Table of Contents
Related Manuals for Genie EZPZ
Summary of Contents for Genie EZPZ
-
Page 1: User Manual
EZPZ IP Kit (Ver. 1.1) H.264 Video Compression Network Video Recorder & IP Camera User Manual About this User Manual Before installing, or operating the unit, please read this manual thoroughly and retain it for future reference. -
Page 2: Safety Precautions
Safety Precautions Explanation of Graphical Symbols This symbol indicates the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This symbol indicates the presence of uninsulated ”dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. - Page 3 These precautions must be followed for safety reasons Warning Do not use if the unit emits smoke, strange sounds, or odours are emitted. Make sure the power cable is not damaged. Make sure there is no dust accumulation on the power plug or the outlet. ...
-
Page 4: Product Components
The package contains the main unit and its components. When you purchase the unit, please check to ensure the components specified below are included. EZPZ NVR Unit 4x EZPZ IP Camera (PoE) Remote Control Battery1.5V (2x AAA) Quick User Guide Mouse for NVR Software &... -
Page 5: Basic Mouse Functions
Mounting the Hard Disk Drive 1. Remove the screws and the top cover as shown below. 2. Mount the HDD into the mounting bracket. 3. Insert the HDD bracket and mounting screws. 4. Connect the HDD SATA and power cable. Basic Mouse Functions ①... - Page 6 Specification Please note that specifications and unit exterior design are subject to change without prior notification MODEL EZPZ NVR IP Camera Input Max. Bit Rate 20Mbps Video Resolution Maximum 1920 x 1080 Main Monitor VGA and HDMI Output Sub Monitor...
- Page 7 Weight Unit Weight (Gross Weight) Approximately 6Kg Dimension Unit Dimension (W x H x D) 340mm x 262mm x 63mm MODEL EZPZ IP Camera Feature 2.1MegaPixel, IR Vandal Dome Sensor 1/2.8" 2MP Progressive Sensor Shutter Speed 1/8 ~ 1/30,000 sec Minimum Illumination 1 Lux @ F1.2 Without DSS...
- Page 8 Image Adjustment Fixed Motion Detection Sharpness Fixed D Noise Reduction Fixed Flip/Mirror Fixed Day & Night Auto Interface 10/100 Base-T Maximum Simultaneous Users 4x Users Network Web Browser Internet Explorer 10 Web Language English Compression Dual Streaming (H.264/H.264) Maximum Video Resolution 1920 x 1080 Video Maximum Frame Rate...
-
Page 9: Table Of Contents
4. Setting up the NVR ......................... 21 4-1. Setup – Main Live Screen ......................21 4-1-1. Setup – MENU TREE ......................22 4-2. Setup – EZPZ IP Camera ......................24 4-2-1. SCAN Menu ..........................26 4-3. Setup – DISPLAY ........................26 ... - Page 10 6-3. Transferring Still Images or Video from the ARCHIVE List ............56 6-4. Playback of Backup Video ......................57 7. Network Access Using the EZPZ Viewer ................... 58 7-1. Overview ............................ 58 7-2. PC Requirements ........................58 ...
-
Page 11: Main Features
1. Main Features Automatic IP Camera Detection and Connection (Plug & Play) Easy Record, Setup and Backup Easy Search by Thumbnail Preview Easy IP Camera Setup Covert Camera Operation Provides Enhanced Security and Administrator Control ... -
Page 12: Setting Ntp (Network Time Protocol)
2. Go to SETUP > SYSTEM > DATE & TIME SETUP 3. Select ON from the DAYLIGHT SAVINGS dropdown menu. 2-3. Setting NTP (Network Time Protocol) 1. SETUP > SYSTEM > NTP SETUP > ON... -
Page 13: Quick Installation
NOTE: If you want the unit to automatically synchronise to the local time, the Time Zone must be set to your local time zone. 2-4 QUICK INSTALLATION Quick installation Menu for EZPZ NVR and EZPZ IP Camera (Right-Click on the Main Screen) 2.4.1 Helps Users to Setup the NETWORK Settings (Using an Internet Connection) - Page 14 IP address. It allows using a dynamic IP address to be associated with a static domain name and associates a dynamic IP address with a static domain name. Click Finish to save the setup. ④ 2.4.2 Helps Users to Setup the EZPZ IP Camera Settings...
-
Page 15: Poe Port Setup
① Select the Channel to configure. ② Select the Camera Manufacturer and then click on the scan button; this scans the network for any cameras from that particular manufacturer. ③ Select the desired Camera from the list, and then click on Register. ④... - Page 16 NOTE: With the EZPZ IP Kit, DO NOT USE a router connection to connect an IP Camera. The NVR will not be able to find the camera, or connect to it. The LAN Port can be connected to a router, but not the PoE Ports.
-
Page 17: Ip Camera Setup (Through Web Viewer Page)
2-6 IP Camera Setup (Through Web Viewer Page) EZPZ IP allows remote access to the IP Cameras through the "IP Camera Setup" menu in the Web Client Viewer. ① Click the right mouse button ② Select “IP Camera Setup”. ③... -
Page 18: Front And Rear Panels
3. Front and Rear Panels 3-1. Front Panel The following information describes the front panel controls. ① LED light is ON when power is applied to the system. POWER: ② LED light is ON when the system is recording video data. HDD: ③... -
Page 19: Remote Control
USB Port USB Terminal for Video Export or Firmware Upgrade ETHERNET RJ-45 Connector for LAN Connection, used for Internet Connection. SENSOR IN 4x Connectors for Sensor Device Connection. ALARM OUT 1x Connector for Alarm Device Connection. Provides Simple ON/OFF Switching Using Relay. 0.5A/125V, 1A/30V RS-485 RS-485 Control Terminal (D+, D-) - Page 20 SETUP: To open the SETUP menu. ⑩ Direction Buttons: To move between menu items or to select a channel. ⑪ ⑫ SEQ: To start auto sequencing the screen in full screen mode (Toggle). BACKUP: To start a Backup operation in Live or playback mode ⑬...
-
Page 21: Setting Up The Nvr
To enter the Setup Menu, click the right mouse button and select SETUP from the submenu, or press the Setup button on the remote control. When the EZPZ NVR prompts you with the LOG-IN window, enter the PASSWORD using the virtual keyboard or the remote control. The factory default password is 1111. It’s highly recommended you assign... -
Page 22: Setup - Menu Tree
4-1-1. Setup – MENU TREE IP CAMERA – CHANNEL VENDOR SCAN PORT WEB PORT PROTOCOL DISPLAY – – OSD CONTRAST – SEQUENCE – SEQUENCE DWELL TIME – CHANNEL NAME COVERT – VIDEO OUTPUT RECORD – CHANNEL RECORDING SENSOR RECORDING PRE RECORD POST EVENT RECORD... - Page 23 STORAGE – OVERWRITE – DISK FORMAT – DISK INFO – RECORDING LIMIT RECORDING LIMIT DAYS SYSTEM – NVR-ID – DESCRIPTION – LANGUAGE – DATE FORMAT – SET DATE & TIME TIME DISPLAY FORMAT TIME ZONE DAYLIGHT SAVING SET DATE & TIME –...
-
Page 24: Setup - Ezpz Ip Camera
LOAD DEFAULT – LOAD FACTORY DEFAULT – SOFTWARE UPGRADE 4-2. Setup – EZPZ IP Camera Press the SETUP button and enter the password. The setup menu is displayed as picture below. Item Description CHANNEL To manually connect each camera, click on the... - Page 25 Login box pops up (Enter the ID and Password of IP Camera). VENDOR Select the Brand of Camera. SCAN Automatically search the network for EZPZ IP Cameras. Enter the IP Address of the Camera. PORT Enter the camera stream Port Number (the default is 554)
-
Page 26: Scan Menu
4-2-1. SCAN Menu NVR and IP Cameras connected to the same Network are discovered by Search (VENDOR Only) Figure 4.2.1.1 IP CAMERA Setup Screen (Vendor Only) ① Select the specific manufacturer of the IP Camera and then click on the Scan button ②... - Page 27 Table 4.3.1. Menu Items in DISPLAY Setup Screen Item Description Enable/disable On-Screen Display. OSD CONTRAST Set the visibility level of the On-Screen Display (OSD 50~100) SEQUENCE Enable/disable sequential display of video in full screen mode. SEQUENCE Set the dwell time of each, single channel display in sequential display DWELL TIME mode (3~60 seconds) CHANNEL...
-
Page 28: Setup - Record Mode
4-4. Setup – RECORD Mode In the SETUP menu, select the RECORD tab and the RECORD menu appears, as pictured below. Navigate through the menu items using the mouse, or the buttons on the remote control, and change the value of the menu items. Figure 4.4.1. -
Page 29: Recording Schedules
4-4-1. Recording Schedules To setup a recording schedule, select SCHEDULE in the RECORD menu. Navigate through the items using the mouse or the remote control buttons. Select CHANNEL > select NONE, CONTINUOUS, MOTION or SENSOR > HIGHLIGHT AREA To copy a schedule to a different channel, select the channel from the COPY SCHEDULE menu. Figure 4.4.1.1. -
Page 30: Setup - Device Mode
4-5. Setup – DEVICE Mode In the SETUP menu, select the DEVICE tab and the device menu appears, as pictured below. Navigate through the menu items using the mouse, or the buttons on the remote control, and change the value of the menu items. -
Page 31: Setup - Storage Mode
SENSOR Select sensor number from 1 to 4 TYPE Set the type of sensor for the specified channel. Options are: OFF, N/O (normally open) and N/C (normally closed). IEE 802.3af POE PSE (Power Sourcing Equipment) Status Monitoring Menu STATUS 4-6. Setup – STORAGE Mode In the SETUP menu, select the STORAGE tab and the STORAGE menu appears, as pictured below. -
Page 32: Setup - System Mode
DISK FORMAT Once clicked, the user is asked to confirm the formatting of the Hard Drive. After confirming, the EZPZ NVR reboots, and the format sequence loads. Caution: It’s recommended you archive any data you may need in the future before formatting the hard drive. - Page 33 Table 4.7.1. Menu Items in SYSTEM Setup Screen Item Description NVR ID NVR System ID Setup (Letters and Numbers Only) DESCRIPTION Press the button to view the system information. (Software Version, Storage Size, IP Address, MAC Address and DDNS Status) LANGUAGE Select the display language using the mouse or the remote control.
- Page 34 ONCE – Synchronises time only once. NTP will not synchronise unless the Connection Mode is changed. EZPZ NVR sends an E-MAIL Notification when the NTP server time is faster than the system time; with the message shown below. “NTP server time is faster than the system time.
- Page 35 (Allows the user to set EVENT NOTIFICATION ON or OFF) HEALTH CHECK / RESTART / SHUTDOWN / PANIC RECORD Enable Email notification in the event a problem occurs with the EZPZ NVR. ALARM-IN – Enable Email notification when the camera detects sensor input.
-
Page 36: Setup - Security Mode
• NETWORK: Enable/Disable access to Network. • Selected Checkbox: The EZPZ NVR asks for a password when the chosen function is selected for all users. Blank Checkbox: The NVR will not ask for a password when the chosen function is... - Page 37 ADMIN, USER1, USER2, USER3: Selected Checkbox: The user can access the function. Blank: Means the user cannot access the function. USER NAME Change the name of USER1, USER2 and USER3. Click “ENTER” after re-naming. USER Options are ADMIN, USER1, USER2 and USER3. PASSWORD Select USER PASSWORD using the mouse or the buttons on the remote control and press the SEL button.
-
Page 38: Setup - Network Mode
Set the Port for sending audio data via the network. Default is 5446 and AUDIO PORT must be the next number to the NVR Port (i.e. EZPZ NVR PORT + 1). WEB PORT Enter the port number for connection using web. Default is 80. -
Page 39: Network Port And Web Port
To access the EZPZ NVR beyond a router (firewall), you must open the correct TCP ports for live/playback streaming, commands, remote backup and audio streaming. If these ports are not opened properly, you can’t access the NVR beyond a router. -
Page 40: Ddns
IP ADDRESS: The fixed IP address of the EZPZ NVR. • SUBNET MASK: The subnet mask. • GATEWAY: The IP address of the Gateway. • DNS (PRIMARY) The primary address of Domain Name Server • DNS (SECONDARY): The secondary address of Domain Name Server •... -
Page 41: Setup - Config Mode
Item Description SAVE SETUP User can save the current configuration (Setting Values) of the EZPZ NVR to TO A USB a USB flash drive. Plug in the USB flash on the front panel and press the button to start the saving process. -
Page 42: Firmware Upgrade
4-10-1. Firmware Upgrade In order to upgrade, the firmware upgrade file must first be downloaded and copied into the USB memory drive. Create a new folder in the USB memory drive and name it “upgrade”. Copy the firmware upgrade file “xxxxxx.bin”... -
Page 43: Remote Firmware Upgrade
Users can upgrade the firmware via the Network as follows: 1. Go to the Remote Setup Menu on the EZPZ Manager or the Web Viewer. 2. Enter the Admin password. Only the Admin User can connect to the remote Setup Menu. -
Page 44: Live, Search And Playback
3. Go to the Remote Upgrade Menu and you can see the current F/W version. To upgrade to a new F/W level, insert the F/W in your PC and press the UPGRADE button. 4. You will see the following progress bar, and it should take around 3 minutes to upgrade. 5. - Page 45 Figure 5.1.1. Live Screen and Quick Installation Window Table 5.1.1. Status Indicator Icons in Live Viewing Screen Icon Description Power On/Off button. Lock/Unlock Setup button. Setup button. Click this button to go to the Setup Menu. Click the AUDIO icon when you want to activate the Audio (using a mouse) Search button.
- Page 46 Displays the amount of recording stored on the hard disk from 0-99%. Indicates that the HDD is recycled. Continuous recording in progress. Manual recording in progress. To set the Manual recording mode, press the Record button on the front panel. Motion alarm recording in progress.
- Page 47 Figure 5.1.2. Quick Installation Window Table 5.1.2. Menu Items in Quick Installation Window Icon Description QUICK Enter Quick Installation mode. INSTALLATION DISCONNECT Select this option to disconnect/connect from IP Camera. SETUP Setup button. Click this button to go to the Setup Menu. AUDIO MUTE Select this option to mute Audio on all channels.
-
Page 48: Ptz Control
Press ESC to return to the main menu 5-2. Digital Zoom in Live and Playback Screen EZPZ NVR series supports a Digital Zoom feature during Live and Playback modes. 1. Double click the target channel. 2. Click the left mouse button and drag to make a rectangular shape. -
Page 49: Search Screen
5-3. SEARCH Screen To enter the Search Screen menu, select the SEARCH menu on the screen using the mouse or press the SEARCH icon on the Live Screen. Figure 5.3.1. Search Screen There are 7 Search Menu options, Quick SEARCH, TIME LINE (Calendar), EVENT, GO TO FIRST TIME, GO TO LAST TIME, GO TO SPECIFIC TIME, ARCHIVE LIST, and LOG LIST. -
Page 50: Time Line Search
Figure 5.3.1.1. Play Mode Screen 1. When the Quick Search menu is selected the user sees a calendar, which displays recorded dates with highlights. Select a specific date on a calendar. 2. Select a channel from the Channel Selection Screen. Then, a 24-hourly Thumbnail Search screen is displayed. -
Page 51: Event Search
Figure 5.3.2. Time-Line Search Screen When the Timeline menu is selected, the user sees a calendar, which displays recorded dates with highlights. Select a specific date and time. Click and drag the red time indicator bar to the desired hour. You can select specific minutes using a button in the red box shown above. -
Page 52: Go To First Time
Figure 5.3.3.2. Event Search Screen 5-3-4. Go To First Time You can access the oldest recorded data on the EZPZ NVR hard drive by selecting GO TO FIRST TIME on the SEARCH window. Press the PREV button to return to the SEARCH window. -
Page 53: Archive List
5-3-7. Archive List The ARCHIVE Search window is used to find previously stored video or images. Figure 5.3.7. Archive Search Screen When the Archive menu is selected, the user sees a calendar, which has recording data. Select a specific date and the archived data is displayed. Press the Display button to view the still image or the first frame of the selected video, then you can save the selected data. -
Page 54: Play Mode
5-4. Play Mode During playback of a recorded event, the mode changes from SEARCH to PLAY. While in PLAY mode, you may return to the SEARCH screen by pressing the X button on the status bar. Figure 5.4.1. Play Mode Screen The following status bar automatically hides and appears again if a mouse pointer is positioned to the bottom of the screen. -
Page 55: Back-Up
1. When you press the BACKUP button, the NVR will ask whether to archive a Still Image or Video Clip. 2. If you select VIDEO, the EZPZ NVR asks for the media. To use the Huge Backup, an external USB HDD has to be mounted. -
Page 56: Transferring Still Images Or Video From The Archive List
Figure 6.2.1. Video Archiving and Backup Screen 6-3. Transferring Still Images or Video from the ARCHIVE List The stored data onto hard drive is found in the ARCHIVE list in the SEARCH window. You can back up still images or video into the storage device from the ARCHIVE list. 1. -
Page 57: Playback Of Backup Video
Figure 6.3.1. Archive Search Screen 6-4. Playback of Backup Video NSF Format: NSF format video can be played back by the player (the HD player) that the EZPZ NVR copies onto the USB flash drive with the video. Two folders are copied onto the USB flash drive - BACKUP DATA: NSF format video file and the INDEX file for a title file of date and time - HD PLAYER: Exclusive video viewer. -
Page 58: Network Access Using The Ezpz Viewer
7. Network Access Using the EZPZ Viewer 7-1. Overview The EZPZ Viewer is a multiple site monitoring client software with; video, audio, and alarm signals from the EZPZ NVRs over networks. The EZPZ Viewer does not limit the number of NVR units to register. -
Page 59: Installation Of The Program
-3. Installation of the Program 1. Insert the provided CD in the CD drive and double-click “EZPZ Viewer (XXXX).exe” 2. Select a destination folder and click “Next”. 3. Select the program folder and click “Next”. 4. The installation status screen is displayed. -
Page 60: Live Window
7-4. Live Window When installation is complete, double click the “EZPZ Viewer” icon on your desktop to start the program. 7-4-1. Main User Interface For more information on using EZPZ Viewer please refer to our separate EZPZ Viewer CMS manual. -
Page 61: Ip Camera
7-5-1 IP Camera Select EZPZ IP Camera for system and time settings. CHANNEL: Select the Channel to setup an EZPZ IP Camera. • Vendor: Select EZPZ or Genie IP Camera. IP: Enter the IP Address of the Camera. Port: Enter the Camera stream Port Number (default: 554). -
Page 62: Record
7-5-3. Record Select the RECORD tab to set the recording conditions. These settings only apply to the specified channel. Recording Setup • RECORDING MODE: CONTINUOUS, MOTION, SENSOR, SCHEDULE. SENSOR RECODING: Select the Sensor setting for the selected channel. PRE RECORD: Sets whether to perform, or not, Pre-recording. POST EVENT RECORD: Sets the duration of Event recording. -
Page 63: Device
7-5-4. Device Select Device to set device settings of the EZPZ NVR. ALARM OUT: Set the Sensor, Motion, and Video Loss - for triggering the alarm relay. • HDD Error and Video Loss can also be set for triggering a beeping sound. -
Page 64: Storage
7-5-5. STORAGE Select Storage to configure continuous recording settings by overwriting the hard disk and the storage period for the recording data. OVERWRITE: Select On to continue recording, by overwriting when the hard disk becomes full. • DISK INFO: HDD size and free storage. •... -
Page 65: System
7-5-6. SYSTEM Select System for system and time settings. DATE FORMAT: Select the date display format. • CLIENT ACCCESS: Enable/Disable remote access through network client software. • NTP SETUP: Sets whether to synchronise the time using NTP server or not. •... - Page 66 ID: Email User ID. PASSWORD : Email User Password. MAIL TO: Input the appropriate email address to enable sending e-mail reports MAIL FROM (Return Mail Address): Set the source e-mail address to be notified to the destination. SEND MAIL TEST : E-mail settings to send a test mail to the registered account •...
-
Page 67: Security
7-5-7. SECURITY Select the SECURITY tab to set the DISPLAY conditions. USER AUTHORITY: Select which users have access to each function; password check can be • implemented for each function accessed. USER PASSWORD: Select Username to change Password. • CHANGE: Select whether to KEEP or CHANGE the current password. NEW PASSWORD: Input NEW Password if CHANGE was selected. -
Page 68: Network
7-5-8. NETWORK PORT: When connecting multiple NVRs to the network, set a unique port number. • NETWORK AUDIO PORT: Display the network audio port (NETWORK PORT + 1). • WEB PORT: Set a web server port number. • NETWORK TYPE ( Cannot be altered remotely ) •... -
Page 69: Information
7-6-2 IP Camera Setup The menu settings for the IP Cameras can be set over network via the EZPZ Viewer Software. Put the mouse cursor on the channel, which is connected to the site, and right click on the mouse to open the sub-menu. -
Page 70: Live View
7-7-1. Live View Live View using Internet Explorer Open Internet Explorer and enter the camera’s IP address. The system will ask for confirmation to install the Active-X control. Once authorised, Internet Explorer starts to display video images from camera; as shown below 7-7-2. -
Page 71: Security
Frame Rate Determine the maximum number of frames of video images to compress. The frame rate of actually transmitted video can be affected by the network bandwidth limitation Bit Rate Selectable video bit rate. This selection is available if Preference is set to ‘Bit rate ’. 7-7-3. -
Page 72: Network
7-7-5. Network Network Type Select the Network Type (DHCP, Static). DHCP The address setting mode is automatic. Static The address setting mode is manual. Input IP, Gateway, Subnet Mask and DNS IP addresses. 7-7-6. System Information ... -
Page 73: Network Access Using The Web-Browser Viewer
8. Network Access Using the Web-Browser Viewer The EZPZ NVR provides a live remote monitoring feature via a web-browser viewer (Note: Web-Brower is only available for Internet Explorer 10). 1. Check the IP address of the EZPZ NVR from SETUP>SYSTEM>DESCRIPTION>IP ADDRESS. - Page 74 3. Click this bar and this dialogue box is displayed. 4. Click “Install” to download ActiveX control. 5. Web Browser Viewer is displayed as below. 6. Click the CONNECT button on the right upper corner of web-viewer. The “Connect” dialogue box is displayed.
- Page 75 Password: Input the EZPZ NVR network password. (the password is set in SETUP>SYSTEM>NETWORK PASSWORD). 7. The cameras connected to the EZPZ NVR are displayed on the screen. 8. Use the mouse scroll wheel to digitally Zoom In and Out of a single channel display.
-
Page 76: Network Access Using The Smart Phone Viewer
2. Search for “EZPZ Manager” in the App Store. LIVE 1. Open the installed “EZPZ Manager” App and click the button to add a remote device. 2. Enter the site name, IP or DDNS address, Network Port number (default 5445), ID (default admin) - Page 77 4. The App will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4, 9, 10 or 16 channels split display. This App is also used for the Genie EZPZ range. 5. To select the display mode (1, 4, 9, 10 or 16 split display), tap the arrow menus button.
- Page 78 channel to another channel. 7. Digital Zoom In-Out Double tap on the desired channel to view in 1channel mode. Then use the iPhone zoom feature using two fingers to pinch the screen to Zoom In or Out of the video image. You can also move the zoomed image around by touching the desired spot and dragging the zoom image.
-
Page 79: App Viewer For Android Phone
2. Search for “EZPZ Manager” in the Android Market and install the “EZPZ Manager” App. Live 1. Open the installed “EZPZ Manager” App and select Live Preview. Then, click the menu button of the phone to add a remote device. - Page 80 3. The App will display the selected channel(s). Double tap the channel screen to switch 1 channel display to 4 channels split display. Playback 1. Select the registered device and select PLAYBACK and up to 4 channels to search. Then click the START button.
- Page 81 PTZ Control To control the PTZ function of the camera, tap the channel screen, and the channel name will be highlighted in Yellow. Using the PTZ menu icons on the screen, control the PTZ camera.
-
Page 82: Appendix: Network Connection - Lan
APPENDIX: Network Connection – LAN Connect to the system, using a hub (Switching Hub or IP Router) and an Ethernet cable (10BASE- T/100BASE-TX CAT 5e/6 LAN cable). 1. Install the network client software from the supplied CD (Refer to Chapter 7. Network access using the Exclusive network viewer). -
Page 83: Appendix: Network Connection - Internet And Ddns
Port Number: Default Port Number is “5445”. • ID: Input EZPZ NVR ID. Default ID is “admin”. • Password: Input EZPZ NVR network password. Default Password is “1111”. • 5. Select a site by checking the box, and Press the button to connect to the site. - Page 84 2. Go to Setup menu of the Router and open TCP port 5445 and 80 using Port Forwarding. 3. Confirm the Mac address and Serial No. from the label on the rear panel of the EZPZ NVR. 4. Open the web browser and log on http://www.bestddns.com. Please log on http://www.okddns.com in Korea and http://www.ddnscenter.com in USA.