Table of Contents
Related Manuals for HERO HRO-ST3131
Summary of Contents for HERO HRO-ST3131
- Page 1 WARNING DO NOT ATTEMPT TO OPERATE THIS MACHINE UNTIL YOU HAVE READ AND UNDERSTOOD ALL SAFETY PRECAUTIONS AND OPERATING INSTRUCTIONS. EQUIPMENT AND CHEMICALS WHEN USED IMPROPERLY CAN BE DANGEROUS. HRO-ST3131 Page 1 Mar 8, 2004...
- Page 2 To qualify for the warranty, the warranty card (attached to this page) supplied with this H.E.R.O. airless pump, must be completed with equipment serial number and signed by the purchaser, and postmarked within ten (10) days of purchase. HRO-ST3131 Page 2 Mar 8, 2004...
-
Page 3: Unit Layout
Pump Outlet Spray Hose Hook Up Drive Belt Hydraulic Pump & Pressure Control Hydraulic Pump Shut Off Valve Hydraulic Fluid Fill & Vent Hydraulic Fluid Level Gauge Paint Piston Pump Suction Tube & Suction Filter HRO-ST3131 Page 3 Mar 8, 2004... -
Page 4: General Safety Warning
SPRAY PUMPS. Gas / Hydraulic powered airless spray equipment is an industrial paint sprayer which uses a gas engine to drive a hydraulic pump which in turns produces hydraulic pres- sure. This pump delivers pressure fluid to a hydraulic mo- tor which drives a high pressure airless piston pump. - Page 5 Workman and assistant must always wear protective eyewear, gloves, clothing, and respirator as recommended by the material manufacturer. HRO-ST3131 PRESSURE RELIEF PROCEDURE Always follow “PRESSURE RELIEF PROCEDURE’’ before servicing, cleaning or removal of the spray tip to prevent serious bodily injury, fluid injection, or splashing in the eyes.
- Page 6 Suction tube filter - Removes harmful and course materials from entering pump. HRO-ST3131 Filter manifold - Removes and filters out the impu- rities from the paint before reaching the spray tip. Prime valve - Releases fluid pressure from the pump, hoses and guns.
-
Page 7: Operation
Keep the pump, hose and gun clean inside and outside. HRO-ST3131 OPERATION Follow the “Pressure Relief Procedure” before operating. FLUSHING TO CLEAN SYSTEM Flush the pump, hose and gun with the solvent as Recommended by your material supplier. -
Page 8: Setting Up To Spray
If atomization is not possible on thick paints, thin with the compatible solvent. HRO-ST3131 Use the lowest pressure setting possible. If the pump accelerates quickly or is running too fast, stop the pump immediately and check the mate- rial supply. -
Page 9: Troubleshooting
Pressure 2. Worn Upper Packings, Intake or Outgo balls and / or seats. 3. Cylinder sleeve leakage. 4. Worn spray tip. HRO-ST3131 TROUBLE SHOOTING Page 9 REMEDY 1. Turn ball valve to the on position. 2. Fill with correct fluid. -
Page 10: Maintenance
If atomization is not possible on thick paints, thin with the compatible solvent. HRO-ST3131 Use the lowest pressure setting possible. If the pump accelerates quickly or is running too fast, stop the pump immediately and check the mate- rial supply tank. -
Page 11: Flushing Procedure
RELIEVE PRESSURE BY TRIGGERING GUN. NOTE: TO PREVENT CORROSION AND TO REDUCE THE RISK OF FLUID FREEZING IN THE PUMP. NEVER STORE THE UNIT WITH PAINT OR WATER IN THE PUMP SYSTEM, EVEN OVERNIGHT! HRO-ST3131 FLUSHING PROCEDURE Page 11 Mar 8, 2004... - Page 12 H.E.R.O. INDUSTRIES 2719 LAKE CITY WAY Phone: Fax: __________________________ __________________________ __________________________ __________________________ Model: __________________ Serial #: _________________ Date of Purchase: HRO-ST3131 Manufactured by: BURNABY, B.C. CANADA 604-420-6543 800-494-4376 604-420-8725 Purchased From Page 12 Mar 8, 2004...
Need help?
Do you have a question about the HRO-ST3131 and is the answer not in the manual?
Questions and answers