Overview
The MET-ECOM-DNS-B Metreau Entry Communicator with Display (FG2180-07-BK) can be
placed at entry points of homes, condos and hotels to provide audio/video communications
with anyone at a door or gate - all over IP. Any AMX Modero intercom-enabled touch panel
can interface with the Metreau Entry Communicator and allow residents to open doors, gates
and more.
FIG. 1
MET-ECOM-DNS-B Metreau Entry Communicator with Display
Refer to the Metreau Entry Communicators Operation/Reference Guide (available online at
www.amx.com) for additional installation details and instructions on positioning the integrated
video camera, using the Configuration Manager, using the full-duplex intercom, and NetLinx
Programming information.
Note: The MET-ECOM-DNS-B is intended for installation in interior or protected
environments.
Product Specifications
MET-ECOM-DNS-B Specifications
Power:
• PoE powered – no local Power Supply needed
• IEEE 802.3af Compliant
Front Panel Components:
• OLED Display
• Integrated Color Video Camera
• Speaker
• Dual Color LED Status Bar: (Yellow/ Red) can be used
to provide feedback, to attract attention for action, or as
general indicator.
• Pushbutton (Doorbell)
• Microphone
OLED Display:
• 4-bit Gray Scale
• 1.6" Diagonal Display
• 180° Viewing Angle
• 2000:1 Contrast Ratio
• Unit stores up to 50 .bmp images
Integrated Color Video
• QVGA 320 x 240
Camera:
• Supports Motion JPEG (MJPEG) and H.263 codecs.
• Viewing Angle: 42°
Speaker:
• 8 Ohm, 2W
• 80dB SPL (sound pressure level at 1 meter)
• Meets G.711 sound standard
Microphone:
• -40 dB sensitivity, built-in echo cancellation (telephone
quality)
• Full duplex communication
• VoIP Telephony
Rear Panel Components:
• Camera Viewing Angle Adjustment
• Ethernet Port - 10/100 Ethernet with PoE. LEDs show
communication activity, connection status, speeds, and
mode information:
SPD (speed) - Green LED lights On when the
connection speed is 100 Mbps and turns Off when the
speed is 10 Mbps.
L/A (link/activity) - Orange LED lights On when the
Ethernet cables are connected and terminated
correctly, and blinks when receiving Ethernet data
packets.
• ID/Reset pushbutton: Push to set the NetLinx ID
(Device only) assignment for the device. Push and
hold for at least 10 seconds to reset to factory default
settings.
MET-ECOM-DNS-B
OLED display
Video Camera
Speaker
Dual Color LED Status Bar (Yellow / Red)
Pushbutton (Doorbell)
Microphone
™
Metreau
MET-ECOM-DNS-B Specifications (Cont.)
Rear Panel Components
• Status LED: Green LED provides an indication of both
(Cont.):
the system status and communication status with the
target Master. 1 blink every 5 seconds indicates there
is currently active communication between the
Metreau unit and a target Master.
• 2 Multi-Purpose I/Os (5V): 2-channel binary I/O ports
for contact closure with each input being capable of
voltage sensing. Input format is software selectable
with interactive power sensing for IR ports.
• 2 Low Voltage Relays (1A contact): 2-channel single-
pole single throw relay ports with each relay being
independently controlled and supporting up to 2
independent external relay devices.
Dimensions (HWD):
• 6.500" x 4.185" x 1.493"
(16.510 cm x 10.629 cm x 3.792 cm)
Weight:
1.30 lbs (0.59 kg)
Operating Environment:
32° - 104° F (0° - 40° C)
Colors Available:
Black
Included Accessories:
• Installation Kit - includes 2 Phoenix connectors (female,
3.5mm) and one Ferrite clip.
Other AMX Equipment:
• Rough-In Box (required for installation - FG039-13)
• PS-POE-AF Power-over-Ethernet (PoE) power supply
(FG423-80)
• NXA-ENET24 Managed Ethernet Switch (FG2178-60)
• NXA-ENET24PoE Managed Ethernet Switch, Power
Over Ethernet (FG2178-61)
Certifications:
• FCC Class B
• CE
• IEC60950
• RoHS
Rear Panel Components
FIG. 2 shows the location of the rear panel components for the MET-ECOM-DNS-B.
Camera Viewing
Angle Adjustment
ID/Reset pushbutton
STATUS (red LED)
Ethernet Connection
2 Multi-Purpose I/Os (5V)
2 Low Voltage Relays (1A Contact)
FIG. 2
MET-ECOM-DNS-B (rear panel)
Wiring and Connections
Note: To avoid any damage to the electronic component, installation must be performed in an
ESD safe environment.
Note: Do not connect power to the MET-ECOM-DNS-B until the wiring is complete.
After you have completed the installation, consult the Using the Configuration Manager
section of the Metreau Entry Communicators Operation/Reference Guide.
Installation Guide
Entry Communicator with Display
Mounting
Magnets
(2 on each side)