button until
F2
SET
To deactivate the Spa Lock, press SET button followed by Temp Down (▼) button until
F1
F2
The Temperature Lock feature deactivates the temperature control function from the control panel. All other functions
READY
on the control panel will operate normally. Temperature Lock is most often used by those who do not want others to
change the set temperature of the spa water.
READY
To activate the Temperature Lock, press SET button followed by Temp Up (▲) button until
F1
READY
F1
SET
F1
F2
SET
F1
F2
READY
SET
F1
F2
READY
READY
F1
READY
SET
READY
SET
F1
F2
F1
F2
READY
READY
F1
READY
SET
F1
F2
READY
READY
READY
READY
READY
Page 15
is displayed.
SLOC
is no longer displayed.
SLOC
TLOC
is no longer displayed.
TLOC
is displayed.