HISTORY INFORMATION FOR THE FOLLOWING MANUAL: WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26S3000 RM-YD018 US/CANADA KDL-32S3000 RM-YD018 US/CANADA KDL-40S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 US/CANADA ORIGINAL MANUAL ISSUE DATE: 4/2007 REVISION DATE SUBJECT 4/2007 No revisions or updates are applicable at this time.
Page 2
Self Diagnosis Supported model WAX3 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION KDL-26S3000 RM-YD018 US/CANADA KDL-32S3000 RM-YD018 US/CANADA KDL-40S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 US/CANADA KDL-46S3000 RM-YD018 LCD DIGITAL COLOR TELEVISION 9-883-745-01...
Trademark Information “BRAVIA” and , S-Force, BRAVIA Theatre Sync, and DMe trademarks or registered marks of Sony Corporation. Blu-ray Disc is a trademark. “XMB”, “XrossMediaBar” and “PS3” are trademarks of Sony Corporation and/or Sony Computer Entertainment Inc. This TV incorporates High-Definition Multimedia Interface (HDMI™) technology.
KDL-26S3000/32S3000/40S3000/46S3000 SAFETY-RELATED COMPONENT WARNING There are critical components used in LCD color TVs that are important for safety. These components are identifi ed with shading and mark on the schematic diagrams and the electrical parts list. It is essential that these critical parts be replaced only with the part number specifi...
Page 7
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com KDL-26S3000/32S3000/40S3000/46S3000...
KDL-26S3000/32S3000/40S3000/46S3000 SAFETY CHECK-OUT The AC leakage from any exposed metal part to earth ground and After correcting the original service problem, perform the following from all exposed metal parts to any exposed metal part having a safety checks before releasing the set to the customer: return to chassis, must not exceed 0.5 mA (500 microamperes).
KDL-26S3000/32S3000/40S3000/46S3000 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY LED indicator will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 10
KDL-26S3000/32S3000/40S3000/46S3000 Viewing the Self Check Diagnostic List 1. TV must be in standby mode. (Power off). 2. Press the following buttons on the Remote Commander within a second of each other: Channel 5 Volume - TV POWER . DISPLAY The Self Check list displays.
KDL-26S3000/32S3000/40S3000/46S3000 1-5. U1 BOARD, DTT SHIELD, AND JACK HOLDER REMOVAL Disconnect one connector Remove one screw, +BVTP 3X12 TYPE2 IT-3 Release hooks and remove U1 Board. Remove Jack holder from Bezel. Release hooks to remove DTT Shield from BU1 bottom shield.
KDL-26S3000/32S3000/40S3000/46S3000 1-10. D2 BOARD REMOVAL (KDL-46S3000 ONLY) Disconnect 3 connectors Remove 4 screws, +PSW 3SG D2 Board D2 Bracket 1-10-1. REPLACING THE INVERTER CONNECTOR ASSEMBLY (KDL-46S3000 ONLY) Use the following procedure to confirm that the Inverter connector is securely attached to the board.
KDL-26S3000/32S3000/40S3000/46S3000 1-14. LCD PANEL, LED AND GUIDE LIGHT REMOVAL (KDL-40S3000/46S3000 ONLY) Remove 2 screws from Bezel and Top Brackets, +BVTP2 4X16 Remove 4 screws from Top Brackets, +PSW M5X8 Remove 4 screws from Bottom Brackets, + PSW M5X12 Remove 4 screws from Stand Holders, +PSW M5X16...
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY OVERALL VIEW × KDL-26S3000/32S3000/40S3000/46S3000...
Page 17
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H3 BOARD HARNESS OPERATION PROCESS 1. Apply Sheet Core C to edge of Panel to cover sharp edge of panel. Use ribs on bezel (w/o screw boss) as a guide to center tape. Use H3/H4 Harness "Split" as reference for top of Cushion D Position 2.
Page 18
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD OPERATION PROCESS 1. H4-Bd should be installed BEFORE the speaker/baffles are installed 2. Be careful to align Plastic clip at left side of bezel with notch in PWB. 3. PRESS FIRMLY on PWB next to clip to seat H4-Bd.
Page 19
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD AND RIGHT SPEAKER OPERATION PROCESS 1. Wire Dress Right Speaker wires and H4 cables in side clamp (white) and G3-Bd bracket clips (black). NOTE: ALL Wires are dressed in far left G-Bracket clip! NOTE: Keep H4 cables AWAY From INVERTER BOARD AREA! NOTE: H4-Bd/Rt.
Page 20
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H4 BOARD AND RIGHT SPEAKER (CONTINUED) OPERATION PROCESS NOTE BOTH H4-Bd and Rt. Speaker cables 1. Dress H4/Rt. Speaker cables in white are dressed UNDER AC Inlet side clips. 2. Dress AC Inlet Cables in Plastic clip on the G-Bracket as shown.
Page 21
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY CORE BLOCK HARNESS OPERATION PROCESS 1. Route/Dress Harnesses connected to Core Block as Shown 2. NOTE Order & Direction of Cables in plastic Clip on Shield Case. Route 1st Route 3rd Route LAST Keep Cables BELOW level...
Page 22
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY CORE BLOCK HARNESS (CONTINUED) OPERATION PROCESS 1. Route/Dress Core-Block cables as shown 2. Put Attention on the position of Sheet Core C and the routing of the cables between G3-Bd and Core Block. Apply Sheet Core C to dress cables.
Page 23
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY INVERTER BOARD AND D1 BOARD OPERATION PROCESS INVERTER INVERTER CAUTION MAKE SURE BLACK INSULATION O.K. N.G. TUBING DOES NOT TOUCH CONN BEFORE INSTALLING 2P MD CONN. AFTER INSTALLING CONNECTOR, TUBE INSULATION CAN TOUCH CONNECTOR! INSTALL INVERTER SIDE 1ST INSTALL D1-Bd SIDE 2ND O.K.
Page 24
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY INVERTER BOARD AND D1 BOARD (CONTINUED) OPERATION PROCESS INVERTE CAUTION: MAKE SURE WHITE/PINK WIRES DO NOT CROSS CHECK INVERTER SIDE WIRES CHECK D1-Bd SIDE WIRES CAUTION: Make Sure Inverter Connector DOES NOT CROSS WHITE/PINK WIRES! CHECK BOTH SIDES OF HARNESS!
Page 25
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY G3 BOARD AND D1 BOARD OPERATION PROCESS 1. Install/Wire Dress Harnesses as shown. NOTE: Ferrite Core and Sheet Core A 2. CAUTION: Make sure INVERTER CONN. Applied by SBC Plants. is Fully LOCKED!! CAUTION: Make Sure Inverter Connector is Fully LOCKED!
Page 26
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY D1 BOARD AND INVERTER BOARD CAUTION OPERATION PROCESS 1. MAKE SURE COLOR of UL tape is the correct color (YELLOW) for harness. Confirm wires are dressed properly in clips. 2. Confirm 2P BD Connectors are FULLY LOCKED by pressing on BOTH locking tabs (RED ARROWS).
Page 27
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY SPEAKER CABLES OPERATION PROCESS 1. Wire Dress Speaker Cables as shown. Lft. Speaker cable is dressed in side clamp (white plastic). 2. BOTH R/L cables are dressed in FGC-3 conductive clip. TORQUE SPECIFICATION TORQUE: 6kg.cm (+-1.0kg.cm) Lft. SPEAKER Cables...
Page 28
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY LEFT SPEAKER HARNESS OPERATION PROCESS 1. Dress LEFT speaker harness as shown Side Clamp Installed by Vendor. PUSH SIDE CLAMP THIS DIRECTION TO LOCK!! Side Clamp Installed by SBC PLANT! KDL-26S3000/32S3000/40S3000/46S3000...
Page 29
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY U1 BOARD OPERATION PROCESS 1. Apply Sheet Core A to Panel in location where U2 bracket is to be installed (Use plastic ribs on bezel as guide) 2. Make sure DTT Shield has Sheet Core C Align with center of circles on Install Sheet Core C on "dimple"...
Page 30
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY U1 BOARD (CONTINUED) OPERATION PROCESS 1. Wire route ESD GND wire as shown (NOTE: Actual Part will have BLUE insulation) 2. Use 3x12mm screw to fix ring terminal in U1 Bracket 3. Apply Sheet Core C to hold cable on panel.
Page 31
KDL-26S3000/32S3000/40S3000/46S3000 KDL-40S3000 ONLY H1 BOARD OPERATION PROCESS 1. Dress/Route H1-Bd harness as shown on photo. 2. NOTE: Put attention on SLACK of cable. Between Connector on H1 and tape there is slack in wire. Between tapes there is a little slack.
KDL-26S3000/32S3000/40S3000/46S3000 SECTION 2: SERVICE ADJUSTMENTS 2-1. USING THE REMOTE COMMANDER 2-3. VIEWING THE SERVICE MENUS FOR ELECTRICAL ADJUSTMENTS Use the Remote Commander to view the BE and Digital service menus options. To adjust various set features, use the Remote Commander to put the set into service mode to display the service menus and categories.
KDL-26S3000/32S3000/40S3000/46S3000 2-4. USING THE REMOTE COMMANDER TO 1. Access Service Adjustment Mode and select the Service Menu that contains the Category with the Adjustment Item you want to change. VIEW SERVICE DATA 2. To change the Category, press 2 or 5 on the Remote Commander.
KDL-26S3000/32S3000/40S3000/46S3000 2-5. VERIFYING SERVICE DATA CHANGES 1. After completing all adjustments turn the set off with the Remote Commander and then proceed to the next step. 2. Press the following buttons on the Remote Commander within a second of each other:...
KDL-26S3000/32S3000/40S3000/46S3000 3-2. PRINTED WIRING BOARDS AND Terminal name of semiconductors in silk screen SCHEMATIC DIAGRAMS INFORMATION printed circuit ( All capacitors are in μF unless otherwise noted. pF : μμF 50WV or Circuit Device Printed symbol Terminal name Collector less are not indicated except for electrolytics and tantalums.
KDL-26S3000/32S3000/40S3000/46S3000 3-3. BLOCK DIAGRAM SIGNAL FLOW DIAGRAM Audio Audio Audio Audio HDMI HDMI HDMI HDMI for PC for PC for DVI for DVI UART 8bit Multiplex BUS 4M x 32bit BE Micro MB91305 Flash Panel NAND NAND Flash Flash DDR2...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (2 OF 12) A_HP_OUT_R A_HP_OUT_L AUDIO_9V A_SP_OUT_R MUTE_AU13V A_SP_OUT_L PQ200WNA1ZPH — A_LINE_OUT_R I C 2005 AU_13V A_LINE_OUT_L AUDIO_13V TAS ANALOG 3.3V R 2202 L 2016 F 2000 22uH 1/16W C 2123 CHIP D3.3V D2014 C 2121 C 2159 0.
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (3 OF 12) << ST B Y 3.3V >> ST B Y 3.3V M24256-BWMN6TP(A) RESET R 3167 I C 3005 X 3009 1/16W EEPROM 32. 768kH z R 3144 — 2 . 2 k CHIP...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (4 OF 12) JL 4508 TMDS_RX0- Y_G1 R X 0- TO HDMI JL 4509 TMDS_RX0+ PB_B1 RX0+ JL 4510 •¡ SV P-PX P DDR & CPU I/F, POWE R & GND PB_R1 TMDS_RX1- — R X 1-...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (7 OF 12) ST B Y 3.3V R 4048 FB 4011 1/10W L FB K 1608HS601 RN-CP 0.5% FB 4005 D3.3V R 4047 — STBY 3.3V 2 . 2 k DIMMER DIMMER 1/16W FB 4009...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (8 OF 12) D2.5V — C 7077 1608 R 7047 C 7047 2 . 2 k 220p 1/16W RN-CP 0.5% R 7059 REG12V — 1/16W CHIP R 7035 R 7041 R 7048 R 7055 3 . 3 k...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (9 OF 12) X IL L EON242 GROUND BAL L S ASIC CORE POWER D2.5V _A T I D1.0V D3.3V _A T I COR E _1.0V (NE E D <50mV NOI SE ) — FB 7200...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (10 OF 12) — MEMORY CONFIGURATION VDDR_MEM DDR _1.8V DRAM_IF DDR2 SDRAM WAX 3 L 7431 MEM_DQA0 I C 7400 R 24 * C 7430 C 7431 DQA_0 HY B 18T C512160B F-2.5 0 . 1...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (11 OF 12) DIGITAL GR APHICS OUT (DDR ) — GRAPHICS DDR->SDR LATCH EGPHSI EGPHSI D3.3V FB 7601 DV I_IF EGPV SI EGPV SI C 7611 — DVIDATA0 EGPPCI EGPPCI T C74V CX 162374(E L ,F...
KDL-26S3000/32S3000/40S3000/46S3000 BU1 BOARD SCHEMATIC DIAGRAM (12 OF 12) V IDEO_IF FRONT_END_IF — R 7712 R 7710 1/16W V I _I N0 CHIP R 7706 1/16W * C 7818 L 7801 C 7828 V I _I N1 C 7821 C 7823...
KDL-26S3000/32S3000/40S3000/46S3000 G1H BOARD SCHEMATIC (POWER SUPPLY) (KDL-32S3000 ONLY) This board is manufactured by a 3rd party. Component level repair information is not available. [POWER SUPPLY] PWB IS NOT AVAILABLE KDL-26S3000/32S3000/40S3000/46S3000...
Page 56
KDL-26S3000/32S3000/40S3000/46S3000 G3 BOARD SCHEMATIC (POWER SUPPLY) (KDL-40S3000/46S3000 ONLY) Mount Mecha A6000 214976631 D6000 L6501 t @ X g 300uH C6515 C6516 R6106 L6150 Mount Mecha A6150 234989201 D6151 CN6003 470p 470p R6524 R6014 C6019 D6151 6 . 8 1/10W D4SBS6 0 .
KDL-26S3000/32S3000/40S3000/46S3000 H1 BOARD SCHEMATIC DIAGRAM POWER — H1 BOARD S101 USER CONTROL — HOME INPUT SEL VOL+ VOL- MENU TO BU1 WEGAGATE POWER INT CN3008 KEY1 — R107 R102 CN101 S104 S107 S106 S105 S103 S102 — R104 R101 R105 R103 1 .
Page 59
KDL-26S3000/32S3000/40S3000/46S3000 [USER CONTROL] COMPONENT SIDE VOL+ R102 S104 VOL- VIA G[CV OK S105 R103 INPUT SEL S103 R108 S106 R101 R107 S107 R104 S101 POWER S102 HOME 1-872-981-11 A-1220- MENU C103 (172841011) WEGAGATE [USER CONTROL] CONDUCTOR SIDE CN102 CN101 JL101...
REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] (Please review the Sony Electronics Service Information website for any additional service information.) 3-100-157-01 COVER, REAR (26) 3-215-345-01 LABEL, INFORMATION (KDL-26S3000 ONLY) (KDL-32S3000 ONLY) 7-685-648-79 SCREW +BVTP 3X12 TYPE2 TT(B)
See Appendix A: Encryption Key Components in the back of this manual. 4-2. BEZEL ASSEMBLY AND LCD PANEL (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 REF. NO.
See Appendix A: Encryption Key Components in the back of this manual. 4-3. CHASSIS (KDL-26S3000/32S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.)
See Appendix A: Encryption Key Components in the back of this manual. 4-4. CHASSIS (KDL-40S3000/46S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-674-965-41...
See Appendix A: Encryption Key Components in the back of this manual. 4-5. CONNECTORS (KDL-26S3000/32S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF.
See Appendix A: Encryption Key Components in the back of this manual. 4-6. CONNECTORS (KDL-40S3000/46S3000 ONLY) (Please review the Sony Electronics Service Information website for any additional service information.) REF. NO. PART NO. DESCRIPTION [ASSEMBLY INCLUDES] REF.
See Appendix A: Encryption Key Components in the back of this manual. 4-7. SPEAKERS (Please review the Sony Electronics Service Information website for any additional service information.) 2-580-640-01 SCREW, +BVTP2 4X16 2-580-600-01...
Page 81
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 82
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 83
S29AL016D70TFI010-WAX3A4U J1700 1-821-026-11 OPTICAL OUT TERMINAL (KDL-26S3000 ONLY) J1701 1-820-765-11 PHONO JACK IC3002 6-807-481-03 S29AL016D70TFI010-WAX3A2 J1710 1-820-638-11 JACK (SMALL TYPE) (ALL EXCEPT KDL-26S3000 ONLY) IC3004 6-703-175-01 PST3629UL J5000 1-821-013-11 D SUB CONNECTOR IC3005 6-710-121-01 M24256-BWMN6TP(A) J5502 1-818-737-11 HDMI CONNECTOR IC3006...
Page 84
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 95
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 96
KDL-26S3000/32S3000/40S3000/46S3000 D1 D2 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R6736 1-218-885-11 METAL CHIP 0.50% 1/10W R6805 1-216-793-11 METAL CHIP 1/10W R6737 1-216-821-11 METAL CHIP 1/10W R6806 1-216-864-11 SHORT CHIP R6739 1-216-864-11 SHORT CHIP R6750...
Page 97
SHORT CHIP JR6902 1-216-296-11 SHORT CHIP 1-474-056-11 G1D BOARD, COMPLETE (POWER SUPPLY) JR6903 1-216-296-11 SHORT CHIP (KDL-26S3000 ONLY) This board is manufactured by a 3rd party. COIL Component level repair information is not available. L6900 1-406-977-21 INDUCTOR 100μH TRANSISTOR Q6902...
Page 98
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 99
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 100
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
Page 101
KDL-26S3000/32S3000/40S3000/46S3000 NOTE: Les composants identifi es per un trame et une NOTE: The components identifi ed by shading marque sont critiques pour la securite. Ne les remplacer mark are critical for safety. Replace only que par une piece portant le numero specifi e.
MUST BE RETURNED to Sony. b) and if the core charge is NOT covered under the product warranty, the defective un-repaired or modifi...
Page 106
In an effort to reduce the size of this pdf file the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.