Advertisement
Before you start...
Read the electrical
and carpentry
instructions.
Proper installation is your responsibility. A
qualified technician
should install this oven.
Make sure you have everything
necessary for
correct installation. It is the responsibility of the
installer to comply with the installation
clearances
specified on the serial/rating
plate. The serial/rating
plate can be found
behind the door (double oven models -
upper oven) on the oven frame.
Check location where the built-in oven will be
installed. The location should be away from
strong draft areas, such as windows, doors,
and strong heating vents. The built-in oven
should be located for convenient
use in the
kitchen.
30" Single oven
Cablnet door
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Dimensions given are for
a built-in oven sitting on a contact
surface
2-3/4" below the open oven door height. The
contact
surface must be solid and level and
flush with the bottom of the cabinet opening.
The recessed installation area must provide
complete
enclosure around the recessed
portion of the oven.
ALL OPENINGS IN THE WALL OR FLOOR WHERE
THE BUILT-IN OVEN IS TO BE INSTALLED MUST BE
SEALED.
Electrical ground is required. See "Electrical
requirements."
Do Not install single oven in a base cabinet
with a countertop
above it.
"Note:
There must be
i....... 1" mln. between bottom
ot c&lnet
door and top
of oven console.
I-- Oven control
Do Not seal
oven to
cabhets.
31-l/6-
recessed
oven helght
recessed
\
depth
'+.Y~;
open Is 36" horn floor.
I
The oven support surface must be flush with
the bottom of the cabinet opening.
I
Important: Observe all governing codes
ordinances.
Electrical Shock Hazard
It is the customer's responsibility:
l
To contact a qualified electrical
installer.
l
To assure that the electrical
installation is
adequate
and in conformance
with
National Electrical Code, ANWNFPA
70 - latest edition", and all local codes
and ordinances.
Failure to do so could result in fire,
electrical shock or other personal injury.
Personal Injury Hazard
Securely fasten oven to cabinet using the
screws provided (4 screws for a single
oven or 8 screws for a double oven).
Failure to do so could cause the oven to
move or tip during use and result in
personal injury.
30" Double oven
-
...>>>
. . . . . . * . . . . . . . y
i-h
A I _,.
"'Note:
There must be
$ . . . . ..- _ 1" min. befwa
b&m
of cablnet door and top
of oven console.
-.:;...
. ..-..
kit
"k Oven control
console
1
c
rC--
\
\
\
\
\
.
Do Not seal
oven to
cabinets.
[
I
1
5&7j16"-
Electrical supply
:
I Junctlon box
~'eS
III
)
57-316" -
overall
helght
See Note."'
j
&k3"
my. below . oveni'zht
Ill
_ ,zc i
support surtace
.1
Cabinet Damage
Do Not block the oven vent.
Blocking the oven vent may cause cabinet
damage and poor baking performance.
Mobile home installation
The installation of this oven must conform to
the Manufactured
Home Construction
and
Safety Standards, Title 24 CFR, Par-t 3280
(formerly the Federal Standard for Mobile
Home Construction
and Safety, Title 24, HUD
Part 280) or when such standard is not
applicable,
the Standard for Manufactured
Home Installation 1982 (Manufactured
Home
Sites, Communities and Setups), ANSI 2225.1-
1984, or latest edition, or with local codes.
A four-wire, power supply cord must be used
in a mobile home installation. The appliance
wiring will need to be revised. See "Electrical
requirements, fl Figure 3, Panel B.
Copies of the standards listed may be
obtained
from:
l
National Fire Protection Association
Batterymarch
Park
Quincy, Massachusetts 02269
brn floor.
I
i
Ill
-
Panel A
Advertisement
