Related Manuals for Polk Audio TC610i
Summary of Contents for Polk Audio TC610i
- Page 1 TC610 i TC615 i O w n e r ’s M a n u a l High Performance In-Wall Speakers t h e s p e a k e r s p e c i a l i s t s ®...
-
Page 2: Placement Options
PLACEMENT OPTIONS ADJUSTING THE TWEETER Polk Audio TCi Series In-Wall Loudspeakers Aiming the tweeter toward your listening give you nearly endless placement options. position improves imaging and detail. When But remember that placement choice for your using TCi Series In-Wall Loudspeakers as... - Page 3 No haga girar el tweeter como si fuera el pomo de una puerta. más difuso. TC610i: Pour orienter le tweeter,tenez-le du bout des doigts et faites-le Exemples d'installations au mur et au plafond. Pour usage arrière-ambio- pivoter dans la direction désirée. Ne le tournez jamais comme une phonique, dirigez les tweeters vers la surface réfléchissante la plus proche (mur...
-
Page 4: Preparing To Paint
PAINTING YOUR TCI SERIES IN-WALL PREPARING TO PAINT: LOUDSPEAKERS 1. Separate the parts of the speaker. If the You will need: speaker is not yet installed, the grille can be removed simply by pushing the clamp • Paint of your choice (to make the job easi- screws forward to push the grille off the er, we recommend spray painting the grille) speaker from the inside. -
Page 5: Painting The Frame
PAINTING THE FRAME: 1. Apply paint to exposed (unmasked parts). 4. After removing the grille by carefully hook- Use two or more thin coats. Spray painting ing it with a bent paper clip and pulling it is recommended [figure 7]. gently away from the frame, spray on two thin coats of finish color. -
Page 6: Installation
Wiring is best performed by an expe- rienced professional. If you are in doubt that you possess the necessary skills or tools, consult your Polk Audio dealer, or a profes- sional installer. POP-OUT AREA TEMPLATE... - Page 7 FOLLOW THESE EASY STEPS: • Carefully cut the hole with the appropriate • Make sure the material into which you plan cutting tool for your wall or ceiling material. to mount the speakers (plaster, drywall, paneling, stone, etc.) can support the Start the hole by drilling a hole on the inside weight of the speakers (see specification of the tracing (with the drill bit touching the...
- Page 8 • To install the speaker, first carefully remove • Carefully reinstall the grille by fitting it into the grille using a straightened paperclip or its recess so that it is just resting on the other pointed metal tool. Insert the point frame.
-
Page 9: Safety First
SAFETY FIRST When installing your TCi Series In-Wall If you plan to install your TCi Series speakers Loudspeakers, be aware of the weight of your where water will directly contact them, it is advisable to use a silicone sealant or caulk particular model (see specification page for between the frame of the speaker and the the weight of your model) and the sturdiness... -
Page 10: Specifications
Cutout Dimensions 7c" x 10w" (18.6cm x 27.3cm) 18.57cm x 27.31cm Depth with drywall 2" 2v" (6.19cm) Shipping Weight Each 4 LBS- 3.63 Kg TC610i Frequency Response 40Hz-20kHz Recommended Power 20-100Wrms Impedance Compatible with 8 Ohm amplifiers Efficiency (dB 1W/1m) 89db... - Page 11 Distributors in such countries. disaster, misuse, abuse, negligence, “Polk Audio,” “Polk,” “The Speaker Specialists,” “Power Port” and “Dynamic Balance” are trademarks of Britannia Investment Corporation used under license by Polk Audio Incorporated. Dolby, Pro Logic, Dolby Digital and AC-3 are trademarks of Dolby Laboratories Licensing Corp.
- Page 12 t h e s p e a k e r s p e c i a l i s t s ® 5601 METRO DRIVE, BALTIMORE, MARYLAND 21215, USA, 800-377-7655, FAX: 410-764-5266 www.polkaudio.com...