1. Manuals
  2. Brands
  3. On-Q Manuals
  4. Network Router
  5. 364732-01
  6. User manual

On-Q 364732-01 User Manual

4 port router/switch
Hide thumbs Also See for 364732-01:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
Enlarged version
Innovations in Home Living.
301 Fulling Mill Road, Suite G
©Copyright 2004 by OnQ Technologies,
Middletown, PA 17057
Inc All Rights Reserved.
(800)-321-2343
www.onqhome.com
4 PORT ROUTER/SWITCH
(P/N 364732-01)
USER'S GUIDE
1307741 REV.O
Innovations in Home Living.
301 Fulling Mill Road, Suite G
©Copyright 2004 by OnQ Technologies,
Middletown, PA 17057
Inc All Rights Reserved.
(800)-321-2343
www.onqhome.com

Advertisement

Table of Contents
loading

Related Manuals for On-Q 364732-01

Summary of Contents for On-Q 364732-01

  • Page 1 4 PORT ROUTER/SWITCH (P/N 364732-01) USER’S GUIDE 1307741 REV.O 301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, 301 Fulling Mill Road, Suite G ©Copyright 2004 by OnQ Technologies, Middletown, PA 17057 Inc All Rights Reserved. Middletown, PA 17057 Inc All Rights Reserved.
  • Page 2 Appendix A Specifications IEEE 802.3 10Base-T Ethernet Standards IEEE 802.3u 100Base-TX Fast Ethernet IEEE 802.3x Flow Control WAN: One 10/100Mbps RJ-45 port for Cable/DSL Ports Modem LAN: Four 10/100Mbps switched ports UTP Category 3 or better (10Base-T) Cabling type UTP Category 5 or better (100Base-TX) IP, NAT, ARP, ICMP, DHCP client/server, PPPoE, Protocols Supported PPP, PAP, CHAP, NTP, HTTP, TFTP.
  • Page 3 168.95.192.1 –w 5000 or turning the On-Q Home 4 Port Router/Switch off and on, the user is encouraged C:\> PING www.yahoo.com –w 5000 to try to correct the interference by one or more of the following measures: If successful, you are connected to the Internet.

  • Page 4: Table Of Contents

    3) The DNS server IP addresses should match the DNS server IP TABLE OF CONTENTS addresses set in the device. Introduction For Win NT and Win2000, go to “Start” ”Programs” ”Accessories” ”Command Prompt” to II. Product Overview open the Command Prompt. Type in IPCONFIG /ALL and A.

  • Page 5: Introduction

    I. Introduction The On-Q Home 4 Port Router/Switch is an integrated Internet IP sharing device with a built-in 4-port 10/100Mbps Fast Ethernet switch. Its superb throughput as high as up to 80Mbps between Internet and LAN makes it the perfect solution to connect a small group of PCs to a high-speed broadband Internet connection (see Figure 1).
  • Page 6 TCP/IP connections, but can be used to get the current IP address assignments. For Win 95/98/ME, from Windows, go to Start, click Run, enter WINIPCFG, and click OK. Figure 13 Figure 14 displays the adapter address and current TCP/IP address. NOTE: At the “Ethernet Adapter Information”, select the correct Ethernet adapter that is installed in this computer.

  • Page 7: Product Overview

    To check the Internet connection status, open B. Components Included the browser to start the Web configuration, select Network The On-Q Home 4 Port Router/Switch includes the following parts: • Router/Switch Module Status WAN IP Status. Check if Link Status displays “Connect successfully”.

  • Page 8: Detailed Physical Description

    D. On-Q Home 4 Port Router/Switch Detailed Physical Description VI. Troubleshooting The following information describes the physical characteristics of the On-Q Home Router/Switch: A. Contact Information If you are unable to locate a solution here, please access our website at 1.
  • Page 9 2. Firmware Upgrade (see Figure 12) Download the latest firmware from Technical Support at On-Q Home and save the file on the hard drive. b. Make sure all computers in the network are off; or connect the Broadband Router directly to the PC that has the new firmware.
  • Page 10 V. Advanced Setup A. Management On this management screen (see Figure 10), you can 1. Change Administrator’s password: change the password for the device. This page intentionally otherwise blank. Figure 10 Change Administrator’s password New Password Enter the new password. Confirm New Re-enter the new password for confirmation.

  • Page 11: Installation

    DHCP Server Do not distribute IP Check this radio button to disable this device The On-Q Home 4 Port Router/Switch is best installed during new address to local from distributing IP Addresses (DHCP Server construction in two steps; at “rough-in” after the Electricians are done,...
  • Page 12 NOTE: Use proper tools and standard TIA 568A rules to prep and IP address to a computer (according to the network adapter’s MAC terminate the CAT5e cable, such as the On-Q Home CAT5 Cable address) and this computer becomes the only one able to request that Stripper (P/N 363292-01) and the On-Q Home EZ RJ45 Crimp Tool IP address.

  • Page 13: Configuration

    Static IP Enter the IP address provided by your ISP. Address: The On-Q Home 4 Port Router/Switch is typically configured in one of two ways; Static DNS Enter the primary and secondary DNS (1) From a portable PC connected through one of the Local Switch Ports on the Server addresses provided by your ISP.

  • Page 14: Logging On To The Router/Switch

    in that subnetwork is 192.168.1.254, so your PC’s Ethernet Card can be temporarily assigned an IP address, (like 192.168.1.10), on that same Device Information subnetwork to talk to and configure the Router/Switch. Giving the PC a Adapter This field is grayed out, because the Adapter Address specific IP address is also called assigning it a Static IP address, as compared Address is not supposed to be entered randomly.

  • Page 15: Internet Port Setup

    PPPoE (DSL dynamic Mode) NOTE: At the setup home page, the tabs at the top of the page are provided to link you directly to the desired setup screen. You can If this mode is selected (see Figure 8) and settings are saved, this select Internet Port, Local Port, Advanced Setup (Management, Router/Switch will be connected to the Internet over an always- Virtual Server, Packet Filter, Static Route, Dynamic DNS),...

  • Page 16: Cable Modem Setup

    1. CATV dynamic Mode (Cable Modem) Domain For example: yourcompany.com. The maximum input Selecting this mode (see Figure 7) enables you to obtain Name for this field is 32 alphanumeric characters and it is dynamic IP address from your ISP via DHCP support. Once the IP address is obtained, you can access the Internet.

Table of Contents