Panasonic Lumix DMC-FH2P Service Manual page 39

Service Manual
Diagrams and Replacement
Parts List
Digital Camera
Model No.
DMC-FH2P DMC-FH2GF
DMC-FH2PC DMC-FH2GH
DMC-FH2PR DMC-FH2GK
DMC-FH2PU DMC-FH2GN
DMC-FH2GA DMC-FH2GT
DMC-FH2GC DMC-FS16EB
DMC-FH2GD DMC-FS16EE
Vol. 1
Colour
[DMC-FH2] [DMC-FS16]
(S)...........Silver Type (except P/GD) (S)...........Silver Type (except EF)
(K)...........Black Type (K)...........Black Type
(P)...........Pink Type (except PC/GT) (P)...........Pink Type (except EE)
(R)...........Red Type (except PR/GD/GT) (R)...........Red Type
(A)...........Blue Type (except PR/GT) (A)...........Blue Type
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash P.C.B. .......................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S3.2. Flash/Top Block Diagram ...................................................... S-4
S4. Schematic Diagram .................................................................. S-5
S4.1. Interconnection Diagram ....................................................... S-5
S4.2. Top Schematic Diagram ........................................................ S-6
S4.3. Flash Schematic Diagram ..................................................... S-7
S4.4. CCD Flex Schematic Diagram .............................................. S-8
S5. Print Circuit Board .................................................................... S-9
S5.1. Top P.C.B. ............................................................................. S-9
S5.2. Flash P.C.B. ........................................................................ S-10
S5.3. CCD Flex P.C.B. .................................................................. S-11
DSC1102026CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
3.The voltage being indicated on the schematic diagram is measured in
DMC-FS16EF
4.Although the voltage and waveform available on here is measured with standard frame,
DMC-FS16EG
DMC-FS16EP
5.The voltage being indicated here may be include observational-error (deviation) due to
DMC-FS14EB
DMC-FS14EE
DMC-FS14EG
6.Use the parts number indicated on the Replacement Parts List .
DMC-FS14EP
7.Indication on Schematic diagrams:
[DMC-FS14]
(K)...........Black Type
(R)...........Red Type (only EB)
S6. Replacement Parts List .......................................................... S-13
S7. Exploded View ....................................................................... S-18
S7.1. Frame and Casing Section.................................................. S-18
S7.2. Packing Parts and Accessories Section (1) ........................ S-19
S7.3. Packing Parts and Accessories Section (2) ........................ S-20
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
when the TP (Test Point) indicated as "
"Standard-Playback" mode when there is no specify mode is mentioned.
it may be differ from actual measurement due to modification of circuit and so on.
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
Circuit name being connected.
OFTR FEP
Name of Signal
S-1
HAVE THE SPECIAL CHARACTERISTICS
" mark.
This signal is connected
to the FEP schematic diagram.